CLC/TC 17B - Low-voltage switchgear and controlgear including dimensional standardization

This International Standard applies to controllers intended for starting, controlling and stopping stationary fire pumps, including automatic and non-automatic types for alternating current electric motor or diesel engine-driven fire pumps. It is anticipated that a controller only controls a single driver. This first edition cancels and replaces the technical specification published in 2003. It constitutes a technical revision and now has the status of an International Standard.

Superseded by EN 60947-4-2:2012

Superseded by EN 60947-4-1:2010

Superseded by EN 60947-3:2009

Applies, when required by the relevant product standard, to switchgear and controlgear hereinafter referred to as equipment and intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c. It does not apply to low-voltage switchgear and controlgear assemblies which are dealt with in EN 60439. The object of this standard is to state those general rules and requirements which are common to low-voltage equipment as defined in 1.1, including for example: - definitions; - characteristics; - information supplied with the equipment; - normal service, mounting and transport conditions; - constructional and performance requirements; - verification of characteristics and performance

Superseded by EN 60947-5-2:2007

This standard applies to flat connections of low-voltage switchgear and controlgear by means of flat terminals with one clearance hole, or one threated hole, or one screw or stud, which are designed for the connection of rectangular bars or of lugs for round conductors. The extension of this standard to terminals with 2, 3 or 4 clearance or threated holes, screws or studs is under consideration.

This standard applies to contactors according to IEC-Standard 158-1, irrespective of their power and construction, having terminal marking of auxiliary contacts in accordance with the corresponding marking of contactor relays designated by the distinctive letter E (see EN 50 011). The use of this standard is recommended where terminal marking is a requirement of the relevant standard for contactor auxiliary contacts, or is usual practice

Applies to circuit-breakers, the main contacts of which are intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c.; it also contains additional requirements for integrally fused circuit-breakers. It applies whatever the rated currents, the method of construction or the proposed applications of the circuit-breakers may be.

EN following parallel vote * Superseded by EN 60947-4-1:2010

EN following parallel vote * Superseded by EN 60947-7-3:2009

EN following parallel vote * Superseded by EN 60947-7-1:2009

Applies to protective conductor terminal blocks with PE function up to 120 mm2 (250 MCM) and to protective conductor terminal blocks with PEN function equal to and above 10 mm2 (AWG 8).

This standard applies to motor contactors having the following characteristics: rated voltage 380 (415) V three phase alternating current of 50 Hz frequency; a life of one million electrical operations at a rate which can be, for example, 120 operations per hour for category AC3 to IEC publication 158-1 (1970); a power not exceeding 11 kW

The present standard is applicable generally to low voltage apparatus such as for example contractors, switches, isolators, circuit breakers, starters, auxiliary control devices, electrical relays which are currently used in assemblies of switch gear and control gear, electrical equipment of machines and industrial installations. The purpose of the present standard is to establish the dimensions, including the fixing dimensions, of low voltage industrial apparatus

The present standard applies to contactor relays and primarily to those having from 4 to 10 contacts, of which the rated working voltage does not exceed 380V (415V) alternating current, and the terminals of which each permit the connection of either one or two flexible conductors of 1.5 mm2 maximum cross section or of a single flexible conductor of 2.5 mm2 maximum cross section It is recommended that these indicated dimensions should also be used for auxiliary contactors having characteristics which differ from those given above

EN following parallel vote * Superseded by EN 60947-4-2:2012

EN following parallel vote * Superseded by EN 60947-1:2004

EN following parallel vote * Superseded by EN 60947-2:2003

EN following parallel vote * Superseded by EN 60947-3:2009

States the characteristics of contactors and starters and associated equipment, the conditions with which contactors or starters shall comply (operation and behaviour, dielectric properties, the degrees of protection provided by their enclosures, their construction), the tests intended for confirming that these conditions have been met, the information to be given with the equipment or in the manufacturer's literature. This publication supersedes EN 60158-1 (1970) and its Amendment 1 (1983), 60158-1C (1982), 60292-1 (1969) and its Amendment 2 (1983), 60292-2 (1970), 60292-3 (1973) and 60292-4 (1975). It should be read in conjunction with EN 60947-1.

EN following parallel vote * Superseded by EN 60947-1:2004

Aapplies to controllers and starters, which may include a series mechanical switching device, intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V a.c.

EN following parallel vote * Superseded by EN 60947-5-1:2004

Includes and replaces A11:1997 * Superseded by EN 60947-5-1:2004

This European Standard states the requirements for proximity devices with analogue output. They may consist of one or more parts. The requirements of EN 60947-5-2 modified according to this standard apply. The clause numbering in this standard follows the clause numbering of EN 60947-5-2

EN following parallel vote * Supersedes A11:1997 * Superseded by EN 60947-7-1:2002

EN following parallel vote * Superseded by EN 60947-5-2:2007

EN following parallel vote * Superseded by EN 60947-5-1:2004

States the characteristics of the equipment, the conditions with which the equipment shall comply (operation and behaviour in normal service, operation and behaviour in case of specified abnormal conditions, dielectric properties) the test for confirming that these conditions have been met and the methods to be adopted for these tests; the information to be marked on the equipment or made available by the manufacturer, e.g. in the catalogue.

Applies, when required by the relevant product standard, to switchgear and controlgear hereinafter referred to as "equipment" and intended to be connected to circuits, the rated voltage of which does not exceed 1 000 V a.c. or 1 500 V d.c. It states those general rules and requirements which are common to low-voltage equipment as defined in Subclause 1.1, including for example: definitions, characteristics, information supplied with the equipment, normal service, mounting and transport conditions, constructional and performance requirements, verification of characteristics and performance.

EN following parallel vote * Superseded by EN 60947-6-2:2003

EN following parallel vote * Superseded by EN 60947-4-2:2000

EN following parallel vote * Superseded by EN 60947-1:1999

EN following parallel vote * Corrigendum to A1 issued April 2001 * Superseded by EN 61095:2009

This European Standard specifies requirements for one size of top hat steel rails for the fixing of terminal blocks

This European Standard specifies requirements for certain sizes of C-profile steel rail and accessories for the screw fixing of equipment

This European Standard specifies requirements for one size of G-profile steel rail for the fixing of terminal blocks

D105/023: EN withdrawn

This standard specifies 35 mm wide steel top hat rails for the snap-on mounting of equipment

D100/022: EN withdrawn

D100/022: EN withdrawn

D100/022: EN withdrawn

D100/022: EN withdrawn

D100/022: EN withdrawn

D100/022: EN withdrawn

D100/022: EN withdrawn

D100/022: EN withdrawn

D100/022: EN withdrawn

This standard applies to inductive and capacitive proximity switches that sense the presence of metallic and/or non-metallic objects, ultrasonic proximity switches that sense the presence of sound reflecting objects and photoelectric proximity switches that sense the presence of objects. These proximity switches are self-contained, have semiconductor switching elements(s) and are intended to be connected to circuits, the rated voltage of which does not exceed 250 V 50 Hz/60 Hz a.c. or 300 V d.c. This Standard is not intended to cover proximity switches with analogue outputs. The object of this standard is to state for proximity switches: Definitions; Classification; Characteristics; Product information; Normal service; mounting and transport conditions; Constructional and performance requirements; Tests to verify rated characteristics.