SIST EN 13353:2009+A1:2011
(Main)Solid wood panels (SWP) - Requirements
Solid wood panels (SWP) - Requirements
This European Standard specifies requirements for solid wood panels as defined in EN 12775 with a maximum thickness of 80 mm for use in dry, humid and exterior conditions as defined in service classes 1, 2 and 3 of EN 1995-1-1.
Additional information on supplementary properties for certain applications is also given.
Massivholzplatten (SWP) - Anforderungen
Diese Europäische Norm legt Anforderungen an Massivholzplatten, definiert nach EN 12775, !mit einer Dicke von höchstens 80 mm" zur Verwendung im Trocken-, Feucht- und Außenbereich, definiert nach den Nut-zungsklassen 1, 2 und 3 nach EN 1995-1-1, fest. Es werden zusätzliche Informationen über weitere Eigenschaften für bestimmte Verwendungszwecke angege-ben.
Bois panneautés (SWP) - Exigences
La présente Norme européenne prescrit les exigences des bois panneautés tels que définis dans l’EN 12775
!avec une épaisseur maximale de 80 mm" pour utilisation en milieux sec, humide et extérieur comme
définis dans les classes de service 1, 2 et 3 de l’EN 1995-1-1.
Des informations supplémentaires sur des caractéristiques complémentaires pour certaines applications sont
également données.
Masivne lesne plošče (SWP) - Zahteve
Ta evropski standard določa zahteve za masivne lesne plošče, kot jih opredeljuje EN 12775, z največjo debelino 80 mm za uporabo v suhih, vlažnih in zunanjih pogojih, kot so opredeljeni v razredih storitev 1, 2 in 3 EN 1995-1-1. Podane so tudi dodatne informacije o dopolnilnih lastnostih za nekatere vrste uporabe.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Massivholzplatten (SWP) - AnforderungenBois panneautés (SWP) - ExigencesSolid wood panels (SWP) - Requirements79.060.99Other wood-based panelsICS:Ta slovenski standard je istoveten z:EN 13353:2008+A1:2011SIST EN 13353:2009+A1:2011en,fr,de01-september-2011SIST EN 13353:2009+A1:2011SLOVENSKI
STANDARDSIST EN 13353:20091DGRPHãþD
SIST EN 13353:2009+A1:2011
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13353:2008+A1
May 2011 ICS 79.060.99 Supersedes EN 13353:2008English Version
Solid wood panels (SWP) - Requirements
Bois panneautés (SWP) - Exigences
Massivholzplatten (SWP) - Anforderungen This European Standard was approved by CEN on 18 October 2008 and includes Amendment 1 approved by CEN on 9 March 2011.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2011 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13353:2008+A1:2011: ESIST EN 13353:2009+A1:2011
EN 13353:2008+A1:2011 (E) 2 Contents Page Foreword . 31Scope . 42Normative references . 43Terms, definitions and classes . 53.1Terms and definitions . 53.2Classes for solid wood panels indicating their intended use . 64Requirements . 64.1Dimensional tolerances . 64.2Moisture content at despatch . 64.3Bonding quality . 74.4Biological durability. 74.5Mechanical characteristics . 74.6Formaldehyde release . 95Supplementary properties . 96Verification of compliance . 96.1General . 96.2External control . 96.3Factory production control . 107Marking . 117.1Boards marketed within the European Economic Area for construction applications. 117.2Other boards . 11Annex A (normative)
Properties for structural and non-structural applications . 12Bibliography . 13
SIST EN 13353:2009+A1:2011
EN 13353:2008+A1:2011 (E) 3 Foreword This document (EN 13353:2008+A1:2011) has been prepared by Technical Committee CEN/TC 112 “Wood-based panels”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by November 2011, and conflicting national standards shall be withdrawn at the latest by November 2011. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document includes Amendment 1 approved by CEN on 9 March 2011. This document supersedes !EN 13353:2008". The start and finish of text introduced or altered by amendment is indicated in the text by tags
!". Compared to EN 13353:2003 the following changes have been made: a) classification introduced according to non-structural use, structural use and declared values; b) information on moisture content of chemically or thermally treated wood added in 4.2; c) relationship between shear strength and wood failure percentage in introduced in 4.3.3; d) provisions for adhesives other than thermosetting for structural applications added in 4.3.4; e) different requirements for single and multi layer solid wood panels for structural applications specified in 4.5.2; f) footnote regarding alternative test methods for the determination of the bonding quality added in Table 5. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following coun-tries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxem-bourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
SIST EN 13353:2009+A1:2011
EN 13353:2008+A1:2011 (E) 4 1 Scope This European Standard specifies requirements for solid wood panels as defined in EN 12775 !with a maximum thickness of 80 mm" for use in dry, humid and exterior conditions as defined in service classes 1, 2 and 3 of EN 1995-1-1. Additional information on supplementary properties for certain applications is also given. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 301:2006, Adhesives, phenolic and aminoplastic, for load-bearing timber structures — Classification and per-formance requirements EN 310, Wood-based panels — Determination of modulus of elasticity in bending and of bending strength EN 318, Wood-based panels — Determination of dimensional changes associated with changes in relative humid-ity EN 322, Wood-based panels — Determination of moisture content EN 323, Wood-based panels — Determination of density EN 324-1, Wood-based panels — Determination of dimensions of boards — Part 1: Determination of thickness, width and length EN 324-2, Wood-based panels — Determination of dimensions of boards — Part 2: Determination of squareness and edge straightness EN 326-1, Wood-based panels — Sampling, cutting and inspection — Part 1: Sampling and cutting of test pieces and expression of test results EN 326-2, Wood-based panels — Sampling, cutting and inspection — Part 2: Quality control in the factory EN 335-2, Durability of wood and wood-based products — Definition of use classes — Part 2: Application to solid wood EN 594, Timber structures — Test methods — Racking strength and stiffness of timber frame wall panels EN 596, Timber structures — Test methods — Soft body impact test of timber framed walls CEN/TS 635-4, Plywood — Classification by surface appearance — Part 4: Parameters of ability for finishing, guideline EN 717-2, Wood-based panels — Determination of formaldehyde release — Part 2: Formaldehyde release by the gas analysis method EN 789, Timber structures — Test methods — Determination of mechanical properties of wood-based panels EN 1058, Wood-based panels — Determination of characteristic values of mechanical properties and density ENV 1156, Wood-based panels — Determination of duration of load and creep factors EN 1195, Timber structures — Test methods — Performance of structural floor decking SIST EN 13353:2009+A1:2011
EN 13353:2008+A1:2011 (E) 5 EN 1995-1-1, Eurocode 5: Design of timber structures — Part 1-1: General — Common rules and rules for build-ings EN 12775, Solid wood panels — Classification and terminology EN 12871, Wood-based panels — Performance specifications and requirements for load bearing boards for use in floors, walls and roofs EN 13017-1, Solid wood panels — Classification by surface appearance — Part 1: Softwood EN 13017-2, Solid wood panels — Classification by surface appearance — Part 2: Hardwood EN 13183-2, Moisture content of a piece of sawn timber — Part 2: Estimation by electrical resistance method EN 13354, Solid wood panels — Bonding quality — Test method EN 13446, Wood-based panels — Determination of withdrawal capacity of fasteners EN 13986, Wood-based panels for use in construction — Characteristics, evaluation of conformity and marking !EN 15416-3:2007", Adhesives for load bearing timber structures other than phenolic and aminoplastic — Test methods — Part 3: Creep deformation test at cyclic climate conditions with specimens loaded in bending shear 3 Terms, definitions and classes 3.1 Terms and definitions For the purposes of this document, the terms and definitions given in EN 12775 and the following apply. 3.1.1 solid wood panel for use in dry conditions panel intended for use in interior applications with no risk of wetting as defined in service class 1 of EN 1995-1-1 and use class 1 of EN 335-2 NOTE Service class 1 is characterised by a moisture content of the material corresponding to a temperature of 20 °C and a relative humidity of the surrounding air exceeding 65 % for only a few weeks per year. 3.1.2 solid wood panel for use in humid conditions panel intended for use in protected external applications as defined in service class 2 of EN 1995-1-1 (e. g. behind cladding or under roof coverings) and use class 2 of EN 335-2 NOTE 1 It is also capable of resisting weather exposure for short periods (e.g. when exposed during construction). NOTE 2 Service class 2 is characterised by a moisture content of the material corresponding to a temperature of 20 °C and a relative humidity of the surrounding air exceeding 85 % for only a few weeks per year. 3.1.3 solid wood panel for use in exterior conditions panel intended for use in unprotected external applications as defined in service class 3 of EN 1995-1-1 and use class 3 of EN 335-2 NOTE 1 It is also capable of withstanding exposure to weathering conditions and liquid water, or water vapour in a damp but ventilated location where it can frequently attain a moisture content above 20 %. NOTE 2 Service class 3 is characterised by a moisture content of the material higher than service class 2. SIST EN 13353:2009+A1:2011
EN 13353:2008+A1:2011 (E) 6 3.2 Classes for solid wood panels indicating their intended use 3.2.1 Technical classes for non-structural use SWP/1 NS: Solid wood panel for non-structural use in dry conditions according to 3.1.1 SWP/2 NS: Solid wood panel for non-structural use in humid conditions according to 3.1.2 SWP/3 NS: Solid wood panel for non-structural use in exterior conditions according to 3.1.3 3.2.2 Technical classes for structural use SWP/1 S: Solid wood panel for structural use in dry conditions according to 3.1.1 SWP/2 S: Solid wood panel for structural use in humid conditions according to 3.1.2 SWP/3 S: Solid wood panel for structural use in exterior conditions according to 3.1.3 3.2.3 Classes for structural use based on declared values SWP/1 SD: Solid wood panel for structural use in dry conditions according to 3.1.1 SWP/2 SD: Solid wood panel for structural use in humid conditions according to 3.1.2 SWP/3 SD: Solid wood panel for structural use in exterior conditions according to 3.1.3 NOTE Technical classes are intended to simplify the use of standardised solid wood panels by providing supporting data e.g. in EN 12369-3 as well as simplifying marking in accordance with EN 13986. Nevertheless products should not be limited by the requirements according to the technical classes. Therefore classes based on declared values may be used for such prod-ucts. 4 Requirements 4.1 Dimensional tolerances The tolerances for the nominal length, width and thickness, thickness within the panel, edge
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.