iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 1254-8:2021/oprA1:2024

(Amendment)

Copper and copper alloys - Plumbing fittings - Part 8: Press fittings for use with plastics and multilayer pipes

Copper and copper alloys - Plumbing fittings - Part 8: Press fittings for use with plastics and multilayer pipes

This document specifies product characteristics, assessment methods, compliance criteria of test results and a designation system for fittings with radial and axial press ends for use with plastics and multilayer pipes. The fitting ends have a nominal diameter from 10 mm to 160 mm. The fittings are designed for a service lifetime up to fifty.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Adaptor fittings for use with plastics and multilayer pipes may combine press ends with fitting ends defined in the other parts of EN 1254.
Press fittings for use with plastics and multilayer pipes may also have flanged end connections according to EN 1092-3.
Press fittings for use with plastics and multilayer pipes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this document are intended to be used in:
a) liquid applications:
- hot, cold or combined hot and cold water, including systems according to EN 806;
- closed heating systems according to EN 12828;
- cooling systems;
- drainage systems;
- fire protection systems including sprinkler systems according to EN 12845;
- supply systems for points of consumption with liquid fuels according to EN 12514.
b) gas applications:
- natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
- compressed air systems.

Kupfer und Kupferlegierungen - Fittings - Teil 8: Pressfittings für den Einsatz mit Kunststoff- und Mehrschichtverbundrohren

Cuivre et alliages de cuivre - Raccords - Partie 8 : Raccords à sertir pour tubes en matières plastiques et multicouches

Baker in bakrove zlitine - Fitingi - 8. del: Fitingi s stiskalnimi priključki za spajanje s plastičnimi in večplastnimi cevmi - Dopolnino A1

General Information

Status
Not Published
Public Enquiry End Date
29-Sep-2024
ICS
23.040.40 - Metal fittings
77.150.30 - Copper products
Technical Committee
INEK - Nonferrous metals
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
29-Jul-2024
Due Date
16-Dec-2024
Ref Project
EN 1254-8:2021/prA1 - Copper and copper alloys - Plumbing fittings - Part 8: Press fittings for use with plastics and multilayer pipes

Relations

Amends
SIST EN 1254-8:2021 - Copper and copper alloys - Plumbing fittings - Part 8: Press fittings for use with plastics and multilayer pipes
Effective Date
17-Apr-2024

Buy Standard

EN 1254-8:2021/oprA1:2024EN 1254-8:2021/oprA1:2024
PreviousNext
Draft
EN 1254-8:2021/oprA1:2024
English language
5 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)


SLOVENSKI STANDARD
01-september-2024
Baker in bakrove zlitine - Fitingi - 8. del: Fitingi s stiskalnimi priključki za spajanje
s plastičnimi in večplastnimi cevmi - Dopolnino A1
Copper and copper alloys - Plumbing fittings - Part 8: Press fittings for use with plastics
and multilayer pipes
Kupfer und Kupferlegierungen - Fittings - Teil 8: Pressfittings für den Einsatz mit
Kunststoff- und Mehrschichtverbundrohren
Cuivre et alliages de cuivre - Raccords - Partie 8 : Raccords à sertir pour tubes en
matières plastiques et multicouches
Ta slovenski standard je istoveten z: EN 1254-8:2021/prA1
ICS:
23.040.40 Kovinski fitingi Metal fittings
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

DRAFT
EUROPEAN STANDARD
EN 1254-8:2021
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
July 2024
ICS 23.040.40
English Version
Copper and copper alloys - Plumbing fittings - Part 8: Press
fittings for use with plastics and multilayer pipes
Cuivre et alliages de cuivre - Raccords - Partie 8 : Kupfer und Kupferlegierungen - Fittings - Teil 8:
Raccords à sertir pour tubes en matières plastiques et Pressfittings für den Einsatz mit Kunststoff- und
multicouches Mehrschichtverbundrohren
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 133.

This draft amendment A1, if approved, will modify the European Standard EN 1254-8:2021. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1254-8:2021/prA1:2024 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
1 Modification to Clause 1 “Scope” . 4
2 Mod
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 1254-6:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 6: Push-fit fittings for use with metallic tubes, plastics and multilayer pipes
EN 1254-6:2021

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for push-fit fittings for the purpose of joining tubes of copper, plated copper, multilayer pipes and plastics pipes. The fitting ends have a size range from 6 mm to 54 mm. The fittings are designed for a service lifetime up to fifty years.
This document is applicable to push-fit fittings for joining one or more of the following tubes or pipes:
-   copper tubes to EN 1057; copper composite according to UNI 11342, plastic and multilayer pipes covered by EN 15015.
The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Adaptor fittings may combine push-fit ends with fitting ends defined in the other parts of EN 1254.
Push-fit fittings for metallic tubes may also have flanged end connections according to EN 1092-3.
Push-fit fittings may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845.

