23.040.03 - Pipeline and its parts for external water conveyance systems

TC- request to correct clause 4 and equations in clause 7 - GA

This document specifies a test method for determining the long-term compression strength for a specified period on structural boxes made of thermoplastics materials for non-pressure underground conveyance and storage of non-potable water.
The document is applicable for boxes which maintain their linear behaviour over the specified period.

This document gives the definitions and specifies the minimum requirements for injection moulded, extruded and thermoformed thermoplastics cuboid shaped boxes, including integral components, used in underground systems for infiltration, attenuation and storage of non-potable water (e.g. storm water) and manufactured from unplasticized poly(vinyl chloride) (PVC-U) or polypropylene (PP).
NOTE 1   Specifications and design rules for systems (water reservoir) are described in part 2 of EN 17152.
Pro...view more

This European Standard specifies a method for determining short term compression strength on boxes made of thermoplastics materials for non-pressure underground conveyance and storage of non-potable water.

This European Standard specifies the requirements for industrial piping systems and supports, including safety systems, made of metallic materials with a view to ensure safe operation. This European Standard is applicable to metallic piping above  ground, ducted or buried, irrespective of pressure.
Introduction of a new Clause 7 "Accessories"

This document, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit
lining systems intended to be used for the renovation of water supply networks, which transport water
intended for human consumption, including raw water intake pipelines.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable
to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is
reduc...view more

This document specifies the requirements and test methods for plastics piping systems intended to be
used for the renovation of underground water supply networks. It is applicable to pipes and fittings, as
manufactured, as well as to the installed lining system. It is not applicable to the existing pipeline or
any non-structural sprayed coatings or annular filler.
This document gives the general requirements common to all relevant renovation techniques.

This International Standard, read in conjunction with Part 1, specifies requirements and test methods for pipes and fittings which are part of plastics piping systems installed as continuous pipes in the renovation of underground water supply networks. It is applicable to PE pipes of three different types:
-   PE solid wall single layered pipes (nominal outside diameter, dn ), including any identification stripes;
-   PE pipes with co-extruded layers on either or both the outside and inside of the p...view more

This European Standard specifies the requirements for industrial piping systems and supports, including safety systems, made of metallic materials with a view to ensure safe operation.
This European Standard is applicable to metallic piping above ground, ducted or buried, irrespective of pressure.
This European Standard is not applicable to:
-   Pipelines and their accessories;
-   Stream waterways such as penstocks, pressure tunnels, pressure shaft for hydro-electric-installations and their rel...view more

This part of EN 12200 gives guidance for the assessment of conformity of formulations, products, joints and assemblies in accordance with EN 12200 1:2016 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 12200 1:2016, this document is applicable to piping systems made of unplasticiz...view more

This standard specifies the requirements for pipes, fittings, brackets and the system of unplasticized poly(vinyl chloride) (PVC-U) intended for use as above-ground external rainwater downpipes.
It also specifies the requirements for metallic brackets.
It specifies both solid wall pipes and fittings, (i.e. product manufactured from a single layer), as well as solid wall multi-layer pipes.
Pipes can be used in conjunction with fittings and brackets of acrylic materials provided these polymers ...view more

This Technical Report is applicable to the installation of thermoplastics piping systems to be used for the conveyance of water or sewage under gravity and pressure conditions underground. It is intended to be used for pipes of nominal size up to and including DN 1600. Wherever the term “pipe” is used in this Technical Report, it also serves to cover any “fittings”, “ancillary” products and “components” if not otherwise specified.
NOTE 1 This document does not apply to pipelines for gas supply ...view more

This European Standard specifies the required properties of the piping system and its components made from glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) intended to be used for water supply (drinking or raw) with or without pressure. In a pipework system, pipes and fittings of different nominal pressure and stiffness ratings may be used together.
It is the responsibility of the purchaser or specifier to make the appropriate selections taking into accoun...view more

This European Standard specifies the requirements and associated test methods applicable to ductile iron fittings, ductile iron and mild steel couplings and flange adaptors and their joints to be used with poly(vinyl chloride) (PVC-U) pipes or polyethylene (PE) pipes. It is in conformity with EN 1452-1 to -5, ENV 1452-6 and -7 and EN 12201-1 to -5 respectively, for the construction of pipelines:
-   to convey water (e.g. water intended for human consumption);
-   with or without pressure;
-   to be...view more

This European Standard specifies the requirements and associated test methods applicable to ductile iron pipes, fittings, accessories and their joints for the construction of pipelines outside buildings:
-   to convey different types of water (e.g. raw water, treated water, re-used water) for all types of applications (e.g. water intended for human consumption, for fire protection, for snow making, for irrigation, for hydro-electricity etc.);
-   with or without pressure;
-   to be installed below ...view more

This standard specifies a method for testing the strength of fixing brackets intended to support plastics rainwater downpipe systems used externally on buildings. It is applicable to both metal and plastics brackets, and determines the amount of residual deformation after removal of a specified test load.

This International Standard, in conjunction with ISO 11298-1, specifies requirements and test methods for cured-in-place pipes and fittings used for the renovation of underground water supply networks. It applies to the use of various thermosetting resin systems, in combination with compatible fibrous carrier materials and other process-related plastics components.

This European Standard specifies requirements for plastics pipes and fittings for pressure applications for water supply, drainage, sewerage and irrigation, as well as for any other pressure application in which other liquids are conveyed with the exception of water intended for human consumption.
It is intended to be used for buried or above-ground conveyance of water, raw water prior to treatment, waste water, water for general purposes, vacuum-operated soil and waste conveyance and other li...view more

This European Standard specifies product characteristics for plastics pipes and fittings for pressure applications for water supply, drainage, sewerage and irrigation with the exception of water intended for human consumption.
Pipes and fittings covered by this standard are intended to be used for buried or above-ground conveyance of water, waste water, water for general purposes, vacuum-operated soil and waste conveyance, for both outside and inside buildings.
It gives the associated test/as...view more