CEN/TR 16626 gives guidance for the assessment of conformity of vitrified clay pipe systems for drains and sewers including pipes, fittings, manholes, perforated pipes, jacking pipes and associated products by the establishment of voluntary third-party certification procedures. It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001.

  • Technical report
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard applies for components for vitrified clay manholes and inspection chambers for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure. It specifies different strength classes and heights of sections. It also specifies the requirements for components used for joints, systems of joint dimensions and the materials rubber, polyurethane and polypropylene used for joints.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for vitrified clay pipes, fittings and flexible joints for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure. This standard also specifies requirements for rubber, polyurethane and polypropylene materials and other components used for jointing clay pipes and fittings. This standard specifies different strength classes, systems of joint dimensions, lengths and fittings. This standard does not apply to special fittings, adaptors and compatible accessories, perforated pipes and fittings, manholes and inspection chambers and pipes and joints for pipe jacking, which are specified in other parts of the standard series EN 295.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for perforated pipes and compatible fittings made from vitrified clay with or without sockets for the construction of land drains and drainage of waste tips. They are also used for percolation into the ground. This standard specifies different strength classes and areas of perforations.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for vitrified clay pipes and joints for pipe jacking for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure. Pipe jacking techniques include micro-tunnelling, pipe-eating, pipe bursting and where appropriate lining with discrete pipes. This standard also specifies requirements for rubber, polyurethane, polypropylene, stainless steel and other materials used for joints for pipe jacking.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for adaptors and connectors made from vitrified clay and/or other suitable materials for use with vitrified clay pipes and fittings for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure. Adaptors and connectors include insertable fittings, sealing rings for cut pipes and heat-shrinkable sleeves. This standard also applies for metal banded flexible couplings and adaptors and specifies requirements for rubber, polyurethane, stainless steel and other components used for them.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for the evaluation of conformity of products manufactured from vitrified clay and other materials(referred to as "products") specified in the following standards:
- pipes, fittings and joints according to EN 295-1;
- adapters, connectors and flexible couplings according to EN 295-4;
- perforated pipes and fittings according to EN 295-5;
- components of manholes and inspection chambers according to EN 295-6; and
- pipes and joints for pipe jacking according to EN 295-7.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for vitrified clay pipes and joints for pipe jacking for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure. Pipe jacking techniques include micro-tunnelling, pipe-eating, pipe bursting and where appropriate lining with discrete pipes.
This standard also specifies requirements for rubber, polyurethane, polypropylene, stainless steel and other materials used for joints for pipe jacking.
NOTE   Corresponding provisions for the evaluation of conformity (ITT and FPC) and sampling and those for the test methods are further specified in EN 295-2 and EN 295-3, respectively.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard applies for components for vitrified clay manholes and inspection chambers for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure.
It specifies different strength classes and heights of sections. It also specifies the requirements for components used for joints, systems of joint dimensions and the materials rubber, polyurethane and polypropylene used for joints.
NOTE 1   The specifiers/purchasers can select the components for vitrified clay manholes and inspection chambers according to their requirements.
This standard does not apply to manhole tops and cover slabs.
NOTE 2   Corresponding provisions for the evaluation of conformity (ITT and FPC) and sampling and those for the test methods are further specified in EN 295-2 and EN 295-3, respectively.

  • Standard
    21 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for perforated pipes and compatible fittings made from vitrified clay with or without sockets for use in land drains and drainage of waste tips. They are also used for percolation into the ground.
This standard specifies different strength classes and areas of perforations.
NOTE 1   The specifiers/purchasers can select perforated pipes and compatible fittings according to their requirements.
NOTE 2   Corresponding provisions for the evaluation of conformity (ITT and FPC) and sampling and those for the test methods are further specified in EN 295-2 and EN 295-3, respectively.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for the evaluation of conformity of products manufactured from vitrified clay and other materials (referred to as "products") specified in the following standards:
-   pipes, fittings and joints according to EN 295-1;
-   adapters, connectors and flexible couplings according to EN 295-4;
-   perforated pipes and fittings according to EN 295-5;
-   components of manholes and inspection chambers according to EN 295-6; and
-   pipes and joints for pipe jacking according to EN 295-7.