  • Standard
    28 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-20:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 20: Definitions, thread dimensions, test methods, reference data and supporting information
EN 1254-20:2021

This document contains definitions, thread dimension, reference data (minimum bore), supporting information (assembling instructions) and describes the test methods referenced by other parts of the EN 1254 series.
Thread dimensions comprise: wall thickness at threaded portions of fittings, dimensions of tail pipe ends for swivel fittings, dimensions of gas union connectors, thread dimensions and thread profile.
Test methods comprise: leak tightness under internal hydrostatic pressure, leak tightness under internal pneumatic pressure, resistance of joints to static flexural strength, resistance to pull out of joints, leak tightness of joints under vacuum, the resistance of joints to temperature cycling, resistance of joints with metallic tube to vibration, integrity of fabricated fitting bodies or having an 'as cast' microstructure, resistance to stress corrosion, detection of a carbon film on the surface of copper fittings, determination of mean depth of dezincification, resistance of joints to pressure cycling, disconnection and re-use, determining if the diameter and/or the length of engagement of a capillary end is/are within the specified tolerance, determining the minimum length of engagement of an integral solder or brazing ring socket having a formed groove.

  • Standard
    65 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-4:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 4: Threaded fittings
EN 1254-4:2021

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for threaded fittings. These threaded ends exist with metallic and with non-metallic sealing elements for the purposes of joining with tubes, pipes, fittings or valves, the threaded ends have a size range from 3,175 mm (1/8") to 101,6 mm (4"). The threaded fittings are designed for a service lifetime up to fifty years.
The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Threaded fittings may also have flanged end connections according to EN 1092-3.
Threaded fittings may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this document are intended to be used in:
a)   liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845.
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-5:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 5: Capillary fittings with short ends for brazing to copper tubes
EN 1254-5:2021

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for capillary fittings with short ends for brazing to copper tubes e.g. EN 1057, EN 13348, EN 13349, EN 12735-1, EN 12735-2, etc. These fitting ends exist in two forms: end feed fittings and integral brazing ring fittings. For the purposes of joining copper tubes, the fitting ends have a size range from 14,7 mm to 159 mm. The fittings are designed for a service lifetime up to fifty years.
The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
The capillary fittings with short ends for brazing to copper tubes are used with brazing alloys in accordance with alloys specified in EN ISO 17672.
Not all copper alloys that can be used to manufacture fittings can be brazed and those that can be brazed may require different brazing techniques (guidance is provided in in prEN1254-20:2019, Annex A).
Fittings with short ends for capillary brazing may also have threaded end connections. These threaded ends exist with metallic and with non-metallic sealing elements. For the purposes of joining with tubes, pipes, fittings or valves, the threaded ends have a size range from 1/8" to 4".
Adaptor fittings for use with copper tubes may combine short ends for capillary brazing with fitting ends defined in the other parts of EN 1254.
Capillary fittings with short ends for brazing may also have flanged end connections according to EN 1092-3.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845;
-   refrigeration systems.
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems;
-   medical gas systems according to EN ISO 7396;
-   refrigeration systems.

  • Standard
    26 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-3:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 3: Compression fittings for use with plastics and multilayer pipes
EN 1254-3:2021

This document specifies product characteristics, assessment methods, compliance criteria of test results and a designation system for fittings with compression ends for use with plastic and multilayer pipes which are defined in the applicable pipe standard. For the purposes of joining plastics pipes, the fitting ends have a size range from 10 mm to 160 mm. The fittings are designed for a service lifetime up to fifty years.
The compression fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
This European Standard applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Adaptor fittings for use with plastic and multilayer pipes may combine compression ends with fitting ends defined in the other parts of EN 1254.
Compression fittings for use with plastic and multilayer pipes may also have flanged end connections according to EN 1092-3.
Compression fittings for use with plastic and multilayer pipes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   Hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845.
b)   gas applications (not valid for multilayer pipes):
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    36 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-7:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 7: Press fittings for use with metallic tubes
EN 1254-7:2021

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for press fittings including their elastomeric seals, for connecting with metallic tubes. The fitting ends have a size range from 6 mm to 108 mm. The press fittings are designed for a service lifetime up to fifty years.
This document is applicable to press fittings for joining one or more of the following tubes:
-   copper tubes to EN 1057 and
-   stainless steel tubes to EN 10312
with wall thicknesses and tempers as specified by the manufacturer.
The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
Press fittings are used with tubes with wall thicknesses greater than or equal to the wall thickness given in Annex B, to ensure that tubes can withstand the radial pressing forces involved.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Adaptor fittings for use with copper tubes may combine press ends with fitting ends defined in the other parts of EN 1254.
Press fittings for use with metallic tubes may also have flanged end connections according to EN 1092-3.
Press fittings for use with metallic tubes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   hot or cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845.
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-1:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 1: Capillary fittings for soldering or brazing to copper tubes
EN 1254-1:2021

