43.080.01 - Commercial vehicles in general

This document provides a set of codes for the exchange of dimensional data between truck chassis manufacturers and bodywork manufacturers. The process of exchanging the above information can involve: — chassis manufacturer; — chassis importer; — chassis dealer; — one or more bodywork manufacturers; and — bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loading equipment, tipping equipment.

This document provides codes for the exchange of general, mass and administrative information between truck chassis manufacturers and bodywork manufacturers. The process of exchanging the above information can involve: — chassis manufacturer; — chassis importer; — chassis dealer; — one or more bodywork manufacturers; — bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loading equipment, tipping equipment.

This document specifies the minimum requirements and test methods for lashing points for cargo securing on commercial vehicles and intermodal loading units for cargo transport.
This document does not apply to:
-   Vehicles and intermodal loading units manufactured before publication of this standard;
-   Vehicles and intermodal loading units designed and constructed exclusively for the transport of bulk materials;
-   Vehicles and intermodal loading units designed and constructed exclusively for t...view more

This document specifies a method for comparing simulation results from a vehicle model to measured test data for an existing vehicle combination's lateral stability according to driving tests as specified in ISO 14791. The comparison is made for the purpose of validating the simulation model for this type of test. A complete validation comprises the comparison for at least one tested vehicle and one variant of this vehicle, covered by a parameter variation in the vehicle model. The document appl...view more

This document specifies a method for comparing simulation results from a vehicle model to measured test data for an existing vehicle according to steady-state circular driving tests as specified in ISO 14792. The comparison is made for the purpose of validating the vehicle model for this type of test. This document applies to heavy vehicles, including commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with a maximum weigh...view more

This document describes a standard method for measuring a vehicle's longitudinal and lateral (horizontal plane) centre of gravity (CG) positions and three methods for estimating a vehicle's vertical CG position, the axle lift, tilt-table, and stable pendulum methods. It applies to heavy vehicles, that is commercial vehicles and buses as defined in ISO 3833 (trucks and trailers with maximum weight above 3,5 tonnes and buses and articulated buses with maximum weight above 5 tonnes, according to EC...view more

This document series describes a generic system for the exchange of data between truck chassis manufacturers and bodywork manufacturers. It applies to commercial vehicles as defined in ISO 3833, having a maximum gross vehicle mass above 3 500 kg. The process of exchanging the above information can involve: — chassis manufacturer; — chassis importer; — chassis dealer; — one or more bodywork manufacturers; and — bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loa...view more

This document series describes a generic system for the exchange of data between truck chassis manufacturers and bodywork manufacturers. It applies to commercial vehicles as defined in ISO 3833, having a maximum gross vehicle mass above 3 500 kg. The process of exchanging the above information can involve: — chassis manufacturer; — chassis importer; — chassis dealer; — one or more bodywork manufacturers; and — bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loa...view more

This document series describes a generic system for the exchange of data between truck chassis manufacturers and bodywork manufacturers. It applies to commercial vehicles as defined in ISO 3833, having a maximum gross vehicle mass above 3 500 kg. The process of exchanging product data can involve: — chassis manufacturer; — chassis importer; — chassis dealer; — one or more bodywork manufacturers; and — bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loading equi...view more

ISO 19377:2017 describes test methods for determining the deviation of the path travelled by a vehicle during a braking manoeuvre induced by an emergency braking system from a pre-defined desired path. The purpose of this document is the evaluation of the vehicle path during and following the system intervention. The corrective steering actions for keeping the vehicle on the desired path can be applied either by the driver or by a steering machine or by a driver assistance system. By making this...view more

This European Standard applies to body structures on commercial vehicles and on trailers.
This European Standard sets out basic minimum requirements for standard vehicle bodies (side walls, front and rear walls) and for reinforced vehicle bodies and specifies appropriate tests.
This standard applies to all commercial vehicles which are related by design and body type to the body structures described below.
Forces applied according to the test requirements described below can be invoked for lo...view more

ISO 18375:2016 describes an open-loop test method for determining the yaw stability of a vehicle on a low friction road surface. It applies to heavy vehicles, that is commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with maximum weight above 3,5 tonnes and buses and articulated buses with maximum weight above 5 tonnes, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4). The method is inten...view more

ISO 16552:2014 describes test methods for determining the stopping distance during a straight-line braking manoeuvre with the braking system fully operational. It applies to heavy vehicles equipped with an anti-lock braking system (ABS), including commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with maximum weight above 3,5 tonnes and buses and articulated buses with maximum weight above 5 tonnes, according to ECE and ...view more

The ISO 21308 series describes a generic system for the exchange of data between truck chassis manufacturers and bodywork manufacturers. It applies to commercial vehicles as defined in ISO 3833, having a maximum gross vehicle mass above 3 500 kg. The process of exchanging the above information can involve chassis manufacturers, chassis importers, chassis dealers, one or more bodywork manufacturers, and bodywork component suppliers, e.g. manufacturers of demountable bodies, cranes and loading equ...view more

ISO 14792:2011 specifies tests for determining the steady-state directional control response of heavy vehicles, one of the factors composing vehicle dynamics and road-holding properties. ISO 14792:2011 is applicable to heavy vehicles, i.e. commercial vehicles, combinations, buses and articulated buses as defined in ISO 3833, covered by Categories M3, N2, N3, O3, and O4 of UNECE (United Nations Economic Commission for Europe) and EC vehicle regulations. These categories pertain to trucks and trai...view more

ISO 16333:2011 specifies a tilt-table test method for estimating the steady-state rollover threshold of a heavy commercial vehicle or bus, i.e. the maximum lateral acceleration that the test vehicle could sustain in steady-state turning without rolling over. ISO 16333:2011 is applicable to complete roll units/combinations of roll-coupled vehicle units, e.g. single-unit vehicles, tractor semitrailer combinations, articulated buses, full trailers, B-train combinations, of commercial vehicles, comm...view more

ISO 14793:2011 specifies test methods for determining the transient response behaviour of heavy commercial vehicles, heavy commercial vehicle combinations, buses and articulated buses, as defined in ISO 3833 for trucks and trailers above 3,5 t and buses above 5 t maximum weight, and in UNECE (United Nations Economic Commission for Europe) and EC vehicle classification, categories M3, N2, N3, O3 and O4.

ISO 11026:2010 specifies an open-loop test method for determining the roll stability of a vehicle negotiating a curve on dry surface. It applies to heavy vehicles, that is commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with maximum weight above 3,5 t and buses and articulated buses with maximum weight above 5 t, according to ECE and EC vehicle classification, categories M3, N2, N3, O3 and O4). The method is intended f...view more

ISO 11012:2009 describes two open-loop test methods for determining on-centre handling characteristics of a vehicle in response to specific types of steering input under closely controlled test conditions: the weave test, and the transition test. ISO 11012:2009 applies to heavy vehicles, i.e. commercial vehicles, commercial vehicle combinations, buses and articulated buses as defined in ISO 3833 (trucks and trailers with maximum weight above 3,5 tonnes and buses and articulated buses with maximu...view more

ISO/TS 21308-4:2007 describes the mapping to STEP application protocol 239 for the exchange of dimensional data between truck chassis manufacturers and bodywork manufacturers. It applies to commercial vehicles, as defined in ISO 3833, which have a maximum gross vehicle mass greater than 3 500 kg. The process of exchanging the above information can involve the chassis manufacturer, the chassis importer, the chassis dealer, one or more bodywork manufacturers, and bodywork component suppliers, e.g....view more