iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 15316-4-2:2018/AC:2018

(Corrigendum)

Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2

Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2

Energetische Bewertung von Gebäuden - Verfahren zur Berechnung der Energieanforderungen und Nutzungsgrade der Anlagen - Teil 4-2: Wärmeerzeugung für die Raumheizung, Wärmepumpensysteme, Modul M3-8-2, M8-8-2

Performance énergétique des bâtiments - Méthode de calcul des besoins énergétiques et des rendements des systèmes - Partie 4-2 : Systèmes de génération de chauffage des locaux, systèmes de pompes à chaleur Module M3-8-2, M8-8-2

Energijske lastnosti stavb - Metoda za izračun energijskih zahtev in učinkovitosti sistema - 4-2. del: Sistemi za pridobivanje toplote za ogrevanje, toplotne črpalke - Modula M3-8-2 in M8-8-2 - Popravek AC

General Information

Status
Published
Publication Date
17-Apr-2018
ICS
27.080 - Heat pumps
91.140.10 - Central heating systems
Technical Committee
OGS - Heating for buildings
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
06-Feb-2018
Due Date
13-Apr-2018
Completion Date
18-Apr-2018
Directive
2010/31/EU - Directive 2010/31/eu of the European Parliament and of the Council of 19 May 2010 on the energy performance of buildings (recast)
Mandate
M/480 - Mandate to CEN, CENELEC and ETSI for the elaboration and adoption of standards for a methodology calculating the integrated energy performance of buildings and promoting the energy efficiency of buildings, in accordance with the terms set in the recast of the Directive on the energy performance buildings (2010/31/EU)
Ref Project
EN 15316-4-2:2017/AC:2017 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2

Relations

Revised
oSIST prEN 15316-4-2:2022 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
Effective Date
12-May-2021
Corrects
SIST EN 15316-4-2:2018 - Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
Effective Date
08-Jun-2022

Buy Standard

EN 15316-4-2:2018/AC:2018EN 15316-4-2:2018/AC:2018
PreviousNext
Corrigendum
EN 15316-4-2:2018/AC:2018
English language
3 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Energetische Bewertung von Gebäuden - Verfahren zur Berechnung der Energieanforderungen und Nutzungsgrade der Anlagen - Teil 4-2: Wärmeerzeugung für die Raumheizung, Wärmepumpensysteme, Modul M3-8-2, M8-8-2Performance énergétique des bâtiments - Méthode de calcul des besoins énergétiques et des rendements des systèmes - Partie 4-2 : Systèmes de génération de chauffage des locaux, systèmes de pompes à chaleur Module M3-8-2, M8-8-2Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-291.140.10Sistemi centralnega ogrevanjaCentral heating systems27.080Heat pumpsICS:Ta slovenski standard je istoveten z:EN 15316-4-2:2017/AC:2017SIST EN 15316-4-2:2018/AC:2018en01-maj-2018SIST EN 15316-4-2:2018/AC:2018SLOVENSKI
STANDARD



SIST EN 15316-4-2:2018/AC:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 15316-4-2:2017/AC
October 2017
ICS 91.140.10 English version
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
Performance énergétique des bâtiments - Méthode de calcul des besoins énergétiques et des rendements des systèmes - Partie 4-2 : Systèmes de génération de chauffage des locaux, systèmes de pompes à chaleur Module M3-8-2, M8-8-2
Energetische Bewertung von Gebäuden - Verfahren zur Berechnung der Energieanforderungen und Nutzungsgrade der Anlagen - Teil 4-5: Fernwärme und Fernkälte, Modul M3-8-5, M4-8-5, M8-8-5, M11-8-5 This c
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST-TP CEN/TR 15316-6-5:2018(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-5: Explanation and justification of EN 15316-4-2, Module M3-8
CEN/TR 15316-6-5:2017

This Technical Report (CEN/TR 15316-6-5) specifies details for EN 15316-4-2 and gives additional information for the application of EN 15316-4-2.

