oSIST prEN ISO 877-2:2016

Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO/DIS 877-2:2016)

WI abandoned to follow ISO decision to cancel the corresponding project.

Kunststoffe - Freibewitterung - Teil 2: Bewitterung und Bestrahlen hinter Fensterglas (ISO/DIS 877-2:2016)

Dieser Teil von ISO 877 legt ein Verfahren für die direkte Beanspruchung von Kunststoffen durch die Sonnen¬strahlung (Verfahren A) und ein Verfahren für die Beanspruchung von Kunststoffen hinter Fenster-glas (Verfahren B) fest. Das Ziel ist es, die Eigenschaftsänderungen, die nach bestimmten Stufen derartiger Beanspruchungen eintreten, zu beurteilen. Eine allgemeine Anleitung, die den Anwendungsbereich von ISO 877 betrifft, ist in ISO/DIS 877 1:2016, Abschnitt 1, angegeben.

Plastiques - Méthodes d'exposition au rayonnement solaire - Partie 2: Exposition directe et exposition derrière une vitre en verre (ISO/DIS 877-2:2016)

Polimerni materiali - Metode izpostavitve vremenskim vplivom - 2. del: Vremenski vplivi z dnevno svetlobo, filtrirano skozi steklo (ISO/DIS 877-2:2016)

General Information

• Status: Not Published
• Public Enquiry End Date: 25-Oct-2016
• ICS: 83.080.01 - Plastics in general
• Technical Committee: IPMA - Polimer materials and products
• Current Stage: 98 - Abandoned project (Adopted Project)
• Start Date: 13-Jan-2020
• Due Date: 18-Jan-2020
• Completion Date: 13-Jan-2020
• Ref Project: prEN ISO 877-2 - Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO/DIS 877-2:2016)

Relations

• Revised: SIST EN ISO 877-2:2012 - Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO 877-2:2009)
• Effective Date: 15-Oct-2014
• Revised: SIST EN ISO 877-2:2012 - Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO 877-2:2009)
• Effective Date: 18-Jan-2023
• Revised: SIST EN ISO 877-2:2012 - Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and exposure behind window glass (ISO 877-2:2009)
• Effective Date: 19-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN ISO 877-2:2016
01-oktober-2016
Polimerni materiali - Metode izpostavitve vremenskim vplivom - 2. del: Vremenski
vplivi z dnevno svetlobo, filtrirano skozi steklo (ISO/DIS 877-2:2016)
Plastics - Methods of exposure to solar radiation - Part 2: Direct weathering and
exposure behind window glass (ISO/DIS 877-2:2016)
Kunststoffe - Freibewitterung - Teil 2: Bewitterung und Bestrahlen hinter Fensterglas
(ISO/DIS 877-2:2016)
Plastiques - Méthodes d'exposition au rayonnement solaire - Partie 2: Exposition directe
et exposition derrière une vitre en verre (ISO/DIS 877-2:2016)
Ta slovenski standard je istoveten z: prEN ISO 877-2
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO 877-2:2016 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN ISO 877-2:2016

---------------------- Page: 2 ----------------------
oSIST prEN ISO 877-2:2016
DRAFT INTERNATIONAL STANDARD
ISO/DIS 877-2
ISO/TC 61/SC 6 Secretariat: DIN
Voting begins on: Voting terminates on:
2016-08-03 2016-10-25
Plastics — Methods of exposure to solar radiation —
Part 2:
Direct weathering and exposure behind window glass
Plastiques — Méthodes d’exposition au rayonnement solaire —
Partie 2: Exposition directe et exposition derrière une vitre en verre
ICS: 83.080.01
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 877-2:2016(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2016

---------------------- Page: 3 ----------------------
oSIST prEN ISO 877-2:2016
ISO/DIS 877-2:2016(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2016, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2016 – All rights reserved

---------------------- Page: 4 ----------------------
oSIST prEN ISO 877-2:2016
ISO/DIS 877-2:2016(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Principle . 1
4 Apparatus . 1
4.1 General requirements . 1
4.2 Test fixture for exposures using method A . 1
4.3 Test fixture for exposures using method B . 2
4.4 Apparatus for measurement of climatic factors . 3
5 Test specimens. 3
6 Conditions of exposure of the test specimens . 4
6.1 Exposure aspect . 4
6.2 Exposure site . 4
7 Exposure stages . 4
7.1 General . 4
7.2 Duration of exposure . 4
7.3 Solar radiant exposure . 4
8 Procedure. 5
8.1 Mounting of test specimens . 5
8.1.1 General. 5
8.1.2 Method A . 5
8.1.3 Method B . 5
8.2 Mounting of reference materials (if used) . 5
8.3 Climatic observations . 5
8.4 Exposure of test specimens . 5
8.4.1 General. 5
8.4.2 Method A . 5
8.4.3 Method B . 5
8.5 Determination of changes in properties . 5
9 Expression of results . 6
9.1 Determination of changes in properties . 6
9.2 Climatic conditions . 6
10 Test report . 6
© ISO 2016 – All rights reserved iii

---------------------- Page: 5 ----------------------
oSIST prEN ISO 877-2:2016
ISO/DIS 877-2:2016(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO’s adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www.iso.org/iso/foreword.html.
The committee responsible for this document is ISO/TC 61/SC 6.
This second edition cancels and replaces the first edition (ISO 877-2:2009), which has been technically
revised.
ISO 877 consists of the following parts.
— Part 1: General guidance
— Part 2: Direct weathering and exposure behind window glass
— Part 3: Intensified weathering using concentrated solar radiation
iv © ISO 2016 – All rights reserved

---------------------- Page: 6 ----------------------
oSIST prEN ISO 877-2:2016
DRAFT INTERNATIONAL STANDARD ISO/DIS 877-2:2016(E)
Plastics — Methods of exposure to solar radiation —
Part 2:
Direct weathering and exposure behind window glass
1 Scope
This part of ISO 877 specifies a method for the direct exposure of plastics to solar radiation (method A)
and a method for the exposure of plastics to glass-filtered solar radiation (exposure behind window
gla
...