  • Standard
    38 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for adaptors and connectors made from vitrified clay and/or other suitable materials for use with vitrified clay pipes and fittings for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure.
Adaptors and connectors include insertable fittings, sealing rings for cut pipes and heat-shrinkable sleeves.
This standard also applies for metal banded flexible couplings and adaptors and specifies requirements for rubber, polyurethane, stainless steel and other components used for them.
NOTE 1   The specifiers/purchasers can select adaptors, connectors and flexible couplings according to their requirements.
NOTE 2   Corresponding provisions for the evaluation of conformity (ITT and FPC) and sampling and those for the test methods are further specified in EN 295 2 and EN 295 3, respectively.

  • Standard
    29 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for vitrified clay pipes, fittings and flexible joints for buried drain and sewer systems for the conveyance of wastewater (including domestic wastewater, surface water and rainwater) under gravity and periodic hydraulic surcharge or under continuous low head of pressure.
This standard also specifies requirements for rubber, polyurethane and polypropylene materials and other components used for jointing clay pipes and fittings.
This standard specifies different strength classes, systems of joint dimensions, lengths and fittings.
NOTE 1   The specifiers/purchasers can select them according to their requirements.
This standard does not apply to special fittings, adaptors and compatible accessories, perforated pipes and fittings, manholes and inspection chambers and pipes and joints for pipe jacking, which are specified in other parts of the standard series EN 295.
NOTE 2   Corresponding provisions for the evaluation of conformity (ITT and FPC) and sampling and those for the test methods are further specified in EN 295-2 and EN 295-3, respectively.

  • Standard
    34 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part of this European Standard is the specification for the methods of test for requirements of EN 295-1. Note: Where reference is made to clauses in EN 295-1 it is clearly stated.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies requirements for testing of products manufactured from vitrified clay and other materials specified in the following standards:
   pipes, fittings and joints according to EN 295-1;
   adaptors, connectors and flexible couplings according to EN 295-4;
   perforated pipes and fittings according to EN 295-5;
   components of manholes and inspection chambers according to EN 295 6;
   pipes and joints for pipe jacking according to EN 295-7.

  • Standard
    42 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard applies to pipes and fittings made from polyester resin concrete (PRC, see 3.1.23), intended to be used within a drain or sewer system operating without pressure. It applies to products for use in buried installations to be installed by open-trench techniques or pipe jacking.
It applies to pipes, fittings and their joints of nominal sizes from DN 150 to DN 3000 for circular cross-sections, from WN/HN 300/450 to WN/HN 1400/2100 for egg-shaped cross-sections and from DN 800 to DN 1800 for kite-shaped cross-sections.
The intended use of these products is for the conveyance of sewage, rainwater and surface water at temperatures up to 50 °C, without pressure or occasionally at a head of pressure up to 0,5 bar ), and installed in areas subjected to vehicle and/or pedestrian traffic.
NOTE 1   The attention of readers is drawn to applicable requirements contained in EN 476.
It specifies definitions, requirements and characteristics of pipes, fittings, joints, materials, test methods and marking.
The pipes are classified on the basis of the intended method of installation and cross-sectional shape.
NOTE 2   It is the responsibility of the purchaser or specifier to make the appropriate selections, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    80 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC Correction of Figure I.1 (this third Corrigendum to EN 1916:2002 contains the text of AC1, AC2 and AC3)

  • Corrigendum
    24 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day

TC Correction of Figure I.1 (this third Corrigendum to EN 1916:2002 contains the text of AC1, AC2 and AC3)

  • Corrigendum
    24 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies performance requirements as defined in table 1 and describes test methods for precast concrete pipes and fittings, unreinforced, steel fibre and reinforced, with flexible joints (with seals either integrated in the units or supplied separately) and nominal sizes not exceeding DN 3200 for units with a circular bore or WN/HN 1400/2100 for units with an egg-shaped bore, for which the main intended use is the conveyance of sewage, rainwater and surface water under gravity or occasionally at low head of pressure, in pipelines that are generally buried.

  • Standard
    90 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies performance requirements as defined in table 1 and describes test methods for precast concrete pipes and fittings, unreinforced, steel fibre and reinforced, with flexible joints (with seals either integrated in the units or supplied separately) and nominal sizes not exceeding DN 3200 for units with a circular bore or WN/HN 1400/2100 for units with an egg-shaped bore, for which the main intended use is the conveyance of sewage, rainwater and surface water under gravity or occasionally at low head of pressure, in pipelines that are generally buried.