  • Technical report
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15316-4-2:2018(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
EN 15316-4-2:2017

The standard covers heat pumps for space heating, heat pump water heaters (HPWH) and heat pumps with combined space heating and domestic hot water production in alternate or simultaneous operation, where the same heat pump delivers the heat to cover the space heating and domestic hot water heat requirement.
The standard provides a calculation method under steady conditions that corresponds to one calculation step.
The results of this calculation are incorporated in larger building models and take in account the influence of the external conditions and building control that influence the energy requirements for heating supplied by the heat pump system.
The scope of this part is to standardise the:
-   required inputs;
-   calculation methods;
-   required outputs
for output thermal power generation for space heating and domestic hot water production of the following heat pump systems, including control:
-   electrically-driven vapour compression cycle (VCC) heat pumps;
-   combustion engine-driven vapour compression cycle heat pumps;
-   thermally-driven vapour absorption cycle (VAC) heat pumps,
using combinations of heat source and heat distribution listed in Table 1.
This standard does not cover sizing or inspection of heat pumps.
This standard deals with heat generators for heating or for combined domestic hot water and heating service. Generators for domestic hot water only are taken into account into module M8-8.
NOTE 1   Heat pumps generators for cooling systems are taken into account into module M4-8.
NOTE 2   Heat pumps generators for space heating using air (distribution) are taken into account in module M5-8.
Other generation systems such as boilers are covered in other sub modules of part M3-8.
This is the revision of EN 15316-4-2:2008. The revision covers the adaptation of the standard to hourly and monthly energy calculation.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15450:2007
Heating systems in buildings - Design of heat pump heating systems
EN 15450:2007

This standard specifies design criteria for heating systems in buildings using electrically driven heat pumps alone or in combination with other heat generators. Heat pump systems considered include (see Table 1):
-   water - water;
-   water - air;
-   brine - water;
-   refrigerant - water (direct expansion systems);
-   refrigerant - refrigerant;
-   air - air;
-   air - water.
This standard takes into account the heating requirements of attached systems (e.g. domestic hot water) in the design of heat supply, but does not cover the design of these systems. This standard covers only the aspects dealing with the heat pump, the interface with the heat distribution system and heat emission system (e.g. buffering system), the control of the whole system and the aspects dealing with energy source of the system.
Systems designed primarily for cooling and systems which can operate simultaneously in cooling and heating mode are not within the scope of this standard

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 15316-4-2:2022(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
prEN 15316-4-2

This document cover heat pumps for space heating, domestic hot water production and alternate operation, where the same heat pump delivers the heat to cover the space heating and domestic hot water heat requirement.
The document provides a calculation method under steady conditions that corresponds to one calculation interval.
This calculation is intended to be connected to the whole building calculation model and takes in account the external conditions and building controls that influence the energy requirements for heating supplied by the heat pump system.
The scope of this standard is to standardize the:
-   required inputs;
-   calculation methods;
-   required outputs;
of the generation for space heating and domestic hot water production of the following heat pump systems:
-   electrically-driven vapour compression cycle (VCC) heat pumps;
-   combustion engine-driven vapour compression cycle heat pumps;
-using combinations of heat source and heat sink listed in Table 1.
Table 1 - Heating sources and sinks
[table not represented]
This document does not cover sizing or inspection of heat pumps.
Heat pumps for cooling systems are taken into account in module M4–8. Other generation systems such as boilers are covered in other sub modules of part M3-8.
Table 2 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000 1.
NOTE 1   The same table can be found in CEN ISO/TR 52000 2, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
Table 2 - Position of this standard, within the modular structure of the set of EPB standards
[table not represented]

  • Draft
    141 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 15316-6-5:2018(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 6-5: Explanation and justification of EN 15316-4-2, Module M3-8
CEN/TR 15316-6-5:2017

This Technical Report (CEN/TR 15316-6-5) specifies details for EN 15316-4-2 and gives additional information for the application of EN 15316-4-2.

  • Technical report
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15316-4-2:2018(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
EN 15316-4-2:2017

