SIST EN 12369-3:2009
(Main)Wood-based panels - Characteristic values for structural design - Part 3: Solid-wood panels
Wood-based panels - Characteristic values for structural design - Part 3: Solid-wood panels
This European Standard provides information on the characteristic values for use in designing structures incorporating wood-based panels. The characteristic values given are as defined in EN 1995-1-1.
This standard includes the characteristic values of the mechanical properties and of the raw density for solid-wood panels complying with EN 13353.
Holzwerkstoffe - Charakteristische Werte für die Berechnung und Bemessung von Holzbauwerken - Teil 3: Massivholzplatten
Diese Europäische Norm gibt Informationen über charakteristische Werte für die Berechnung und Bemessung
von Bauwerken, in denen Holzwerkstoffe eingesetzt werden. Die angegebenen charakteristischen Werte
entsprechen den Definitionen in EN 1995-1-1.
Diese Norm enthält die charakteristischen Werte der mechanischen Eigenschaften und der Rohdichte von
Massivholzplatten der technischen Klassen SWP/1S, SWP/2S und SWP/3S nach EN 13353:2008.
Panneaux a base de bois - Valeurs caractéristiques pour la conception des structures - Partie 3: Bois panneautés
La présente Norme Européenne donne des informations sur les valeurs caractéristiques à utiliser dans la
conception des structures incorporant des panneaux à base de bois. Les valeurs caractéristiques données
sont telles que définies dans l’EN 1995-1-1.
La présente norme contient les valeurs caractéristiques des propriétés mécaniques et de la masse volumique
des bois panneautés répondant à l’EN 13353 :2008, classes techniques SWP/1 S, SWP/2 S, SWP/3 S.
Lesne plošče - Karakteristične vrednosti za dimenzioniranje konstrukcij - 3. del: Masivne lesne plošče
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Holzwerkstoffe - Charakteristische Werte für die Berechnung und Bemessung von Holzbauwerken - Teil 3: MassivholzplattenPanneaux a base de bois - Valeurs caractéristiques pour la conception des structures - Partie 3: Bois panneautésWood-based panels - Characteristic values for structural design - Part 3: Solid-wood panels79.060.99Other wood-based panelsICS:Ta slovenski standard je istoveten z:EN 12369-3:2008SIST EN 12369-3:2009en,fr,de01-april-2009SIST EN 12369-3:2009SLOVENSKI
STANDARD
SIST EN 12369-3:2009
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 12369-3November 2008ICS 79.060.99 English VersionWood-based panels - Characteristic values for structural design- Part 3: Solid-wood panelsPanneaux à base de bois - Valeurs caractéristiques pourconception des structures - Partie 3: Bois panneautésHolzwerkstoffe - Charakteristische Werte für dieBerechnung und Bemessung von Holzbauwerken - Teil 3:MassivholzplattenThis European Standard was approved by CEN on 12 October 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 12369-3:2008: ESIST EN 12369-3:2009
EN 12369-3:2008 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions and symbols.4 3.1 Terms and definitions.4 3.2 Symbols.5 3.2.1 Main Symbols.5 3.2.2 Subscripts.6 4 General.6 5 Characteristic values for solid wood panels.6 5.1 Introduction.6 5.2 Load-bearing panels for use in all service classes.7 Annex A (informative)
Presentation of characteristic values.9 Bibliography.10
SIST EN 12369-3:2009
EN 12369-3:2008 (E) 3 Foreword This document (EN 12369-3:2008) has been prepared by Technical Committee CEN/TC 112 “Wood-based panels”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2009, and conflicting national standards shall be withdrawn at the latest by May 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This European Standard is intended to be used in conjunction with EN 1995-1-1. This European Standard is one of a series specifying characteristic values of wood-based panels for structural design. The other parts of this series are listed in the Bibliography. Annex A is informative. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 12369-3:2009
EN 12369-3:2008 (E) 4 1 Scope This European Standard provides information on the characteristic values for use in designing structures incorporating wood-based panels. The characteristic values given are as defined in EN 1995-1-1. This European Standard includes the characteristic values of the mechanical properties and of the raw density for solid-wood panels complying with EN 13353:2008 technical classes SWP/1 S, SWP/2 S, SWP/3 S. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 338, Structural timber — Strength classes EN 789, Timber structures — Test methods — Determination of mechanical properties of wood based panels EN 1058, Wood-based panels — Determination of characteristics values of mechanical properties and density EN 1995-1-1, Eurocode 5: Design of timber structures — Part 1-1: General — Common rules and rules for buildings EN 13017-1, Solid wood panels — Classification by surface appearance — Part 1: Softwood EN 13017-2, Solid wood panels — Classification by surface appearance — Part 2: Hardwood EN 13353:2008, Solid wood panels (SWP) — Requirements 3 Terms and definitions and symbols 3.1 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1.1 characteristic values
3.1.1.1 characteristic strength value population 5-percentile value obtained from the results of tests with a duration of 300 s at an equilibrium moisture content of the test pieces relating to a temperature of 20 °C and a relative humidity of 65 % 3.1.1.2 characteristic stiffness value either the population 5-percentile or the mean value obtained of tests with a duration of 300 s at an equilibrium moisture content of the test pieces relating to a temperature of 20 °C and a relative humidity of 65 % NOTE The stiffness values given in the Tables are mean values as these are most commonly used in design. A note in Annex A explains how to calculate the 5-percentile value. 3.1.1.3 characteristic density population 5-percentile val
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.