This document specifies product characteristics, assessment methods, compliance criteria of the test results and a designation system for fittings with ends for capillary soldering or capillary brazing for connecting with copper tubes e.g. EN 1057, EN 13348, EN 13349, EN 12735-1, EN 12735-2 etc. For the purposes of joining copper tubes, the fitting ends have a size range from 6 mm to 108 mm. These fitting ends exist in three forms: end feed fittings and integral solder and integral brazing ring fitting ends. The fittings are designed for a service lifetime up to fifty years.
The fittings are used up to the operating temperatures and corresponding maximum operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
The capillary fittings for soldering or brazing to copper tubes are used with solder alloys in accordance with alloys specified in EN ISO 9453 and brazing alloys in accordance with alloys specified in EN ISO 17672.
Adaptor fittings for use with copper tubes may combine capillary soldering or capillary brazing ends with fitting ends defined in the other parts of EN 1254.
Capillary fittings for soldering or brazing may also have flanged end connections according to EN 1092-3.
Capillary fittings for soldering or brazing may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845;
-   refrigeration systems;
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems;
-   medical gas systems according to EN ISO 7396;
-   refrigeration systems.

  • Standard
    27 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-2:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 2: Compression fittings for use with copper tubes
EN 1254-2:2021

This document specifies product characteristics, assessment methods, compliance criteria of the test results and a designation system for compression fittings for connecting with copper tubes. Compression fittings exist with sealing elements - metallic and/or non-metallic - called non manipulative (commonly referenced as type A) and without sealing elements, called manipulative (commonly referenced as type B). For the purposes of joining copper tubes, the fitting ends have a size range from 6 mm to 108 mm. The compression fittings are designed for a service lifetime up to fifty years.
The fittings are used up to the operating temperatures and maximum operating pressures as indicated in Annex A.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Compression fitting ends, Type A, are used with copper tubes to EN 1057 in all material hardness conditions.
NOTE 1   Compression fittings, Type A, will possibly require an internal support when used with R220 (annealed) copper tube and the manufacturer’s advice should be sought.
Compression fitting ends, Type B, are used with R220 (annealed) or R250 (half-hard) copper tube to EN 1057.
NOTE 2   Compression fittings, Type B, may be used with R290 (hard) copper tube and the manufacturer’s advice should be sought.
Adaptor fittings for use with copper tubes may combine compression ends with fitting ends defined in the other parts of EN 1254.
Compression fittings for use with copper tubes may also have flanged end connections according to EN 1092-3.
Compression fittings for use with copper tubes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845.
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-8:2021(Main)
Copper and copper alloys - Plumbing fittings - Part 8: Press fittings for use with plastics and multilayer pipes
EN 1254-8:2021

This document specifies product characteristics, assessment methods, compliance criteria and a designation system for fittings with radial and axial press ends for use with plastics and multilayer pipes. The fitting ends have a size range from 10 mm to 160 mm. The fittings are designed for a service lifetime up to fifty.
This document applies to copper alloy fittings. A non-exhaustive list of these copper alloys is given in CEN/TS 13388.
Adaptor fittings for use with plastic and multilayer pipes may combine press ends with fitting ends defined in the other parts of EN 1254.
Press fittings for use with plastic and multilayer pipes may also have flanged end connections according to EN 1092-3.
Press fittings for use with plastic and multilayer pipes may also have a plated or other decorative surface coating.
Fittings can be produced by machining, metal forming, casting, or fabrication.
Products covered by this standard are intended to be used in:
a)   liquid applications:
-   hot, cold or combined hot and cold water systems according to EN 806;
-   closed heating systems according to EN 12828 and cooling systems;
-   drainage systems;
-   sprinkler systems according to EN 12845;
b)   gas applications:
-   natural gas and liquefied petroleum gas systems with a maximum operating pressure less than or equal to 5 bar according to EN 1775;
-   compressed air systems.

  • Standard
    33 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1254-20:2021/oprA1:2024(Amendment)
Copper and copper alloys - Plumbing fittings - Part 20: Definitions, thread dimensions, test methods, reference data and supporting information
EN 1254-20:2021/prA1

This document contains definitions, thread dimension, reference data (minimum bore), supporting information (assembling instructions) and describes the test methods referenced by other parts of the EN 1254 series.
Thread dimensions comprise: wall thickness at threaded portions of fittings, dimensions of tail pipe ends for swivel fittings, dimensions of gas union connectors, thread dimensions and thread profile.
Test methods comprise: leak tightness under internal hydrostatic pressure, leak tightness under internal pneumatic pressure, integrity of fabricated fitting bodies or having an 'as cast' microstructure, resistance to pull out of joints to metallic tubes, resistance of joints with metallic tube to vibration, resistance of joints to static flexural force, leak tightness of joints under vacuum, the resistance of joints to temperature cycling, detecting non-pressed fitting ends, resistance to stress corrosion, detection of a carbon film on the surface of copper fittings, determination of mean depth of dezincification, resistance of joints to pressure cycling, disconnection and re-use, determining if the diameter and/or the length of engagement of a capillary end is/are within the specified tolerance, determining the minimum length of engagement of an integral solder or brazing ring socket having a formed groove.

  • Draft
    5 pages
    English language
    sale 10% off
    e-Library read for
    1 day