The standard covers heat pumps for space heating, heat pump water heaters (HPWH) and heat pumps with combined space heating and domestic hot water production in alternate or simultaneous operation, where the same heat pump delivers the heat to cover the space heating and domestic hot water heat requirement.
The standard provides a calculation method under steady conditions that corresponds to one calculation step.
The results of this calculation are incorporated in larger building models and take in account the influence of the external conditions and building control that influence the energy requirements for heating supplied by the heat pump system.
The scope of this part is to standardise the:
-   required inputs;
-   calculation methods;
-   required outputs
for output thermal power generation for space heating and domestic hot water production of the following heat pump systems, including control:
-   electrically-driven vapour compression cycle (VCC) heat pumps;
-   combustion engine-driven vapour compression cycle heat pumps;
-   thermally-driven vapour absorption cycle (VAC) heat pumps,
using combinations of heat source and heat distribution listed in Table 1.
This standard does not cover sizing or inspection of heat pumps.
This standard deals with heat generators for heating or for combined domestic hot water and heating service. Generators for domestic hot water only are taken into account into module M8-8.
NOTE 1   Heat pumps generators for cooling systems are taken into account into module M4-8.
NOTE 2   Heat pumps generators for space heating using air (distribution) are taken into account in module M5-8.
Other generation systems such as boilers are covered in other sub modules of part M3-8.
This is the revision of EN 15316-4-2:2008. The revision covers the adaptation of the standard to hourly and monthly energy calculation.

  • Standard
    86 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    84 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    50 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 15450:2007
Heating systems in buildings - Design of heat pump heating systems
EN 15450:2007

This standard specifies design criteria for heating systems in buildings using electrically driven heat pumps alone or in combination with other heat generators. Heat pump systems considered include (see Table 1):
-   water - water;
-   water - air;
-   brine - water;
-   refrigerant - water (direct expansion systems);
-   refrigerant - refrigerant;
-   air - air;
-   air - water.
This standard takes into account the heating requirements of attached systems (e.g. domestic hot water) in the design of heat supply, but does not cover the design of these systems. This standard covers only the aspects dealing with the heat pump, the interface with the heat distribution system and heat emission system (e.g. buffering system), the control of the whole system and the aspects dealing with energy source of the system.
Systems designed primarily for cooling and systems which can operate simultaneously in cooling and heating mode are not within the scope of this standard

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
oSIST prEN 15316-4-2:2022(Main)
Energy performance of buildings - Method for calculation of system energy requirements and system efficiencies - Part 4-2: Space heating generation systems, heat pump systems, Module M3-8-2, M8-8-2
prEN 15316-4-2

This document cover heat pumps for space heating, domestic hot water production and alternate operation, where the same heat pump delivers the heat to cover the space heating and domestic hot water heat requirement.
The document provides a calculation method under steady conditions that corresponds to one calculation interval.
This calculation is intended to be connected to the whole building calculation model and takes in account the external conditions and building controls that influence the energy requirements for heating supplied by the heat pump system.
The scope of this standard is to standardize the:
-   required inputs;
-   calculation methods;
-   required outputs;
of the generation for space heating and domestic hot water production of the following heat pump systems:
-   electrically-driven vapour compression cycle (VCC) heat pumps;
-   combustion engine-driven vapour compression cycle heat pumps;
-using combinations of heat source and heat sink listed in Table 1.
Table 1 - Heating sources and sinks
[table not represented]
This document does not cover sizing or inspection of heat pumps.
Heat pumps for cooling systems are taken into account in module M4–8. Other generation systems such as boilers are covered in other sub modules of part M3-8.
Table 2 shows the relative position of this standard within the set of EPB standards in the context of the modular structure as set out in EN ISO 52000 1.
NOTE 1   The same table can be found in CEN ISO/TR 52000 2, with, for each module, the numbers of the relevant EPB standards and accompanying technical reports that are published or in preparation.
NOTE 2   The modules represent EPB standards, although one EPB standard may cover more than one module and one module may be covered by more than one EPB standard, for instance a simplified and a detailed method respectively. See also Clause 2 and Tables A.1 and B.1.
Table 2 - Position of this standard, within the modular structure of the set of EPB standards
[table not represented]

  • Draft
    141 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TP CEN/TR 12349:2023(Main)
Mechanical vibration - Guide to the health effects of vibration on the human body
CEN/TR 12349:2023

The aim of this CEN report is to provide information on the possible adverse health effects caused by exposure to vibration at work.  the report addresses manufacturers as well as employers and employees using vibrating machinery in order to improve their understanding of the possible health problems arising from occupational exposure to vibration.

  • Technical report
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 80004-1:2023(Main)
Nanotechnologies - Vocabulary - Part 1: Core vocabulary (ISO 80004-1:2023)
EN ISO 80004-1:2023

This document defines core terms in the field of nanotechnology. This document is intended to facilitate communication between organizations and individuals in industry and those who interact with them.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day