  • Standard
    90 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Standard gives specifications for asbestos free fibre-cement manholes and inspection chambers for use in buried drains and sewers with gravity flow at atmospheric pressure.  
Products covered by this standard include prefabricated elements in as well as prefabricated complete manholes and inspection chambers.
It specifies definitions, descriptions, composition, general appearance and finish, geometrical characteristics, mechanical characteristics, acceptance tests, type tests and quality control requirements.
NOTE   Complete manholes or prefabricated elements may also be used for other purposes such as pumping stations, items of drainage, items for sewage treatment or sewage disposal, when corresponding additional requirements according to the relevant European Standards are fulfilled.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Sstandard applies to fibre-cement pipes, joints and fittings used for sewerage and rainwater discharge systems for buildings where pressure tight joints are required. It defines general composition, classification, geometrical, mechanical and physical characteristics and quality control.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This draft European Standard, applies to both types of fibre-cement pipes AT and NT as defined in EN 512:1994, gives installation recommendations for this pipelines in above or below ground situations. It complements the general principles for all types of water supply systems specified in EN 805:2000, "Water supply - Requirements for systems and components outside buildings", and should be used in conjunction with that standard. This standard gives guidance in on-site working methods and in the selection and use of approved tools for cutting and machining fibre-cement pipes. This standard does not cover the following : a) installation by thrust boring and pipe jacking methods which require the use of highly specialized techniques ; b) problems caused by the use of special installations procedures (e.g. removal of pile sheeting in very deep trenches, etc.).

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Migrated from Progress Sheet (TC Comment) (2000-07-10): Under UAP following BT C115/2000

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Migrated from Progress Sheet (TC Comment) (2000-07-10): Under UAP following BT C115/2000
2020-01-20: Originator of XML version: NEN (on behalf of NEN, ASI, DS, SFS, SIS, SN)

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This draft European Standard, applies to both types of fibre-cement pipes AT and NT as defined in EN 512:1994, gives installation recommendations for this pipelines in above or below ground situations. It complements the general principles for all types of water supply systems specified in EN 805:2000, "Water supply - Requirements for systems and components outside buildings", and should be used in conjunction with that standard. This standard gives guidance in on-site working methods and in the selection and use of approved tools for cutting and machining fibre-cement pipes. This standard does not cover the following : a) installation by thrust boring and pipe jacking methods which require the use of highly specialized techniques ; b) problems caused by the use of special installations procedures (e.g. removal of pile sheeting in very deep trenches, etc.).

  • Standard
    39 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the essential requirements for compatibility and interchangeability of borosilicate glass plant, piping and fittings from DN 15 to DN 1000.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Sstandard applies to fibre-cement pipes, joints and fittings used for sewerage and rainwater discharge systems for buildings where pressure tight joints are required. It defines general composition, classification, geometrical, mechanical and physical characteristics and quality control.

  • Standard
    60 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the essential requirements for compatibility and interchangeability of borosilicate glass plant, piping and fittings from DN 15 to DN 1000.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part 1 of EN 588 specifies requirements for fibre-cement pipes, joints and fittings suitable for gravity systems at atmospheric pressure intended for sewerage and drainage applications. It is applicable only to the more commonly used fittings i.e. angled branches or tees and bends. It defines general composition, classification, geometrical, mechanical and physical characteristics, acceptance tests and type tests.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the characteristics of fibre-cement pipes and joints for use under pressure for conveying potable and non potable water and sewage. It is concerned with composition, classification, geometrical, mechanical and physical characteristics, acceptance tests and type tests.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This part 1 of EN 588 specifies requirements for fibre-cement pipes, joints and fittings suitable for gravity systems at atmospheric pressure intended for sewerage and drainage applications. It is applicable only to the more commonly used fittings i.e. angled branches or tees and bends. It defines general composition, classification, geometrical, mechanical and physical characteristics, acceptance tests and type tests.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard covers the requirements and manufacture of circumferentially reinforced concrete pressure pipe, without steel cylinder and not circumferentially prestressed, with steel reinforcement (RCP) or a homogeneouslydistributed reinforcement composed of multiple layers of small diameter wires (DRP). Pipes shall have diameter ranging DN/ID 300 to DN/ID 4000. Larger size could be manufactured based on the concepts of this standard.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies common requirements for the following components : concrete pressure pipes, joints and fittings including jacking pipes. These components are intended to be used in water systems which carry water for human consumption, industrial purposes, irrigation or waste water.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the requirements and manufacture of reinforced concrete pressure pipe cylinder type, that is not prestressed, in sizes from DN/ID 250 to DN/ID 4000 inclusive. Pretensioned concrete cylinder pipe, in whichthe reinforcement is wrapped, under low tension, directly on to the steel cylinder is covered by this standard and is not normally manufactured in sizes above DN/ID 1400. Larger sizes can be manufactured based on the concepts of thisstandard.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard covers the requirements and the manufacture of prestressed concrete cylinder pressure pipes and fittings in sizes from DN/ID 500 to DN/ID 4000 inclusive. Larger sizes could be manufactured based on the concepts of thisstandard. These types of pipes are designed for the internal pressure, external loads and bedding conditions designated by the purchaser.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard covers the requirements and the manufacture of prestressed concrete cylinder pressure pipes and fittings in sizes from DN/ID 500 to DN/ID 4000 inclusive. Larger sizes could be manufactured based on the concepts of thisstandard. These types of pipes are designed for the internal pressure, external loads and bedding conditions designated by the purchaser.

