Acoustics - Laboratory and field measurement of flanking transmission for airborne, impact and building service equipment sound between adjoining rooms - Part 3: Application to Type B elements when the junction has a substantial influence (ISO 10848-3:2017)

ISO 10848 (all parts) specifies measurement methods to characterize the flanking transmission of one
or several building components.
This document specifies laboratory and field measurements of buildings for Type B elements (defined
in ISO 10848-1) when the junction has a substantial influence.
Laboratory measurements are used to quantify the performance of the junction with suppressed
flanking transmission from the laboratory structure. Field measurements are used to characterize
the in situ performance and it is not usually possible to suppress unwanted flanking transmission
sufficiently; hence, the results can only be considered representative of the performance of that junction
when installed in that particular building structure.
This document is referred to in ISO 10848-1:2017, 4.5 as being a supporting part to the frame document
and applies to Type B elements that are structurally connected as defined in ISO 10848-1.
The measured quantities can be used to compare different products, or to express a requirement, or as
input data for prediction methods, such as ISO 12354-1 and ISO 12354-2.
The relevant quantity to be measured is selected according to ISO 10848-1:2017, 4.5. The performance
of the building components is expressed either as an overall quantity for the combination of elements
and junction (such as Dn,f,ij and/or Ln,f,ij and/or Lne0,f,ij) or as the normalized direction-average velocity
level difference Dv,ij,n of a junction. Dn,f,ij, Ln,f,ij, Lne0,f,ij and Dv,ij,n depend on the actual dimensions of
the elements.

Akustik - Messung der Flankenübertragung von Luftschall, Trittschall und Schall von Gebäudetechnischen Anlagen zwischen benachbarten Räumen im Prüfstand und am Bau - Teil 3: Anwendung auf Typ B-Bauteile, wenn die Verbindung wesentlichen Einfluss hat (ISO 10848-3:2017)

ISO 10848 legt Messverfahren zur Bestimmung der Flankenübertragung eines oder mehrerer Bauteile fest, die in dafür ausgelegten Prüfständen oder am Bau durchzuführen sind.
Dieser Teil von ISO 10848 legt Prüfstands- und Messungen am Bau von Gebäuden für Typ-B-Bauteile (in ISO 10848 1 definiert) fest, wenn die Stoßstelle wesentlichen Einfluss hat.
Prüfstandsmessungen werden zur Quantifizierung der Stoßstelleneigenschaften in Bezug auf unterdrückte Flankenübertragung von der Prüfstandkonstruktion verwendet. Messungen am Bau werden zur Charakterisierung der Eigenschaften im Einbauzustand verwendet, wobei die Unterdrückung unerwünschter Flankenübertragung üblicherweise nicht möglich ist. Daher können die Ergebnisse lediglich für die Eigenschaften der vorliegenden Stoßstelle im vorliegenden Gebäude als repräsentativ angesehen werden.
Dieser Teil der ISO 10848 ist in ISO 10848 1, 4.5, als unterstützender Teil zum Rahmendokument referenziert und gilt für Typ-B-Bauteile, die gemäß der Definition in ISO 10848 1 baulich verbunden sind.
Die gemessenen Größen können für den Vergleich unterschiedlicher Produkte oder für die Formulierung einer Anforderung oder als Eingangsdaten für Vorhersageverfahren wie ISO 12354 1 und ISO 12354 2 herangezogen werden.
Die entsprechende zu messende Größe wird nach ISO 10848 1, 4.5 ausgewählt. Die Gebrauchstauglichkeit der Bauteile wird entweder als Gesamtgröße für die Kombination von Bauteilen und Stoßstelle (z. B. Dn,f,ij und/oder Ln,f,ij und/oder Lne0,f,ij) oder als richtungsgemittelte Norm-Schnellepegeldifferenz (D_(v"," ij"," n) ) ̅ einer Stoßstelle angegeben. Dn,f,ij, Ln,f,ij, Lne0,f,ij und (D_(v"," ij"," n) ) ̅ hängen von den tatsächlichen Maßen der Bauteile ab.

