Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 2: Tolerances on dimensions and form

This part prEN 12020 specifies the tolerances on dimensions and form of extruded precision profiles, in alloys EN AW-6060 and EN AW-6063 manufactured with and without a thermal barrier (see figures 1 and 2). This applies to as extruded products supplied without further surface treatment.

Aluminium und Aluminiumlegierungen - Stranggepresste Präzisionsprofile aus Legierungen EN AW-6060 und EN AW-6063 - Teil 2: Grenzabmaße und Formtoleranzen

Dieser Teil von EN 12020 legt die Grenzabmaße und Formtoleranzen für stranggepreßte Präzisionsprofile aus den Legierungen EN AW-6060 und EN AW-6063, die mit oder ohne Wärmedämmung (siehe Bild 1 bzw. Bild 2) hergestellt werden, fest. Er gilt für stranggepreßte Erzeugnisse, die ohne weitere Oberflächenbehandlung hergestellt werden.Die Präzisionsprofile, die Gegenstand dieser Norm sind, unterscheiden sich von den stranggepressten Profilen für allgemeine Anwendungen nach EN 755-9 wie folgt:
- sie sind hauptsächlich für Anwendungen im Architekturbereich vorgesehen;
- sie entsprechen strengeren Anforderungen im Hinblick auf den Zustand der sichtbaren Oberflächen;
- der maximale Durchmesser des Umschlingungskreises CD ist 300mm;
- sei weisen engere Grendzabmaße und Formtoleranzen auf.
Bei Profilen, die aufgrund ihrer komplexen Konstruktion schwierig herzustellen und zu spezifizieren sind, können besondere Vereinbarungen zwischen Kunden und Hersteller notwendig sein.

Aluminium et alliages d'aluminium - Profilés de précision filés en alliages EN AW-6060 et EN AW-6063 - Partie 2: Tolérances sur dimensions et forme

La présent partie de la norme EN 12020 spécifie les tolérances sur dimensions et forme des profilés filés de précision en alliages EN AW-6060 et EN AW-6063 fabriqués avec ou sans barriere thermique (voir Figures 1 et 2). Elle s'applique aux produits filés fournis sans traitement de surface spécifique. Les profilés de précision couverts dans cette norme sont distincts des produits filés pour application générale couverts dans l'EN 755-9 par les caractéristiques suivantes :
3 ils sont principalement destinés pour applications architecturales ;
3 ils rencontrent des exigences plus rigoureuses en ce qui concerne l'état de surface des surfaces visibles ;
3 le diametre du cercle circonscrit CD est de 300 mm ;
3 ils sont fabriqués avec des tolérances sur les dimensions et forme plus serrées.
Dans le cas de profilés lesquels, en raison de la complexité de leurs dessins, sont difficiles a fabriquer et a spécifier, des accords spéciaux entre acheteur et fabricant sont a rechercher.
NOTE 1   Le matériau de barriere thermique n'est pas couvert par cette norme.
NOTE 2   Des produits cités dans la présente norme peuvent faire l'objet de brevet ou de demandes de brevets, et leur inclusion dans la présente norme ne doit en aucune façon considérée comme l'attribution d'une licence au regard des droits attachés a de tels brevets.
Le CEN/TC 132 confirme que dans le cas ou le détenteur d'un brevet refuse de céder des licences sur les produits normalisés sous des conditions raisonnables et non discriminatoires, alors ce produit serait éliminé de la norme correspondante

Aluminij in aluminijeve zlitine - Precizni iztiskani profili v zlitinah EN AW-6060 in EN AW-6063 - 2. del: Odstopki mer in tolerance oblike

General Information

Status
Withdrawn
Publication Date
31-Jan-2002
Withdrawal Date
03-Apr-2008
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
28-Mar-2008
Due Date
20-Apr-2008
Completion Date
04-Apr-2008

Relations

Buy Standard

Standard
EN 12020-2:2002
English language
14 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Aluminium and aluminium alloys - Extruded precision profiles in alloys EN AW-6060 and EN AW-6063 - Part 2: Tolerances on dimensions and formAluminij in aluminijeve zlitine - Precizni iztiskani profili v zlitinah EN AW-6060 in EN AW-6063 - 2. del: Odstopki mer in tolerance oblikeAluminium et alliages d'aluminium - Profilés de précision filés en alliages EN AW-6060 et EN AW-6063 - Partie 2: Tolérances sur dimensions et formeAluminium und Aluminiumlegierungen - Stranggepresste Präzisionsprofile aus Legierungen EN AW-6060 und EN AW-6063 - Teil 2: Grenzabmaße und FormtoleranzenTa slovenski standard je istoveten z:EN 12020-2:2001SIST EN 12020-2:2002en77.150.10ICS:SLOVENSKI
STANDARDSIST EN 12020-2:200201-februar-2002







EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12020-2April 2001ICS 77.150.10English versionAluminium and aluminium alloys - Extruded precision profiles inalloys EN AW-6060 and EN AW-6063 - Part 2: Tolerances ondimensions and formAluminium et alliages d'aluminium - Profilés de précisionfilés en alliages EN AW-6060 et EN AW-6063 - Partie 2:Tolérances sur dimensions et formeAluminium und Aluminiumlegierungen - StranggepresstePräzisionsprofile aus Legierungen EN AW-6060 und ENAW-6063 - Teil 2: Grenzabmaße und FormtoleranzenThis European Standard was approved by CEN on 18 February 2001.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2001 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12020-2:2001 E



Page 2EN 12020-2:2001ContentsPageForeword.31Scope.42Tolerances on dimensions.52.1General.52.2Cross-sectional dimensions.52.3Length.72.4Squareness of cut ends.72.5Length offset for profiles with a thermal barrier.83Tolerance on form.83.1Straightness.83.2Convexity - Concavity.93.3Contour.103.4Twist.103.5Angularity.123.6Corner and fillet radii.13



Page 3EN 12020-2:2001ForewordThis European Standard has been prepared by Technical Committee CEN/TC 132 "Aluminium and aluminiumalloys", the secretariat of which is held by AFNOR.This European Standard shall be given the status of a national standard, either by publication of an identical text orby endorsement, at the latest by October 2001, and conflicting national standards shall be withdrawn at the latestby October 2001.Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG5 "Extruded anddrawn products" to prepare the following standard :EN 12020-2, Aluminium and aluminium alloys – Extruded precision profiles in alloys
EN
AW-6060 andEN AW-6063 – Part 2 : Tolerances on dimensions and form.This standard is part of a set of two standards. The other standard deals with :EN 12020-1, Aluminium and aluminium alloys – Extruded precision profiles in alloys
EN
AW-6060 andEN AW-6063 – Part 1: Technical conditions for inspection and delivery.According to the CEN/CENELEC Internal Regulations, the national standards organizations of the followingcountries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland,France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden,Switzerland and the United Kingdom.



Page 4EN 12020-2:20011 ScopeThis part of EN 12020 specifies tolerances on dimensions and form of extruded precision profiles, in alloysEN AW-6060 and EN AW-6063 manufactured with and without a thermal barrier (see Figures 1 and 2). It applies toas extruded products supplied without further surface treatment. Precision profiles covered in this standard aredistinguished from extruded profiles for general applications covered in EN 755-9 by the following characteristics : they are mainly for architectural applications ; they meet more stringent requirements regarding the surface condition of visible surfaces ; the maximum diameter of the circumscribing circle CD is 300 mm ; they are made to closer tolerances on dimensions and form.In the case of profiles which, due to the complexity of their design, are difficult to manufacture and specify, thenspecial agreements between purchaser and manufacturer may need to be reached.NOTE 1The thermal barrier material is not covered by this standard.NOTE 2Some of the products listed in the present standard can be subject to patent or patent applications, and their listingherein does not in any way imply the granting of a licence under such patent right.CEN/TC 132 affirms it is its policy that in the case when a patentee refuses to grant licences on standardised standard productsunder reasonable and not discriminatory conditions then this product shall be removed from the corresponding standard.Dimensions in millimetresKey1Thermal barrierFigure 1 — Profile without thermal barrier(example)Figure 2 — Profile with thermal barrier(example)



Page 5EN 12020-2:20012 Tolerances on dimensions2.1 GeneralIf, for compelling reasons, tolerances closer than those specified in 2.2.1 and 2.2.2 are required, these shall only bespecified for dimensions that are critical to the function, subject to particular agreement. Any such reduction shallnot exceed two-thirds of the values specified in this standard and is subject to a minimum tolerance band of0,3 mm.2.2 Cross-secti
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.