  • Standard
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies common requirements for the following components : concrete pressure pipes, joints and fittings including jacking pipes. These components are intended to be used in water systems which carry water for human consumption, industrial purposes, irrigation or waste water.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This European Standard specifies the requirements and manufacture of reinforced concrete pressure pipe cylinder type, that is not prestressed, in sizes from DN/ID 250 to DN/ID 4000 inclusive. Pretensioned concrete cylinder pipe, in whichthe reinforcement is wrapped, under low tension, directly on to the steel cylinder is covered by this standard and is not normally manufactured in sizes above DN/ID 1400. Larger sizes can be manufactured based on the concepts of thisstandard.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the characteristics of fibre-cement pipes and joints for use under pressure for conveying potable and non potable water and sewage. It is concerned with composition, classification, geometrical, mechanical and physical characteristics, acceptance tests and type tests.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day

TC - Various modifications throughout text

  • Corrigendum
    19 pages
    English, French and German language
    sale 10% off
    e-Library read for
    1 day

Vitrified clay pipes and fittings and pipe joints for drains and sewers - Part 5: Requirements for perforated vitrified clay pipes and fittings Amendment of EN 295-5:1994.

  • Amendment
    6 pages
    English language
    sale 10% off
    e-Library read for
    1 day

Migrated from Progress Sheet (TC Comment) (2000-07-10): Amendment to the part 1

  • Amendment
    4 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This Standard specifies the requirements for components for vitrified clay manholes and inspection shafts. These are for use with flexibly jointed vitrified clay pipes and fittings manufactured to EN 295-1. Where this standard provides different systems of jointing, different heights, different strength classes and different channels, the specifiers/purchasers may select according to their requirements. Note: Where reference is made to clauses in EN 295-1, EN 295-2 or EN 295-3 this is clearly stated.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the performance criteria for the internal pressure strength, the external pressure strength, the longitudinal bending strength, the crushing resistance, the tightness, the resistance to abrasion and the permeability to pollutants of pipes used for waste liquid (above all water) transport. This standard includes the corresponding test methods and the evalutation of conformity of the product to this standard.

  • Standard
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies requirements for flexibly jointed vitrified clay pipes for the construction of pipelines by pipe jacking techniques including micro-tunnelling, pipe-eating, pipe bursting and where appropriate for slip-lining. Where this standard provides for different strength classes the specifiers/purchasers may select according to their requirments.

  • Standard
    20 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies the performance criteria for the internal pressure strength, the external pressure strength, the longitudinal bending strength, the crushing resistance, the tightness, the resistance to abrasion and the permeability to pollutants of pipes used for waste liquid (above all water) transport. This standard includes the corresponding test methods and the evaluation of conformity of the product to this standard.

  • Standard
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day

This standard specifies requirements for vitrified clay pipes, fittings and pipe joints for drains and sewers to be in conformance with the requirements of the Mandate M 118 "Waste Water Engineering Products" as well as the Mandate M 131 "Pipes, Tanks and Ancillaries not in contact with water for human consumption"
In this scope it applies to:
- vitrified clay pipes, fittings and pipe joints
- special fittings, adaptors and compatible accessories
- perforated vitrified clay pipes and fittings
- vitrified clay manholes and
- vitrified clay pipes and joints for pipe jacking
for drain or sewer systems for the conveyance of sewage and surface water (including rain water) under gravity or occasionally at low head of pressure.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day