Acoustique - Mesurage en laboratoire des transmissions latérales du bruit aérien et des bruits de choc entre des pièces adjacentes - Partie 3: Application aux éléments de Type B lorsque la jonction a une influence importante (ISO 10848-3:2017)

L'ISO 10848 (toutes les parties) spécifie les méthodes de mesure pour la caractérisation des transmissions latérales d'un ou de plusieurs éléments de construction.
Le présent document spécifie les mesurages en laboratoire et les mesurages sur site des bâtiments pour les éléments de type B (définis dans l'ISO 10848‑1) lorsque la jonction a une influence importante.
Les mesurages en laboratoire sont utilisés pour quantifier la performance de la jonction avec suppression des transmissions latérales de la structure du laboratoire. Les mesurages sur site sont utilisés pour caractériser la performance in situ et il n'est généralement pas possible de supprimer suffisamment les transmissions latérales parasites; les résultats ne peuvent donc être considérés comme représentatifs de la performance de cette jonction que si elle est installée dans cette structure de bâtiment particulière.
L'ISO 10848‑1:2017, 4.5 fait référence au présent document, qui vient à l'appui du document cadre et s'applique aux éléments de type B structurellement couplés comme définis dans l'ISO 10848‑1.
Les grandeurs mesurées peuvent être utilisées pour comparer différents produits, pour exprimer une exigence ou comme données d'entrée des méthodes de prévision telles que l'ISO 12354‑1 et l'ISO 12354‑2.
La grandeur pertinente à mesurer est choisie conformément à l'ISO 10848‑1:2017, 4.5. Les performances des éléments de construction sont exprimées en tant que grandeur globale pour la combinaison des éléments et de la jonction (telle que Dn,f,ij et/ou Ln,f,ij et/ou Lne0,f,ij) ou en tant qu'isolement vibratoire bidirectionnel normalisé  d'une jonction. Dn,f,ij, Ln,f,ij, Lne0,f,ij et  dépendent des dimensions réelles des éléments.

Akustika - Laboratorijsko in terensko merjenje bočnega prenosa zvoka v zraku, udarnega zvoka in zvoka v gradbenih elementih servisne opreme med mejnimi prostori - 3. del: Uporaba elementov tipa B pri pomembnem vplivu stikov (ISO 10848-3:2017)

ISO 10848 (vsi deli) določa merilne metode za opredelitev bočnega prenosa pri enem
ali več sestavnih delih stavb.
Ta dokument določa laboratorijske in terenske meritve elementov stavb tipa B (določenih
v standardu ISO 10848-1) pri pomembnem vplivu stikov.
Laboratorijske meritve se uporabljajo za kvantifikacijo lastnosti stika z majhnim bočnim prenosom iz laboratorijske konstrukcije. Terenske meritve se uporabljajo za opredelitev lastnosti na mestu uporabe, neželenega bočnega prenosa pa običajno ni mogoče zadosti zmanjšati; rezultate je mogoče šteti za reprezentativne samo za prikaz lastnosti stika v primeru namestitve v zadevni stavbni konstrukciji.
Ta dokument je naveden v standardu ISO 10848-1:2017, 4.5 kot podporni del okvirnega dokumenta in se uporablja za elemente tipa B, ki so strukturno povezani, kot je opredeljeno v ISO 10848-1.
Izmerjene količine je mogoče uporabiti za primerjavo različnih proizvodov, za izražanje zahteve ali kot vhodne podatke za metode napovedovanja (npr. ISO 12354-1 in ISO 12354-2).
Ustrezna količina, ki jo je treba izmeriti, je izbrana v skladu s standardom ISO 10848-1:2017, 4.5. Učinkovitost sestavnih delov stavb je izražena kot skupna količina za kombinacijo elementov in spoja (na primer Dn,f,ij in/ali Ln,f,ij in/ali Lne0,f,ij) ali normirana hitrostno povprečna razlika Dv,ij,n v ravni vibracij spoja. Količine Dn,f,ij, Ln,f,ij, Lne0,f,ij in Dv,ij,n so odvisne od dejanskih dimenzij elementov.

