E12.13 - Photoluminescent Safety Markings

SIGNIFICANCE AND USE
4.1 To assess how photoluminescent markings perform under identical test conditions, the luminance shall be measured in accordance with this test method (see Specification E2072).
SCOPE
1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.  
1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
4.1 To assess how photoluminescent markings perform under identical test conditions, the luminance shall be measured in accordance with this test method (see Specification E2072).
SCOPE
1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.  
1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

SIGNIFICANCE AND USE
To assess how photoluminescent markings perform under identical test conditions, the luminance shall be measured in accordance with this test method (see Specification E 2072).
SCOPE
1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.
1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.
Formerly under the jurisdiction of Committee E12 on Color and Appearance, this test method was withdrawn in January 2019 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

ABSTRACT
This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and obstructions along the escape route. This specification does not cover potentially diminished performance due to wear and tear and aging. The photoluminescent safety materials shall be tested and shall conform to optical requirements and to the specified values of on-site luminance, activation, and marking width.
SCOPE
1.1 This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and obstructions along the escape route. (see also Test Method E2073 and Guide E2030).
1.2 This specification establishes minimum luminance values for photoluminescent (phosphorescent) markings.
1.3 This specification applies to all types of photoluminescent (phosphorescent) markings, including but not limited to plastics, coatings, ceramics, films, etc.
1.4 This specification does not cover potentially diminished performance due to wear and tear and aging.
1.5 This specification applies only to photoluminescent (phosphorescent) markings emitting the majority of spectral energy within the 515 to 535 nanometer range.
1.6 When reference is made regarding photoluminescence in the text of this standard, it implies phosphorescence.
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

SIGNIFICANCE AND USE
To assess how photoluminescent markings perform under identical test conditions, the luminance shall be measured in accordance with this test method (see Specification E 2072).
SCOPE
1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.
1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.
1.3 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and obstructions along the escape route. This specification does not cover potentially diminished performance due to wear and tear and aging. The photoluminescent safety materials shall be tested and shall conform to optical requirements and to the specified values of on-site luminance, activation, and marking width.
SCOPE
1.1 This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and obstructions along the escape route. (see also Test Method E 2073  and Guide E 2030).
1.2 This specification establishes minimum luminance values for photoluminescent (phosphorescent) markings.
1.3 This specification applies to all types of photoluminescent (phosphorescent) markings, including but not limited to plastics, coatings, ceramics, films, etc.
1.4 This specification does not cover potentially diminished performance due to wear and tear and aging.
1.5 This specification applies only to photoluminescent (phosphorescent) markings emitting the majority of spectral energy within the 515 to 535 nanometer range.
1.6 When reference is made regarding photoluminescence in the text of this standard, it implies phosphorescence.
1.7 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.

SIGNIFICANCE AND USE
Photoluminescent safety markings may be used to indicate the direction of the means of egress (escape route).
Note 1—Specification E 2072 covers photometric requirements for photoluminescent (phosphorescent) safety materials.
Photoluminescent safety markings can be divided into the following categories:
Floor Mounted Markings—These markings include floor tiles, stair treads, stair nosings, floor inserts, tactile warning strips, coatings, epoxy casting resins, and other markings attached to the floor.
Wall Mounted Markings—These markings include coatings, wall bases, tapes, corner guards, signage, exit maps, guidance strips, and other markings attached to walls, doors, handrails, columns, and other obstructions.
SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Photoluminescent safety markings may be used to indicate the direction of the means of egress (escape route).
Note 1—Specification E 2072 covers photometric requirements for photoluminescent (phosphorescent) safety materials.
Photoluminescent safety markings can be divided into the following categories:
Floor Mounted Markings—These markings include floor tiles, stair treads, stair nosings, floor inserts, tactile warning strips, coatings, epoxy casting resins, and other markings attached to the floor.
Wall Mounted Markings—These markings include coatings, wall bases, tapes, corner guards, signage, exit maps, guidance strips, and other markings attached to walls, doors, handrails, columns, and other obstructions.
SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
To assess how photoluminescent markings perform under identical test conditions, the luminance shall be measured in accordance with this test method (see Specification E 2072).
SCOPE
1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.
1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.
1.3 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Photoluminescent safety markings may be used to indicate the direction of the means of egress (escape route).  
Note 1—Specification E 2072 covers photometric requirements for photoluminescent (phosphorescent) safety materials.
Photoluminescent safety markings can be divided into the following categories:
4.2.1 Floor Mounted Markings—These markings include floor tiles, stair treads, stair nosings, floor inserts, tactile warning strips, coatings, epoxy casting resins, and other markings attached to the floor.
4.2.2 Wall Mounted Markings—These markings include coatings, wall bases, tapes, corner guards, signage, exit maps, guidance strips, and other markings attached to walls, doors, handrails, columns, and other obstructions.
SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and obstructions along the escape route. This specification does not cover potentially diminished performance due to wear and tear and aging. The photoluminescent safety materials shall be tested and shall conform to optical requirements and to the specified values of on-site luminance, activation, and marking width.
SCOPE
1.1 This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and other potentially dangerous objects. (see also Test Method E 2073, Test Method for Photopic Luminance of Photoluminescent (Phosphorescent) Markings, and Guide E 2030, Guide for Recommended Uses of Photoluminescent Safety Markings).
1.2 This specification establishes minimum luminance values for photoluminescent (phosphorescent) markings for detection in clear air under blackout conditions.
1.3 This specification applies to all types of photoluminescent (phosphorescent) markings, including but not limited to plastics, coatings, ceramics, films, etc.
1.4 This specification does not cover potentially diminished performance due to wear and tear and aging.
1.5 This specification applies only to photoluminescent (phosphorescent) markings emitting the majority of spectral energy within the 515 to 535 nanometer range.
1.6 When reference is made regarding photoluminescence in the text of this standard, it implies phosphorescence.
1.7 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.

SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
1.2 &si-value;
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.
1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.
1.3 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and other potentially dangerous objects. (see also Test Method E 2073, Test Method for Photopic Luminance of Photoluminescent (Phosphorescent) Markings, and Guide E 2030, Guide for Recommended Uses of Photoluminescent Safety Markings).
1.2 This specification establishes minimum luminance values for photoluminescent (phosphorescent) markings for detection in clear air under blackout conditions.
1.3 This specification applies to all types of photoluminescent (phosphorescent) markings, including but not limited to plastics, coatings, ceramics, films, etc.
1.4 This specification does not cover potentially diminished performance due to wear and tear and aging.
1.5 This specification applies only to photoluminescent (phosphorescent) markings emitting the majority of spectral energy within the 515 to 535 nanometer range.
1.6 When reference is made regarding photoluminescence in the text of this standard, it implies phosphorescence.
1.7 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.

SCOPE
1.1 This test method covers a procedure for determining the photopic luminance of photoluminescent (phosphorescent) markings. It does not cover scotopic or mesopic measurements.
1.2 When reference is made regarding photoluminescence in the text of this test method, it implies phosphorescence.
1.3 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and other potentially dangerous objects. (see also Test Method E 2073, Test Method for Photopic Luminance of Photoluminescent (Phosphorescent) Markings, and Guide E 2030, Guide for Recommended Uses of Photoluminescent Safety Markings).
1.2 This specification establishes minimum luminance values for photoluminescent (phosphorescent) markings for detection in clear air under blackout conditions.
1.3 This specification applies to all types of photoluminescent (phosphorescent) markings, including but not limited to plastics, coatings, ceramics, films, etc.
1.4 This specification does not cover potentially diminished performance due to wear and tear and aging.
1.5 This specification applies only to photoluminescent (phosphorescent) markings emitting the majority of spectral energy within the 515 to 535 nanometer range.
1.6 When reference is made regarding photoluminescence in the text of this standard, it implies phosphorescence.
1.7 The values stated in SI units are the standard. The values given in parentheses are provided for information purposes only.

SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings to supplement emergency lighting. This guide does not establish a standard practice to follow.
1.2 The values stated in SI units are the standard. The values given in parentheses are for information purposes only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings to supplement emergency lighting. This guide does not establish a standard practice to follow.
1.2 The values stated in SI units are the standard. The values given in parentheses are for information purposes only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

ABSTRACT
This specification covers minimum photometric requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and obstructions along the escape route. This specification does not cover potentially diminished performance due to wear and tear and aging. The photoluminescent safety materials shall be tested and shall conform to optical requirements and to the specified values of on-site luminance, activation, and marking width.
SCOPE
1.1 This specification covers minimum performance requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and obstructions along the escape route. (see also Test Method E2073 and Guide E2030).  
1.2 This specification establishes minimum luminance values for photoluminescent (phosphorescent) markings.  
1.3 This specification applies to all types of photoluminescent (phosphorescent) markings, including but not limited to plastics, coatings, ceramics, films, etc.  
1.4 This specification does not cover potentially diminished performance due to wear and tear and aging.  
1.5 This specification applies only to photoluminescent (phosphorescent) markings emitting the majority of spectral energy within the 515 to 535 nanometer range.  
1.6 When reference is made regarding photoluminescence in the text of this standard, it implies phosphorescence.  
1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
WITHDRAWN RATIONALE
This specification covered minimum performance requirements for newly applied photoluminescent (phosphorescent) safety materials used to provide supplemental markings of escape routes, emergency equipment, and obstructions along the escape route.
Formerly under the jurisdiction of Committee E12 on Color and Appearance, this specification was withdrawn in July 2023 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

SIGNIFICANCE AND USE
Photoluminescent safety markings may be used to indicate the direction of the means of egress (escape route).
Note 1—Specification E 2072 covers photometric requirements for photoluminescent (phosphorescent) safety materials.
Photoluminescent safety markings can be divided into the following categories:
Floor Mounted Markings—These markings include floor tiles, stair treads, stair nosings, floor inserts, tactile warning strips, coatings, epoxy casting resins, and other markings attached to the floor.
Wall Mounted Markings—These markings include coatings, wall bases, tapes, corner guards, signage, evacuation route diagrams, guidance strips, and other markings attached to walls, doors, handrails, columns, and other obstructions.
SCOPE
1.1 This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
This guide describes recommended uses and information on installation of photoluminescent safety markings. This guide does not establish a standard practice to follow. Required markings shall be installed in accordance with applicable building codes.
Formerly under the jurisdiction of Committee E12 on Color and Appearance, this guide was withdrawn in January 2018 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.