SIST EN 61300-2-7:2013

Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-7: Tests - Bending moment

This part of IEC 61300 details a procedure for determining the suitability of a fibre optic device to withstand the environmental condition of a bending moment which may occur in actual use, storage and/or transport. The test is primarily intended to permit the observation of effects of a bending moment. The bending moment may result in effects that would destroy functional utility, cause loss of physical strength, and cause changes in other important mechanical properties. Degradation of optical properties may also occur. The specimen may be a component, a connector set, a splice or other device combination intended for fibre optic usage.

Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und Messverfahren - Teil 2-7: Prüfungen - Biegemoment

Dispositifs d'interconnexion et composants passifs à fibres optiques - Procédures fondamentales d’essais et de mesures - Partie 2-7: Essais – Moment de flexion

La CEI 61300-2-7:2013 décrit une méthode destinée à déterminer l'aptitude d'un dispositif à fibres optiques à supporter des conditions environnementales dans lesquelles peut intervenir un moment de flexion en cours d'utilisation, de stockage et/ou de transport. Cet essai a pour principal objectif de permettre l'observation des effets d'un moment de flexion. Le moment de flexion peut provoquer des effets de nature à affecter de manière importante le bon fonctionnement, à provoquer une perte de résistance physique et à causer des modifications d'autres propriétés mécaniques importantes. Une dégradation des propriétés optiques peut également se produire. Le spécimen peut être un composant, un jeu de connecteurs, une épissure ou une autre combinaison de dispositifs destinée à être utilisée avec des fibres optiques. Cette deuxième édition annule et remplace la première édition parue en 1995. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente:  - un ré-examen complet de l'ensemble du document, y compris l'addition de nouvelles références normatives;  - la clarification du dispositif en essai (DUT);  - la clarification de la relation entre sévérités, les catégories de performance et le DUT. Mots clés: aptitude d'un dispositif à fibres optiques à supporter des conditions environnementales dans lesquelles peut intervenir un moment de flexion

Optični spojni elementi in pasivne komponente - Osnovni preskusni in merilni postopki - 2-7. del: Preskusi - Upogibni moment

V tem delu standarda IEC 61300 je podrobno opisan postopek za ugotavljanje primernosti naprav z optičnimi vlakni za odpornost proti okoljskemu pogoju upogibnega momenta, ki se lahko pojavi med dejanskim delovanjem, shranjevanjem in/ali transportom. Preskus je prvenstveno namenjen omogočanju opazovanja učinkov upogibnega momenta. Upogibni moment lahko uniči funkcionalnost ter povzroči izgubo fizične moči in spremembe drugih pomembnih mehanskih lastnosti. Tudi optične lastnosti se lahko poslabšajo. Vzorec je lahko komponenta, sklop konektorjev, spojnica ali druga kombinacija naprav, namenjena za uporabo z optičnimi vlakni.

General Information

• Status: Published
• Publication Date: 11-Sep-2013
• ICS: 33.180.20 - Fibre optic interconnecting devices
• Technical Committee: MOC - Mobile Communications
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 29-Aug-2013
• Due Date: 03-Nov-2013
• Completion Date: 12-Sep-2013
• Ref Project: EN 61300-2-7:2013 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-7: Tests - Bending moment

Relations

• Revised: SIST EN 61300-2-7:1999 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-7: Tests - Bending moment
• Effective Date: 29-Mar-2013
• Replaces: SIST EN 61300-2-7:1999 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-7: Tests - Bending moment
• Effective Date: 29-Jan-2023
• Revised: SIST EN 61300-2-7:1999 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-7: Tests - Bending moment
• Effective Date: 06-May-2014
• Replaces: SIST EN 61300-2-7:1999 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures -- Part 2-7: Tests - Bending moment
• Effective Date: 07-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN 61300-2-7:2013
01-oktober-2013
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHVNXVL8SRJLEQLPRPHQW
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-7: Tests - Bending moment
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-7: Prüfungen - Biegemoment
Ta slovenski standard je istoveten z: EN 61300-2-7:2013
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61300-2-7:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 61300-2-7:2013

---------------------- Page: 2 ----------------------

SIST EN 61300-2-7:2013

EUROPEAN STANDARD
EN 61300-2-7

NORME EUROPÉENNE
July 2013
EUROPÄISCHE NORM

ICS 33.180.20 Supersedes EN 61300-2-7:1997


English version


Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures -
Part 2-7: Tests -
Bending moment
(IEC 61300-2-7:2013)


Dispositifs d'interconnexion et composants Lichtwellenleiter -
passifs à fibres optiques - Verbindungselemente und passive
Procédures fondamentales d’essais et de Bauteile -
mesures - Grundlegende Prüf- und Messverfahren -
Partie 2-7: Essais - Moment de flexion Teil 2-7: Prüfungen -
(CEI 61300-2-7:2013) Biegemoment
(IEC 61300-2-7:2013)





This European Standard was approved by CENELEC on 2013-06-12. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the CEN-CENELEC Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the CEN-CENELEC Management Centre has the same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.

CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung

Management Centre: Avenue Marnix 17, B - 1000 Brussels


© 2013 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61300-2-7:2013 E

---------------------- Page: 3 ----------------------

SIST EN 61300-2-7:2013
EN 61300-2-7:2013 - 2 -

Foreword
The text of document 86B/3579A/FDIS, future edition 2 of IEC 61300-2-7, prepared by SC 86B, “Fibre
optic interconnecting devices and passive components”, of IEC TC 86, “Fibre optics” was submitted to the
IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-7:2013.
The following dates are fixed:
• latest date by which the document has (dop) 2014-03-12
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2014-06-12
• latest date by which the national
standards conflicting with the

document have to be withdrawn

This document supersedes EN 61300-2-7:1997.
EN 61300-2-7:2013 includes the following significant technical changes with respect to
EN 61300-2-7:1997:
a) a complete reconsideration of the entire document, including additional normative references;
b) clarification of the device under test (DUT);
c) clarification of the relationship between severities, performance categories and the DUT.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent
rights.
Endorsement notice
The text of the International Standard IEC 61300-2-7:2013 was approved by CENELEC as a European
Standard without any modification.

---------------------- Page: 4 ----------------------

SIST EN 61300-2-7:2013
- 3 - EN 61300-2-7:2013
Annex ZA
(normative)

Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.

NOTE  When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.

Publication Year Title EN/HD Year

IEC 61300-3-1 - Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -
Part 3-1: Examinations and measurements -
Visual examination


IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures -
Part 3-3: Examinations and measurements -
Active monitoring of changes in attenuation
and return loss


IEC 61300-3-4 - Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures -
Part 3-4: Examinations and measurements -
Attenuation

---------------------- Page: 5 ----------------------

SIST EN 61300-2-7:2013

---------------------- Page: 6 ----------------------

SIST EN 61300-2-7:2013



IEC 61300-2-7

®


Edition 2.0 2013-05




INTERNATIONAL



STANDARD




NORME



INTERNATIONALE











Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –

Part 2-7: Tests – Bending moment




Dispositifs d'interconnexion et composants passifs à fibres optiques –

Procédures fondamentales d’essais et de mesures –


Partie 2-7: Essais – Moment de flexion












INTERNATIONAL

ELECTROTECHNICAL

COMMISSION


COMMISSION

ELECTROTECHNIQUE

PRICE CODE
INTERNATIONALE

CODE PRIX K


ICS 33.180.20 ISBN 978-2-83220-790-1



Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 61300-2-7:2013
– 2 – 61300-2-7 © IEC:2013
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 General description . 5
4 Apparatus . 5
4.1 Design for a 1 piece or 3 piece DUT . 5
4.2 Design for a 2 piece DUT . 6
4.3 Optical measurements . 7
5 Procedure. 7
5.1 Preconditioning . 7
5.2 Initial examinations and measurements . 7
5.3 Conditioning for a 1 piece or 3 piece DUT . 7
5.4 Conditioning for a 2 piece DUT . 7
5.5 Recovery . 8
5.6 Final examinations and measurements . 8
6 Severity . 8
7 Details to be specified . 9
Annex A (informative) Example for a bending moment test method for splices . 10

Figure 1 – Test apparatus to apply a bending moment to a 1 piece or 3 piece DUT. 6
Figure 2 – Test apparatus to apply a bending moment to a 2 piece DUT . 7
Figure A.1 – Example for a bending moment test set-up for splices . 10

Table 1 – Relationship between severities, performance categories and DUT . 8
Table 2 – Severities for an 1 piece or 3 piece DUT . 9
Table 3 – Severities for an 2 piece DUT . 9

---------------------- Page: 8 ----------------------

SIST EN 61300-2-7:2013
61300-2-7 © IEC:2013 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________

FIBRE OPTIC INTERCONNECTING DEVICES
AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-7: Tests – Bending moment

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, se
...