General Information

Status
Published
Public Enquiry End Date
09-Dec-2016
Publication Date
19-Mar-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-Nov-2017
Due Date
14-Jan-2018
Completion Date
20-Mar-2018

Relations

Buy Standard

Standard
EN ISO 10848-3:2018
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10848-3:2018
01-april-2018
1DGRPHãþD
SIST EN ISO 10848-3:2006
$NXVWLND/DERUDWRULMVNRLQWHUHQVNRPHUMHQMHERþQHJDSUHQRVD]YRNDY]UDNX
XGDUQHJD]YRNDLQ]YRNDYJUDGEHQLKHOHPHQWLKVHUYLVQHRSUHPHPHGPHMQLPL
SURVWRULGHO8SRUDEDHOHPHQWRYWLSD%SULSRPHPEQHPYSOLYXVWLNRY ,62

Acoustics - Laboratory and field measurement of flanking transmission for airborne,
impact and building service equipment sound between adjoining rooms - Part 3:
Application to Type B elements when the junction has a substantial influence (ISO 10848
-3:2017)
Akustik - Messung der Flankenübertragung von Luftschall, Trittschall und Schall von
Gebäudetechnischen Anlagen zwischen benachbarten Räumen im Prüfstand und am
Bau - Teil 3: Anwendung auf Typ B-Bauteile, wenn die Verbindung wesentlichen Einfluss
hat (ISO 10848-3:2017)
Acoustique - Mesurage en laboratoire des transmissions latérales du bruit aérien et des
bruits de choc entre des pièces adjacentes - Partie 3: Application aux éléments de Type
B lorsque la jonction a une influence importante (ISO 10848-3:2017)
Ta slovenski standard je istoveten z: EN ISO 10848-3:2017
ICS:
17.140.01 $NXVWLþQDPHUMHQMDLQ Acoustic measurements and
EODåHQMHKUXSDQDVSORãQR noise abatement in general
91.120.20 $NXVWLNDYVWDYEDK=YRþQD Acoustics in building. Sound
L]RODFLMD insulation
SIST EN ISO 10848-3:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10848-3:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 10848-3:2018


EN ISO 10848-3
EUROPEAN STANDARD

NORME EUROPÉENNE

October 2017
EUROPÄISCHE NORM
ICS 91.120.20 Supersedes EN ISO 10848-3:2006
English Version

Acoustics - Laboratory and field measurement of flanking
transmission for airborne, impact and building service
equipment sound between adjoining rooms - Part 3:
Application to Type B elements when the junction has a
substantial influence (ISO 10848-3:2017)
Acoustique - Mesurage en laboratoire et sur le terrain Akustik - Messung der Flankenübertragung von
des transmissions latérales du bruit aérien, des bruits Luftschall, Trittschall und Schall von
de choc et du bruit d'équipement technique de Gebäudetechnischen Anlagen zwischen benachbarten
bâtiment entre des pièces - Partie 3: Application aux Räumen im Prüfstand und am Bau - Teil 3: Anwendung
éléments de Type B lorsque la jonction a une influence auf Typ B-Bauteile, wenn die Verbindung wesentlichen
importante (ISO 10848-3:2017) Einfluss hat (ISO 10848-3:2017)
This European Standard was approved by CEN on 2 August 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10848-3:2017 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10848-3:2018
EN ISO 10848-3:2017 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 10848-3:2018
EN ISO 10848-3:2017 (E)
European foreword
This document (EN ISO 10848-3:2017) has been prepared by Technical Committee ISO/TC 43
"Acoustics" in collaboration with Technical Committee CEN/TC 126 “Acoustic properties of building
elements and of buildings” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2018 and conflicting national standards shall be
withdrawn at the latest by April 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10848-3:2006.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 10848-3:2017 has been approved by CEN as EN ISO 10848-3:2017 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 10848-3:2018

