F15.33 - Outdoor Plastic Lawn Furniture

SIGNIFICANCE AND USE
Tests and criteria as outlined determine the overall usability and stability of chairs in an environment simulating the conditions of use.
Tests simulate two types of surfaces:
Smooth surfaces such as linoleum, wet pool decks, etc. The glass testing base (see Fig. 2) is used to simulate this surface.
Rough surfaces such as wooden decks, outdoor natural surfaces, etc. The plywood testing base (see Fig. 3) is used to simulate this surface.
Note 1—(A) Poly(methyl methacrylate) sheet, 0.25 ± 0.03-in. (6 ± 0.1-mm) thickness; (B) AC exterior glue fir plywood sheet, 0.75 ± 0.08 in. (19 ± 0.2 mm) or greater in thickness; (C) polypropylene microfoam sheet; 0.7 ± 0.01-lb/ft3  (11 ± 0.2-kg/m3) density and 0.13 ± 0.01-in. (3 ± 0.03-mm) thickness; and (D) glass/tempered sheet, 0.38 ± 0.04-in. (10 ± 0.1-mm) thickness.
Note 2—(A), (B), (C), and (D) shall be roughly the same dimensions, 48 in. (1219 mm) or greater. FIG. 2 Glass Testing Base
Note 1—(A) Poly(methyl methacrylate) sheet, 0.25 ± 0.03-in. (6 ± 0.1-mm) thickness; and (B) AC exterior glue fir plywood sheet, 0.75 ± 0.08 in. (19 ± 0.2 mm) or greater in thickness.
Note 2—(A) and (B) shall be roughly the same dimensions, 48 in. (1219 mm) or greater. FIG. 3 Plywood Testing Base
SCOPE
1.1 These standard performance requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) child's plastic chairs intended for outdoor use.
1.2 These standard performance requirements are not applicable to chaises, multi-positional chairs, upholstered chairs, or other types of furniture.
1.3 These standard performance requirements cover the performance of product regarding aspects of outdoor weathering, impact, static load, and rear leg testing.
1.4 Products Manufactured from Recycled Plastics:  
1.4.1 Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
WITHDRAWN RATIONALE
These standard performance requirements established nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) child's plastic chairs intended for outdoor use.
Formerly under the jurisdiction of Committee F15 on Consumer Products, these performance requirements were withdrawn in July 2017 in accordance with section 10.5.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

