29.035.01 - Insulating materials in general

IEC 60112:2020 specifies the method of test for the determination of the proof and comparative tracking indices of solid insulating materials on pieces taken from parts of equipment and on plaques of material using alternating voltage. This document provides a procedure for the determination of erosion when required. This test method evaluates the composition of the material as well as the surface of the material being evaluated. Both the composition and surface condition directly influence the ...view more

IEC TS 62836:2020(E) provides an efficient and reliable procedure to test the internal electric field in the insulating materials used for high-voltage applications, using the pressure wave propagation (PWP) method. It is suitable for a sample with homogeneous insulating materials and an electric field higher than 1 kV/mm, but it is also dependent on the thickness of the sample and the pressure wave generator.

IEC 60112:2020 specifies the method of test for the determination of the proof and comparative tracking indices of solid insulating materials on pieces taken from parts of equipment and on plaques of material using alternating voltage. This document provides a procedure for the determination of erosion when required.
This test method evaluates the composition of the material as well as the surface of the material being evaluated. Both the composition and surface condition directly influence t...view more

IEC TR 61244-4:2019(E) provides general guidance for the evaluation/verification of electrical insulation materials (EIM) and electrical insulation systems (EIS) intended to be used in types of equipment exposed to ionizing radiation. Beside sensors, actuators/motors as well as plugs and terminals, cables are a well-known typical application of those EIM and EIS. Their type spectrum covers low voltage power cables, control cables and instrumentation cables. Because of their comparable simple des...view more

This part of IEC 62677 is applicable to heat shrinkable low and medium voltage moulded shapes, conductive, in a range of configurations suitable for environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between −40 ºC and 100 ºC.
The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in An...view more

IEC 62899-502-2:2019(E) specifies the combined mechanical and environmental stress test methods for flexible OLED (organic light emitting diode) elements fabricated using the printing method. Mechanical stress tests include the static and cycling vending test, and the dynamic and static rolling test.

IEC 62677-3-103:2019 is applicable to heat shrinkable low and medium voltage moulded shapes, conductive, in a range of configurations suitable for environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between -40 ºC and 100 ºC. The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in Annex ...view more

This part of IEC 62631 covers procedures for the determination of insulation resistance and
volume resistivity of insulating materials by applying DC-voltage and temperatures up to
800 °C. The typical application materials include high temperature mica plate and alumina
ceramics.

IEC 62677-3-103:2019 is applicable to heat shrinkable low and medium voltage moulded shapes, conductive, in a range of configurations suitable for environmental sealing, mechanical protection, strain relief for power cable terminations, joints and stop ends. These moulded shapes have been found suitable for use for temperatures between -40 ºC and 100 ºC. The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive compatibility and temperature performance is given in Annex ...view more

This part of IEC 62631 covers procedures for the determination of insulation resistance and volume resistivity of insulating materials by applying DC-voltage and temperatures up to 800 °C. The typical application materials include high temperature mica plate and alumina ceramics.

IEC 62631-3-4:2019 covers procedures for the determination of insulation resistance and volume resistivity of insulating materials by applying DC-voltage and temperatures up to 800 °C. The typical application materials include high temperature mica plate and alumina ceramics.
This edition of IEC 62631-3-4 cancels and replaces IEC 60345 “Method of test for electrical resistance and resistivity of insulating materials at elevated temperatures”, published in 1971. This edition constitutes a techni...view more

This part of IEC 62677 is applicable to heat shrinkable low voltage moulded shapes in a range
of configurations suitable for insulation, environmental sealing, mechanical protection, strain
relief for power cable terminations, joints and stop ends. These moulded shapes have been
found suitable for use for temperatures between –40 °C and 100 °C.
The moulded shapes can be supplied with a pre-coated adhesive. A guide to adhesive
compatibility and temperature performance is given in Annex A. Th...view more

This part of IEC 62631 describes test methods for the determination of permittivity and
dissipation factor properties of solid insulating materials (AC methods from 0,1 Hz up to
10 MHz).
NOTE This part of the standard mainly considers measuring setups with guard-electrodes.

IEC 61375-2-6:2018 establishes the specification for the communication between the on-board subsystems and the ground subsystems. The communication system, interfaces and protocols are specified as a mobile communication function, using any available wireless technology. This document provides requirements in order to:
a) select the wireless network on the basis of QoS parameters requested by the application;
b) allow TCMS and/or OMTS applications, installed on-board and communicating on the o...view more

IEC 60375:2018 specifies the rules for signs and reference directions and reference polarities for electric currents and voltages in electric networks.