SIST EN ISO 11298-3:2018
(Main)Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2018)
Plastics piping systems for renovation of underground water supply networks - Part 3: Lining with close-fit pipes (ISO 11298-3:2018)
This document, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit
lining systems intended to be used for the renovation of water supply networks, which transport water
intended for human consumption, including raw water intake pipelines.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable
to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is
reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner,
as well as associated fittings and joints for the construction of the lining system. It is not applicable to
PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe.
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of
20 °C as the reference temperature.
NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see
ISO 4427-1:2007, Annex A.
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Wasserversorgungsnetzen - Teil 3: Close-Fit-Lining (ISO 11298-3:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux enterrés d'alimentation en eau - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO 11298-3:2018)
Le présent document, conjointement à l'ISO 11298‑1, spécifie les exigences et les méthodes d'essai pour les systèmes de tubage par tuyau continu sans espace annulaire utilisés pour la rénovation des réseaux d'alimentation en eau, qui transportent de l'eau destiné à la consommation humaine, y compris les canalisations pour la prise d'eau brute.
Il s'applique aux tuyaux et raccords, tels que fabriqués, ainsi qu'au système de rénovation installé. Il s'applique aux tuyaux en polyéthylène (PE) ayant soit une construction monocouche à paroi compacte soit une construction à couches coextrudées, laquelle est réduite en usine ou sur site pour fournir un tubage autostructurant et un tubage nécessitant le maintien de l'enveloppe sans espace annulaire, ainsi qu'aux raccords associés et aux assemblages pour la construction du système de rénovation. Il ne s'applique pas aux tuyaux revêtus de PE comportant une couche thermoplastique supplémentaire pelable et contiguë à l'extérieur du tuyau.
Il s'applique aux tuyaux, raccords et montages en PE destinés à être utilisés à une température de fonctionnement de 20 °C, qui est la température de référence.
NOTE Pour les applications à des températures constantes comprises entre 20 °C et 40 °C, voir l'ISO 4427‑1:2007, Annexe A.
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z vodo - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11298-3:2018)
Ta dokument v povezavi s standardom ISO 11298-1 določa zahteve in preskusne metode za tesno prilagodljive sisteme cevi, ki se uporabljajo za obnovo podzemnih omrežij za oskrbo z vodo, po katerih se pretaka pitna voda, vključno s cevmi za dovajanje neobdelane vode.
Uporablja se za cevi in fitinge, kot so izdelani, ter za nameščene sisteme cevi. Uporablja se za polietilenske (PE) cevi s trdno steno iz ene plasti ali s konstrukcijo koekstrudiranih slojev, ki se v tovarni ali na mestu uporabe zmanjša, da se zagotovi tesno prilegajoča se neodvisna ali interaktivna obloga cevi pod tlakom, ter tudi za povezane fitinge in spoje za konstrukcijo sistema cevi. Ne uporablja se za cevi, prevlečene s polietilenom, ki imajo na zunanji strani stični, termoplastični dodatni sloj, ki ga je mogoče odluščiti. Uporablja se za polietilenske cevi, fitinge in sestave, namenjene za uporabo pri delovni temperaturi 20 °C kot referenčni temperaturi. OPOMBA: V zvezi z napravami, ki delujejo pri stalnih temperaturah od 20 do 40 °C, glej dodatek A k standardu ISO 4427-1:2007.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 11298-3:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 11298-3:2011
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za oskrbo z
vodo - 3. del: Oblaganje s tesno prilagodljivimi cevmi (ISO 11298-3:2018)
Plastics piping systems for renovation of underground water supply networks - Part 3:
Lining with close-fit pipes (ISO 11298-3:2018)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Wasserversorgungsnetzen - Teil 3: Close-Fit-Lining (ISO 11298-3:2018)
Systèmes de canalisations en plastique pour la rénovation des réseaux enterrés
d'alimentation en eau - Partie 3: Tubage par tuyau continu sans espace annulaire (ISO
11298-3:2018)
Ta slovenski standard je istoveten z: EN ISO 11298-3:2018
ICS:
23.040.03 Cevovodi za zunanje sisteme Pipeline and its parts for
transporta vode in njihovi deli external water conveyance
systems
93.025 Zunanji sistemi za prevajanje External water conveyance
vode systems
SIST EN ISO 11298-3:2018 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 11298-3:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 11298-3:2018
EN ISO 11298-3
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2018
EUROPÄISCHE NORM
ICS 23.040.20; 23.040.45; 93.025 Supersedes EN ISO 11298-3:2011
English Version
Plastics piping systems for renovation of underground
water supply networks - Part 3: Lining with close-fit pipes
(ISO 11298-3:2018)
Systèmes de canalisations en plastique pour la Kunststoff-Rohrleitungssysteme für die Renovierung