SIGNIFICANCE AND USE
Tests and criteria as outlined determine the overall usability and stability of chairs in an environment simulating the conditions of use.
Tests simulate two types of surfaces:
Smooth surfaces, such as linoleum, wet pool decks, etc. The glass testing base (see Fig. 5) is used to simulate this surface.
Rough surfaces, such as wooden decks, outdoor natural surfaces, etc. the plywood testing base (see Fig. 6) is used to simulate this surface.
Note 1—(A) Poly(methyl methacrylate) sheet, 0.25 ± 0.03-in. (6 ± 0.1-mm) thickness; (B) AC exterior glue fir plywood sheet, 0.75 ± 0.08 in. (19 ± 0.2 mm) or greater in thickness; (C) polypropylene microfoam sheet; 0.7 ± 0.01-lb/ft3 (11 ± 0.2-kg/m3) density and 0.13 ± 0.01-in. (3 ± 0.03-mm) thickness; and (D) glass/tempered sheet, 0.38 ± 0.04-in. (10 ± 0.1-mm) thickness.
Note 2—(A), (B), (C), and (D) shall be roughly the same dimensions, 48 in. (1219 mm) or greater. FIG. 5 Glass Testing Base
Note 1—(A) Poly(methoyl methoacrylate) sheet, 0.25 ± 0.03-in. (6 ± 0.1-mm) thickness; and (B) AC exterior glue fir plywood sheet, 0.75 ± 0.08 in. (19 ± 0.2 mm) or greater in thickness.
Note 2—(A) and (B) shall be roughly the same dimensions, 48 in. (1219 mm) or greater. FIG. 6 Plywood Testing Base
SCOPE
1.1 These performance requirements cover nationally recognized performance requirements for multipositional plastic chairs, with adjustable backs or reclining mechanisms, intended for outdoor use.
1.2 These performance requirements are not applicable to chaise lounges, upholstered chairs, or other types of furniture.
1.3 These performance requirements cover the performance of the product regarding aspects of outdoor weathering, impact, static load for seat and back, and arm testing.
1.4 Products Manufactured from Recycled Plastics—Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Tests and criteria as outlined determine the overall usability and stability of chairs in an environment simulating the conditions of use.
Tests simulate two types of surfaces:
Smooth surfaces such as linoleum, wet pool decks, etc. The glass testing base (see Fig. 5) is used to simulate this surface.
Rough surfaces such as wooden decks, outdoor natural surfaces, etc. The plywood testing base (see Fig. 6) is used to simulate this surface.
Note 1—
A = poly(methyl methacrylate) 0.25 ± 0.03 in. (6 ± 0.1 mm) thickness,
B = AC exterior glue fir plywood 0.75 ± 0.1 in. (19 ± 2 mm) or greater thickness,
C = polypropylene microfoam 0.7± 0.01 lb/ft3 (11 ± 0.2 kg/m3) density and 0.13 ± 0.01 in. (3 ± 0.03 mm) thickness, and
D = glass/tempered 0.38 ± 0.04 in. (10 ± 0.1 mm) thickness.
Note 2—A, B,C, and D are sheets roughly 48 in. (1219 mm) on a side or greater to accommodate the length of the chaise lounge. FIG. 5 Glass Testing Base
Note 1—
A = poly(methyl methacrylate) 0.25 ± 0.03 in. (6 ± 0.1 mm) thickness, and
B = AC exterior glue fir plywood 0.75 ± 0.1 in. (19 ± 2 mm) or greater thickness.
Note 2—A and B are sheets roughly 48 in. (1219 mm) on a side or greater to accommodate the length of the chaise lounge. FIG. 6 Plywood Testing Base
SCOPE
1.1 These performance requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chaise lounges, with or without moving arms, with adjustable backs, intended for outdoor use.
1.2 The performance requirements are not applicable to upholstered chairs, or other types of furniture.
1.3 These performance requirements cover the performance of the product regarding aspects of outdoor weathering, impact, static load for seat and back, and arm testing.
1.4 Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SIGNIFICANCE AND USE
Tests and criteria as outlined determine the overall usability and stability of chairs in an environment simulating the conditions of use.
Tests simulate two types of surfaces:
Smooth surfaces such as linoleum, wet pool decks, etc. The glass testing base (Fig. 2) is used to simulate this surface.
Rough surfaces such as wooden decks, outdoor grassed areas, etc. The plywood testing base (Fig. 3) is used to simulate this surface.
Note—A = poly(methyl methacrylate) sheet (see standard specifications); B = AC exterior glue fir plywood (see standard specifications); C = polypropylene microfoam sheet (see standard specifications); D = glass/tempered (see standard specifications). FIG. 2 Glass Testing Base
Note—A = poly(methyl methacrylate) sheet (see standard specifications); B = AC exterior glue fir plywood (see standard specifications). FIG. 3 Plywood Testing Base
SCOPE
1.1 These requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chairs intended for outdoor use.
1.2 These requirements do not address conditions that affect the performance of the chair beyond the manufacturing site.
1.3 These requirements are not applicable to chaises, multipositional chairs, upholstered chairs, or other types of furniture.
1.4 These requirements cover the physical performance of product regarding the aspects of outdoor weathering, impact, static load, and rear leg testing.
1.5 Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.6 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These standard performance requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) child's plastic chairs intended for outdoor use.
1.2 These standard performance requirements are not applicable to chaises, multi-positional chairs, upholstered chairs, or other types of furniture.
1.3 These standard performance requirements cover the performance of product regarding aspects of outdoor weathering, impact, static load, and rear leg testing.
1.4 Products Manufactured from Recycled Plastics:
1.4.1 Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These performance requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chaise lounges, with or without moving arms, with adjustable backs, intended for outdoor use.
1.2 The performance requirements are not applicable to upholstered chairs, or other types of furniture.
1.3 These performance requirements cover the performance of the product regarding aspects of outdoor weathering, impact, static load for seat and back, and arm testing.
1.4 Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These performance requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chaise lounges, with or without moving arms, with adjustable backs, intended for outdoor use.
1.2 The performance requirements are not applicable to upholstered chairs, or other types of furniture.
1.3 These performance requirements cover the performance of the product regarding aspects of outdoor weathering, impact, static load for seat and back, and arm testing.
1.4 Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These performance requirements cover nationally recognized performance requirements for multipositional plastic chairs, with adjustable backs or reclining mechanisms, intended for outdoor use.
1.2 These performance requirements are not applicable to chaise lounges, upholstered chairs, or other types of furniture.
1.3 These performance requirements cover the performance of the product regarding aspects of outdoor weathering, impact, static load for seat and back, and arm testing.
1.4 Products Manufactured from Recycled Plastics—Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.5 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chairs intended for outdoor use.
1.2 These requirements do not address conditions that affect the performance of the chair beyond the manufacturing site.
1.3 These requirements are not applicable to chaises, multipositional chairs, upholstered chairs, or other types of furniture.
1.4 These requirements cover the physical performance of product regarding the aspects of outdoor weathering, impact, static load, and rear leg testing.
1.5 Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These performance requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chaise lounges, with or without moving arms, with adjustable backs, intended for outdoor use.
1.2 The performance requirements are not applicable to upholstered chairs, or other types of furniture.
1.3 These performance requirements cover the performance of the product regarding aspects of outdoor weathering, impact, static load for seat and back, and arm testing.
1.4 Products may be manufactured from recycled plastics as long as the performance requirements are met.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These performance requirements cover nationally recognized performance requirements for multipositional plastic chairs, with adjustable backs or reclining mechanisms, intended for outdoor use.

SCOPE
1.1 These standard performance requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) child's plastic chairs intended for outdoor use.  
1.2 These standard performance requirements are not applicable to chaises, multipositional chairs, upholstered chairs, or other types of furniture.  
1.3 These standard performance requirements cover the performance of product regarding aspects of outdoor weathering, impact, static load, and rear leg testing.  
1.4 Products Manufactured from Recycle Plastics:  
1.4.1 Products may be manufactured from recycled plastics a long as the performance requirements are met.  
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in an parentheses are for information only.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

SCOPE
1.1 These requirements establish nationally recognized performance requirements for Class A (residential) and Class B (nonresidential) plastic chairs intended for outdoor use.
1.2 These requirements do not address conditions that affect the performance of the chair beyond the manufacturing site.
1.3 These requirements are not applicable to chaises, multipositional chairs, upholstered chairs, or other types of furniture.
1.4 These requirements cover the physical performance of product regarding the aspects of impact, static load, and rear leg testing.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.