ASTM C1417M-00
(Specification)Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric)
Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric)
SCOPE
1.1 This specification covers the manufacture and acceptance of precast concrete pipe designed to conform to the owner's design requirements and to ASCE 15-93 or an equivalent design specification.
Note 1-The section on evaluation of core test results (14.3.3) and the Appendix are currently being reballoted.
1.2 This specification is SI companion to Specification C1417.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
Designation: C 1417M – 00
METRIC
Standard Specification for
Manufacture of Reinforced Concrete Sewer, Storm Drain,
1
and Culvert Pipe for Direct Design [Metric]
This standard is issued under the fixed designation C 1417M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope C 497 Test Methods for Concrete Pipe, Manhole Sections,
4
or Tile
1.1 This specification covers the manufacture and accep-
C 595 Specification for Blended Hydraulic Cements (Met-
tance of precast concrete pipe designed to conform to the
2
ric)
owner’s design requirements and to the ASCE 15-93 or an
C 618 Specification for Coal Fly Ash and Raw or Calcined
equivalent design specification.
Natural Pozzolan for Use as a Mineral Admixture in
NOTE 1—The section on evaluation of core test results (14.3.3) and the 3
Portland Cement Concrete
Appendix are currently being reballoted.
C 655 Specification for Reinforced Concrete D-Load Cul-
4
1.2 This specification is the SI companion to Specification
vert, Storm Drain, and Sewer Pipe
C 1417.
C 822 Terminology Relating to Concrete Pipe and Related
4
Products
2. Referenced Documents
2.2 Other Standards:
2.1 ASTM Standards:
ASCE 15-93 Standard Practice for the Direct Design of
A 82 Specification for Steel Wire, Plain, for Concrete Re-
Buried Precast Reinforced Concrete Pipe Using Standard
2
5
inforcement
Installations (SIDD)
A 185 Specification for Steel Welded Wire Fabric, Plain, for
ACI 318 Building Code Requirements for Reinforced Con-
2
6
Concrete Reinforcement
crete
A 496 Specification for Steel Wire, Deformed, for Concrete
2
3. Terminology
Reinforcement
A 497 Specification for Steel Welded Wire Fabric, De-
3.1 Definitions:
2
formed, for Concrete Reinforcement
3.1.1 For definitions of terms relating to concrete pipe, see
A 615/A 615M Specification for Deformed and Plain
Terminology C 822.
2
Billet-Steel Bars for Concrete Reinforcement
3.1.2 group of pipe sections—each day’s production run of
C 31 Practice for Making and Curing Concrete Test Speci-
pipe sections of a single concrete strength for a specific project.
3
mens in the Field
3.1.3 lot of pipe sections—total of the number of groups of
3
C 33 Specification for Concrete Aggregates
pipe sections of a single concrete strength produced for a
C 39 Test Method for Compressive Strength of Cylindrical
specific project.
3
Concrete Specimens
3.1.4 running average—average concrete compressive
C 76 Specification for Reinforced Concrete Culvert, Storm
strength of all groups of pipe sections of a single concrete
4
Drain, and Sewer Pipe
strength produced for a specific project, generally determined
2
C 150 Specification for Portland Cement
as each group is tested.
C 309 Specification for Liquid Membrane-Forming Com-
3
4. Basis of Acceptance of Design
pound for Curing Concrete
4.1 Manufacturing Design Data—The manufacturer shall
submit the following manufacturing design data for the con-
1
This specification is under the jurisdiction of ASTM Committee C13 on
crete pipe to the owner for approval.
Concrete Pipe and is the direct responsibility of Subcommittee C13.05 on Least
Cost Analysis.
Current edition approved June 10, 2000. Published September 2000. Originally
5
published as C 1417M–98. Last previous edition C 1417M–98. Available from American Society of Civil Engineers, 345 E. 45th Street, New
2
Annual Book of ASTM Standards, Vol 01.04. York, NY 10017–2398.
3 6
Annual Book of ASTM Standards, Vol 04.02. Available from American Concrete Institute, P.O. Box 19150, Detroit, MI
4
Annual Book of ASTM Standards, Vol 04.05. 48219.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
NOTICE: This standard has either been superceded and replaced by a new version or discontinued.
Contact ASTM International (www.astm.org) for the latest information.
C 1417M – 00
4.1.1 Pipe wall thickness. 6.2.3.3 Portland pozzolan cement only.
4.1.2 Concrete strength. 6.2.3.4 A combination of portland cement and fly ash or
4.1.3 Reinforcement: pozzolan, wherein the proportion of fly ash is between 5 and
4.1.3.1 Specification, 25 % by weight (mass) of total cementitious material (portland
4.1.3.2 Reinforcement Type 1, 2, or 3, where: cement plus fly ash).
6.3 Aggregates—Aggregates shall conform to the require-
Type 1: Smooth wire or plain bars
Type 2: Welded smooth wire fabric, 200 mm maximum spacing of
ments of Specification C 33, except that the requirement for
longitudinals
gradation shall not apply.
Type 3: Welded deformed wire fabric, deformed wire, deformed
bar
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.