rénovation des réseaux enterrés d'alimentation en eau von erdverlegten Wasserversorgungsnetzen - Teil 3:
- Partie 3: Tubage par tuyau continu sans espace Close-Fit-Lining (ISO 11298-3:2018)
annulaire (ISO 11298-3:2018)
This European Standard was approved by CEN on 19 August 2018.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11298-3:2018 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 11298-3:2018
EN ISO 11298-3:2018 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 11298-3:2018
EN ISO 11298-3:2018 (E)
European foreword
This document (EN ISO 11298-3:2018) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be
withdrawn at the latest by April 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 11298-3:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 11298-3:2018 has been approved by CEN as EN ISO 11298-3:2018 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 11298-3:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 11298-3:2018
INTERNATIONAL ISO
STANDARD 11298-3
Second edition
2018-09
Plastics piping systems for renovation
of underground water supply
networks —
Part 3:
Lining with close-fit pipes
Systèmes de canalisations en plastique pour la rénovation des réseaux
enterrés d'alimentation en eau —
Partie 3: Tubage par tuyau continu sans espace annulaire
Reference number
ISO 11298-3:2018(E)
©
ISO 2018
---------------------- Page: 7 ----------------------
SIST EN ISO 11298-3:2018
ISO 11298-3:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 11298-3:2018
ISO 11298-3:2018(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 General . 2
3.2 Techniques . 2
3.3 Characteristics . 3
3.4 Materials . 3
3.5 Product stages . 3
3.6 Service conditions . 3
3.7 Joints . 4
4 Symbols and abbreviated terms . 4
4.1 Symbols . 4
4.2 Abbreviated terms . 5
5 Pipes at the “M” stage . 5
5.1 Materials . 5
5.1.1 Virgin material . 5
5.1.2 Reprocessable and recyclable material . 5
5.2 General characteristics . 5
5.2.1 Appearance . 5
5.2.2 Colour . 5
5.3 Material characteristics . 6
5.4 Geometric characteristics . 6
5.5 Mechanical characteristics. 6
5.6 Physical characteristics . 6
5.7 Jointing . 6
5.8 Marking . 6
5.9 Regional requirements for pipes . 7
6 Fittings at the “M” stage . 7
6.1 Requirements . 7
6.2 Marking . 7
6.3 Regional requirements for fittings . 7
7 Ancillary components . 7
8 Fitness for purpose of the installed lining system at the “I” stage .7
8.1 Materials . 7
8.2 General characteristics . 7
8.3 Material characteristics . 7
8.4 Geometric characteristics . 8
8.5 Mechanical characteristics. 8
8.6 Physical characteristics . 9
8.7 Additional characteristics . 9
8.8 Sampling . 9
8.9 Regional requirements for the installed lining system . 9
9 Installation practice . 9
9.1 Preparatory work . 9
9.2 Storage, handling and transport of pipes and fittings .10
9.3 Equipment .10
9.3.1 Butt fusion and debeading equipment .10
9.3.2 Reduction equipment .10
9.3.3 Pipe skids/rollers .11
© ISO 2018 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 11298-3:2018
ISO 11298-3:2018(E)
9.3.4 Winching and rod-pulling equipment .11
9.3.5 Pipe entry guides .11
9.3.6 Reforming equipment .11
9.3.7 Electrofusion equipment .11
9.3.8 Inspection equipment .11
9.3.9 Lifting equipment .12
9.4 Installation .12
9.5 Process-related inspection and testing .12
9.6 Lining termination .13
9.7 Reconnection to the existing pipeline system .13
9.8 Final inspection and testing .13
9.9 Documentation .13
Annex A (normative) Factory-folded heat-reverted polyethylene (PE) pipe —
Determination of memory ability .14
Bibliography .16
iv © ISO 2018 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 11298-3:2018
ISO 11298-3:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves for
the transport of fluids, SC 8, Rehabilitation of pipeline systems.
This second edition cancels and replaces the first edition (ISO 11298-3:2010), which has been
technically revised.
The main changes compared to the previous edition are as follows:
— Figure 1 and Clauses 1, 3.4, 3.6, 5.8, 8.4, 8.5 and 9.3 to 9.8 have been technically revised.
— New sub-clauses 5.9, 6.3 and 8.9 specifying regional requirements for pipes, fittings and the installed
lining system respectively, have also been added in accordance with the Vienna Agreement, to allow
reference to European standards in countries where these are mandated by law in place of ISO
standards of identical scope.
A list of all parts in the ISO 11298 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
© ISO 2018 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 11298-3:2018
ISO 11298-3:2018(E)
Introduction
This document is a part of a System Standard for plastics piping systems of various materials used for
the renovation of existing pipelines in a specified application area. System Standards for renovation
deal with the following applications:
— ISO 11296, Plastics piping systems for renovation of underground non-pressure drainage and sewerage
networks;
— ISO 11297, Plastics piping systems for renovation of underground drainage and sewerage networks
under pressure;
— ISO 11298, Plastics piping systems for renovation of underground water supply networks (this
document);
— ISO 11299, Plastics piping systems for renovation of underground gas supply networks.