---------------------- Page: 6 ----------------------

SIST EN ISO 10848-3:2018
INTERNATIONAL ISO
STANDARD 10848-3
Second edition
2017-09
Acoustics — Laboratory and field
measurement of flanking transmission
for airborne, impact and building
service equipment sound between
adjoining rooms —
Part 3:
Application to Type B elements
when the junction has a substantial
influence
Acoustique — Mesurage en laboratoire et sur le terrain des
transmissions latérales du bruit aérien, des bruits de choc et du bruit
d’équipement technique de bâtiment entre des pièces —
Partie 3: Application aux éléments de Type B lorsque la jonction a une
influence importante
Reference number
ISO 10848-3:2017(E)
©
ISO 2017

---------------------- Page: 7 ----------------------

SIST EN ISO 10848-3:2018
ISO 10848-3:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 10848-3:2018
ISO 10848-3:2017(E)

Contents  Page
Foreword .iv
1  Scope . 1
2  Normative references . 1
3  Terms and definitions . 2
4  Instrumentation . 3
5  Test arrangement . 3
5.1 Requirements for the laboratory . 3
5.2 Requirements for a building structure in the field situation . 4
5.3 Installation of the test junction . 4
5.4 Shielding technique . 4
6  Test procedures . 4
7  Precision . 5
8  Expression of results . 5
9  Test report . 6
Annex A (informative) Measurement of D and L and L  with sound intensity .7
n,f,ij,I n,f,ij,I ne0,f,ij,I
Bibliography . 8
© ISO 2017 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 10848-3:2018
ISO 10848-3:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 43, Acoustics, Subcommittee SC 2, Building
acoustics.
This second edition cancels and replaces the first edition (ISO 10848-3:2006), which has been
technically revised with the following changes:
a) extension to field measurements;
b) extension to building service equipment with the introduction of the normalized flanking
equipment sound pressure level;
c) normalized direction-averaged vibration level difference for junctions between lightweight
elements has been introduced.
A list of all the parts in the ISO 10848 series can be found on the ISO website.
iv © ISO 2017 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 10848-3:2018
INTERNATIONAL STANDARD ISO 10848-3:2017(E)
Acoustics — Laboratory and field measurement of flanking
transmission for airborne, impact and building service
equipment sound between adjoining rooms —
Part 3:
Application to Type B elements when the junction has a
substantial influence
1  Scope
ISO 10848 (all parts) specifies measurement methods to characterize the flanking transmission of one
or several building components.
This document specifies laboratory and field measurements of buildings for Type B elements (defined
in ISO 10848-1) when the junction has a substantial influence.
Laboratory measurements are used to quantify the performance of the junction with suppressed
flanking transmission from the laboratory structure. Field measurements are used to characterize
the in situ performance and it is not usually possible to suppress unwanted flanking transmission
sufficiently; hence, the results can only be considered representative of the performance of that junction
when installed in that particular building structure.
This document is referred to in ISO 10848-1:2017, 4.5 as being a supporting part to the frame document
and applies to Type B elements that are structurally connected as defined in ISO 10848-1.
The measured quantities can be used to compare different products, or to express a requirement, or as
input data for prediction methods, such as ISO 12354-1 and ISO 12354-2.
The relevant quantity to be measured is selected according to ISO 10848-1:2017, 4.5. The performance
of the building components is expressed either as an overall quantity for the combination of elements
and junction (such as D and/or L and/or L ) or as the normalized direction-average velocity
n,f,ij n,f,ij ne0,f,ij
level difference D of a junction. D , L , L and D depend on the actual dimensions of
n,f,ij n,f,ij ne0,f,ij
vn,,ij vn,,ij
the elements.
2  Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 717-1, Acoustics — Rating of sound insulation in buildings and of building elements — Part 1: Airborne
sound insulation
ISO 717-2, Acoustics — Rating of sound insulation in buildings and of building elements — Part 2: Impact
sound insulation
ISO 10848-1:2017, Acoustics — Laboratory and field measurement of flanking transmission for airborne,
impact and building service equipment sound between adjoining rooms — Part 1: Frame document
ISO 12999-1, Acoustics — Determination and application of measurement uncertainties in building
acoustics — Part 1: Sound insulation
© ISO 2017 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 10848-3:2018
ISO 1
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.