SIST EN ISO 16486-2:2020
(Main)Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 2: Pipes (ISO 16486-2:2020)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U) piping systems with fusion jointing and mechanical jointing - Part 2: Pipes (ISO 16486-2:2020)
This part of ISO 16486 specifies the physical and mechanical properties of pipes made from unplasticized polyamide (PA-U) in accordance with ISO 16486-1, intended to be buried and used for the supply of gaseous fuels. It also specifies the test parameters for the test methods to which it refers.
ISO 16486 is applicable to PA-U piping systems the components of which are connected by fusion jointing and/or mechanical jointing.
In addition, it lays down dimensional characteristics and requirements for the marking of pipes.
Pipes conforming to this part of ISO 16486 are jointed typically by using mechanical, electrofusion or butt fusion (see Annex A) techniques, but not by solvent cement jointing.
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Rohrleitungssysteme aus weichmacherfreiem Polyamid (PA-U) mit Schweißverbindungen und mechanischen Verbindungen - Teil 2: Rohre (ISO 16486-2:2020)
Dieses Dokument legt die physikalischen und mechanischen Eigenschaften von Rohren fest, die nach ISO 16486 1 aus weichmacherfreiem Polyamid (PA-U) hergestellt sind, die unterirdisch verlegt und für die Gasversorgung verwendet werden. Es spezifiziert ebenso die Prüfparameter für die Prüfverfahren, auf die es sich bezieht.
Die Normenreihe ISO 16486 gilt für PA-U-Rohrleitungssysteme, deren Komponenten durch Schweiß-verbindungen und/oder mechanische Verbindungen zusammengefügt werden.
Außerdem legt dieses Dokument Maßeigenschaften und Anforderungen an die Kennzeichnung von Rohren fest.
Rohre, die diesem Dokument entsprechen, werden üblicherweise unter Verwendung von mechanischen, Elektroschweiß- oder Stumpfschweißtechniken zusammengefügt.
Systèmes de canalisations en matières plastiques pour la distribution de combustibles gazeux - Systèmes de canalisations en polyamide non plastifié (PA-U) avec assemblages par soudage et assemblages mécaniques - Partie 2: Tubes (ISO 16486-2:2020)
Le présent document spécifie les propriétés physiques et mécaniques des tubes en polyamide non plastifié (PA-U) conformément à l'ISO 16486-1, destinés à être enterrés et utilisés pour la distribution de combustibles gazeux. Il spécifie également les paramètres d'essai pour les méthodes d'essai auxquelles il fait référence.
La série de normes ISO 16486 s'applique aux systèmes de canalisations en PA-U dont les composants sont raccordés par des assemblages par soudage et/ou par des assemblages mécaniques.
De plus, ce document définit les caractéristiques dimensionnelles et les exigences pour le marquage des tubes.
Les tubes conformes au présent document sont généralement assemblés par des techniques mécaniques, par électrosoudage ou par soudage bout à bout.
Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Cevni sistemi iz nemehčanega poliamida (PA-U) z zvari in mehanskimi spoji - 2. del: Cevi (ISO 16486-2:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2020
Cevni sistemi iz polimernih materialov za oskrbo s plinastimi gorivi - Cevni sistemi
iz nemehčanega poliamida (PA-U) z zvari in mehanskimi spoji - 2. del: Cevi (ISO
16486-2:2020)
Plastics piping systems for the supply of gaseous fuels - Unplasticized polyamide (PA-U)
piping systems with fusion jointing and mechanical jointing - Part 2: Pipes (ISO 16486-
2:2020)
Kunststoff-Rohrleitungssysteme für die Gasversorgung - Rohrleitungssysteme aus
weichmacherfreiem Polyamid (PA-U) mit Schweißverbindungen und mechanischen
Verbindungen - Teil 2: Rohre (ISO 16486-2:2020)
Systèmes de canalisations en matières plastiques pour la distribution de combustibles
gazeux - Systèmes de canalisations en polyamide non plastifié (PA-U) avec
assemblages par soudage et assemblages mécaniques - Partie 2: Tubes (ISO 16486-
2:2020)
Ta slovenski standard je istoveten z: EN ISO 16486-2:2020
ICS:
75.200 Oprema za skladiščenje Petroleum products and
nafte, naftnih proizvodov in natural gas handling
zemeljskega plina equipment
83.140.30 Polimerne cevi in fitingi za Plastics pipes and fittings for
snovi, ki niso tekočine non fluid use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 16486-2
EUROPEAN STANDARD
NORME EUROPÉENNE
October 2020
EUROPÄISCHE NORM
ICS 75.200; 83.140.30
English Version
Plastics piping systems for the supply of gaseous fuels -
Unplasticized polyamide (PA-U) piping systems with
fusion jointing and mechanical jointing - Part 2: Pipes (ISO
16486-2:2020)
Systèmes de canalisations en matières plastiques pour Kunststoff-Rohrleitungssysteme für die Gasversorgung
la distribution de combustibles gazeux - Systèmes de - Rohrleitungssysteme aus weichmacherfreiem
canalisations en polyamide non plastifié (PA-U) avec Polyamid (PA-U) mit Schweißverbindungen und
assemblages par soudage et assemblages mécaniques - mechanischen Verbindungen - Teil 2: Rohre (ISO
Partie 2: Tubes (ISO 16486-2:2020) 16486-2:2020)
This European Standard was approved by CEN on 4 September 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 16486-2:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 16486-2:2020) has been prepared by Technical Committee ISO/TC 138
"Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee
CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by April 2021, and conflicting national standards shall be
withdrawn at the latest by April 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 16486-2:2020 has been approved by CEN as EN ISO 16486-2:2020 without any
modification.
INTERNATIONAL ISO
STANDARD 16486-2
Second edition
2020-09
Plastics piping systems for the supply
of gaseous fuels — Unplasticized
polyamide (PA-U) piping systems
with fusion jointing and mechanical
jointing —
Part 2:
Pipes
Systèmes de canalisations en matières plastiques pour la distribution
de combustibles gazeux — Systèmes de canalisations en polyamide
non plastifié (PA-U) avec assemblages par soudage et assemblages
mécaniques —
Partie 2: Tubes
Reference number
ISO 16486-2:2020(E)
©
ISO 2020
ISO 16486-2:2020(E)
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
ISO 16486-2:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.2 Abbreviated terms . 2
4 Compound . 2
5 General characteristics . 2
5.1 Appearance . 2
5.2 Colour . 3
5.3 Fusion compatibility . 3
6 Geometrical characteristics . 3
6.1 Measurement of dimensions . 3
6.2 Mean outside diameters, out-of-roundness and their tolerances . 3
6.3 Wall thicknesses and tolerances . 4
6.3.1 Minimum wall thickness . 4
6.3.2 Tolerances on wall thickness at any point . 5
7 Mechanical characteristics . 6
7.1 Conditioning . 6
7.2 Requirements . 6
8 Physical characteristics . 8
8.1 Conditioning . 8
8.2 Requirements . 8
9 Marking . 9
Annex A (normative) Squeeze-off technique .10
Annex B (informative) Examples of the water uptake over time as a function of the sample
thickness .11
Bibliography .14
ISO 16486-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 138, Plastics pipes, fittings and valves
for the transport of fluids, Subcommittee SC 4, Plastics pipes and fittings for the supply of g
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.