These System Standards are distinguished from those for conventionally installed plastics piping
systems by the requirement to verify certain characteristics in the “as-installed” condition, after site
processing. This is in addition to specifying requirements for plastics piping systems components “as
manufactured”.
Each of the System Standards comprises a:
— Part 1: General
and all applicable renovation technique family-related parts, which for water supply networks include
or potentially include the following:
— Part 2: Lining with continuous pipes
— Part 3: Lining with close-fit pipes (this document)
— Part 4: Lining with cured-in-place pipes
— Part 5: Lining with discrete pipes
— Part 6: Lining with adhesive-backed hoses
— Part 10: Lining with sprayed polymeric materials
— Part 11: Lining with inserted hoses
The requirements for any given renovation technique family are specified in Part 1, applied in
conjunction with the relevant other part. For example, ISO 11298-1 and this document together specify
the requirements relating to lining with close-fit pipes. For complementary information, see ISO 11295.
Not all technique families are pertinent to every area of application and this is reflected in the part
numbers included in each System Standard.
A consistent structure of clause headings has been adopted for all parts of ISO 11298, in order to
facilitate direct comparisons across renovation technique families.
Figure 1 shows the common part and clause structure and the relationship between ISO 11298 and the
System Standards for other application areas.
vi © ISO 2018 – All rights reserved
---------------------- Page: 12 ----------------------
SIST EN ISO 11298-3:2018
ISO 11298-3:2018(E)
Figure 1 — Format of the renovation system standards
© ISO 2018 – All rights reserved vii
---------------------- Page: 13 ----------------------
SIST EN ISO 11298-3:2018
---------------------- Page: 14 ----------------------
SIST EN ISO 11298-3:2018
INTERNATIONAL STANDARD ISO 11298-3:2018(E)
Plastics piping systems for renovation of underground
water supply networks —
Part 3:
Lining with close-fit pipes
1 Scope
This document, in conjunction with ISO 11298-1, specifies requirements and test methods for close-fit
lining systems intended to be used for the renovation of water supply networks, which transport water
intended for human consumption, including raw water intake pipelines.
It applies to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable
to polyethylene (PE) pipes of either solid wall single layer or co-extruded layer construction, which is
reduced in the factory or on site to provide a close-fitting independent or interactive pressure pipe liner,
as well as associated fittings and joints for the construction of the lining system. It is not applicable to
PE coated pipes having a peelable, contiguous, thermoplastic additional layer on the outside of the pipe.
It is applicable to PE pipes, fittings and assemblies intended to be used at an operating temperature of
20 °C as the reference temperature.
NOTE For applications operating at constant temperatures greater than 20 °C and up to 40 °C, see
ISO 4427-1:2007, Annex A.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
ISO 4427-1:2007, Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply —
Part 1: General
ISO 4427-2:2007, Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply —
Part 2: Pipes
ISO 4427-3, Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 3:
Fittings
ISO 4427-5:2007, Plastics piping systems — Polyethylene (PE) pipes and fittings for water supply — Part 5:
Fitness for purpose of the system
ISO 11298-1:2018, Plastics piping systems for renovation of underground water supply networks —
Part 1: General
ISO 12176-1, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 1:
Butt fusion
ISO 12176-2, Plastics pipes and fittings — Equipment for fusion jointing polyethylene systems — Part 2:
Electrofusion
© ISO 2018 – All rights reserved 1
---------------------- Page: 15 ----------------------
SIST EN ISO 11298-3:2018
ISO 11298-3:2018(E)
EN 12201-1, Plastics piping systems for water supply, and for drainage and sewerage under pressure —
Polyethylene (PE) — Part 1: General
EN 12201-2:2011, Plastics piping systems for water supply, and for drainage and sewerage under
pressure — Polyethylene (PE) — Part 2: Pipes
EN 12201-3, Plastics piping systems for water supply, and for drainage and sewerage under pressure —
Polyethylene (PE) — Part 3: Fittings
EN 12201-4, Plastics piping systems for water supply — Polyethylene (PE) — Part 4: Valves
EN 12201-5, Plastics piping systems for water supply, and for drainage and sewerage under pressure —
Polyethylene (PE) — Part 5: Fitness for purpose of the system
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 11298-1:2018 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— IEC Electropedia: available at http: //www .electropedia .org/
— ISO Online browsing platform: available at https: //www .iso .org/obp
3.1 General
3.1.1
compound formulation
clearly defined homogenous mixture of base polymer with additives, e.g. antioxidants, pigments,
stabilizers and others, at a dosage level necessary for the processing and intended use of the final product
3.1.2
solid wall single layered pipe
pipe with smooth internal and external surface, extruded from the same compound formulation (3.1.1)
throughout the wall
3.1.3
pipe with co-extruded layers
pipe with smooth internal and external surface, having co-extruded layers on either or both the outside
and inside of the pipe, where all layers have the same MRS rating
3.1.4
close fit
situation of the outside of the installed liner relative to the inside of th
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.