79.060.99 - Other wood-based panels

ISO 13609:2014 establishes requirements for the specifications of blockboards and battenboards for general use, in dry, tropic dry/humid, and high-humid/exterior conditions. It includes requirements of materials, lay-up, physical and mechanical properties, bonding quality, formaldehyde release, conformity verification, and marking. The values listed in ISO 13609:2014 relate to product properties, but they are not characteristic values to be used in design calculations.

This European Standard sets the performance requirements of the following glued laminated products: - Glued laminated timber (glulam); - Glued solid timber; - Glulam with large finger joints; - Block glued glulam for use in buildings and bridges. It also lays down minimum production requirements, provisions for evaluation and attestation of conformity and marking of glued laminated products. This European Standard is applicable for glued laminated timber made of coniferous species listed in this...view more

This European Standard sets the performance requirements of the following glued laminated products:
-   Glued laminated timber (glulam);
-   Glued solid timber;
-   Glulam with large finger joints;
-   Block glued glulam
for use in buildings and bridges.
It also lays down minimum production requirements, provisions for evaluation and attestation of conformity and marking of glued laminated products.
This European Standard is applicable for glued laminated timber made of coniferous species listed ...view more

This European Standard specifies test methods for determining the following properties of structural timber and glued laminated timber: modulus of elasticity in bending; shear modulus; bending strength; modulus of elasticity in tension parallel to the grain; tension strength parallel to the grain; modulus of elasticity in compression parallel to the grain; compression strength parallel to the grain; modulus of elasticity in tension perpendicular to the grain; tension strength perpendicular to th...view more

This European Standard specifies requirements for solid wood panels as defined in EN 12775 with a maximum thickness of 80 mm for use in dry, humid and exterior conditions as defined in service classes 1, 2 and 3 of EN 1995-1-1.
Additional information on supplementary properties for certain applications is also given.

This European Standard specifies requirements for solid wood panels as defined in EN 12775 with a maximum thickness of 80 mm for use in dry, humid and exterior conditions as defined in service classes 1, 2 and 3 of EN 1995-1-1.
Additional information on supplementary properties for certain applications is also given.

ISO 10033-1:2011 specifies test methods for determining the bonding quality of Laminated Veneer Lumber (LVL) bonded with thermosetting resin.

This part of ISO 10033 specifies requirements for determining the bonding quality class of Laminated Veneer Lumber (LVL) bonded with thermosetting resins, according to their intended end uses.

This European Standard specifies a test method for determining the bonding quality of single-layer and multi-layer solid wood panels by a shear test.

This document gives definitions, a classification and specifies the requirements for Laminated Veneer Lumber (LVL) for general purposes or for use in construction in dry, humid or exterior conditions.
NOTE   This standard will be called up in EN 13986 for construction applications.
Annex A "Evaluation of the bonding quality of laminated veneer lumber" is normative
Information on supplementary properties is given in Annex B.

ISO 27567:2009 describes the methods for determining the thickness, length, width, spring, bow, twist and section squareness and cupping of test pieces of structural laminated veneer lumber (LVL), as specified in ISO 18776.

This European Standard provides information on the characteristic values for use in designing structures incorporating wood-based panels. The characteristic values given are as defined in EN 1995-1-1.
This standard includes the characteristic values of the mechanical properties and of the raw density for solid-wood panels complying with EN 13353.

This European Standard specifies a test method for determining the bonding quality of single-layer and multi-layer solid wood panels by a shear test.

This European Standard provides information on the characteristic values for use in designing structures incorporating wood-based panels. The characteristic values given are as defined in EN 1995-1-1.
This European Standard includes the characteristic values of the mechanical properties and of the raw density for solid-wood panels complying with EN 13353:2008 technical classes SWP/1 S, SWP/2 S, SWP/3 S.

ISO 18776:2008 specifies the requirements for Laminated Veneer Lumber (LVL) for general purposes and structural applications, in dry, tropical-dry/humid or high humidity/exterior conditions. Laminated Veneer Lumber (LVL) is a general description for an assembly of veneers laminated with an adhesive, in which the grain direction of the outer veneers and most other veneers is in the longitudinal direction. ISO 18776:2008 specifies requirements for the quality of veneers, bond durability, tolerance...view more

This document defines the characteristics of solid hardwood panelling and cladding elements with or without grooves and/or tongues, for interior or exterior use.
It does not cover characteristics of the possible coating system.
NOTE 1   Products sold in The European Economic Area will have to comply with prEN 14915.
NOTE 2   For softwood see EN 14519.

This European Standard specifies general requirements and appearance classes for both single layer and multi-layer solid wood panels, the latter with a minimum thickness of the outer layers of 3,5 mm, manufactured from hardwood species.

This European Standard specifies general requirements and appearance classes for both single-layer and multi-layer solid wood panels, the latter with a minimum thickness of the outer layers of 3,5 mm, manufactured from softwood species (e.g. spruce, pine, larch).