ASTM C1932-23
(Specification)Standard Specification for Manufacture of Reinforced Precast Concrete End Sections for Pipe
Standard Specification for Manufacture of Reinforced Precast Concrete End Sections for Pipe
SCOPE
1.1 This specification covers the manufacture and acceptance of reinforced precast concrete end sections for pipe, herein referred to as “end section(s),” to conform to the owner's requirements.
Note 1: End sections include but are not limited to; flared end sections; sloped end sections; parallel end sections, precast end walls; precast headwalls; etc. (see Fig. 1 for examples); or as designated by the owner.
FIG. 1 Examples of Various Precast End Sections for Pipe
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
Note 2: This specification is a purchasing, manufacturing and acceptance specification and does not include requirements for bedding, backfill or installation. Care should be taken in assuring that the installation conforms to the project construction specifications.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C1932 − 23
Standard Specification for
Manufacture of Reinforced Precast Concrete End Sections
1
for Pipe
This standard is issued under the fixed designation C1932; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope A706/A706M Specification for Deformed and Plain Low-
Alloy Steel Bars for Concrete Reinforcement
1.1 This specification covers the manufacture and accep-
A820/A820M Specification for Steel Fibers for Fiber-
tance of reinforced precast concrete end sections for pipe,
Reinforced Concrete
herein referred to as “end section(s),” to conform to the
A1064/A1064M Specification for Carbon-Steel Wire and
owner’s requirements.
Welded Wire Reinforcement, Plain and Deformed, for
NOTE 1—End sections include but are not limited to; flared end
Concrete
sections; sloped end sections; parallel end sections, precast end walls;
C33/C33M Specification for Concrete Aggregates
precast headwalls; etc. (see Fig. 1 for examples); or as designated by the
C39/C39M Test Method for Compressive Strength of Cylin-
owner.
drical Concrete Specimens
1.2 The values stated in inch-pound units are to be regarded
C150/C150M Specification for Portland Cement
as standard. The values given in parentheses are mathematical
C260/C260M Specification for Air-Entraining Admixtures
conversions to SI units that are provided for information only
for Concrete
and are not considered standard.
C309 Specification for Liquid Membrane-Forming Com-
NOTE 2—This specification is a purchasing, manufacturing and accep-
pounds for Curing Concrete
tance specification and does not include requirements for bedding, backfill
C494/C494M Specification for Chemical Admixtures for
or installation. Care should be taken in assuring that the installation
Concrete
conforms to the project construction specifications.
C497/C497M Test Methods for Concrete Pipe, Concrete
1.3 This standard does not purport to address all of the
Box Sections, Manhole Sections, or Tile
safety concerns, if any, associated with its use. It is the
C595/C595M Specification for Blended Hydraulic Cements
responsibility of the user of this standard to establish appro-
C618 Specification for Coal Fly Ash and Raw or Calcined
priate safety, health, and environmental practices and deter-
Natural Pozzolan for Use in Concrete
mine the applicability of regulatory limitations prior to use.
C822 Terminology Relating to Concrete Pipe and Related
1.4 This international standard was developed in accor-
Products
dance with internationally recognized principles on standard-
C989/C989M Specification for Slag Cement for Use in
ization established in the Decision on Principles for the
Concrete and Mortars
Development of International Standards, Guides and Recom-
C1017/C1017M Specification for Chemical Admixtures for
mendations issued by the World Trade Organization Technical
3
Use in Producing Flowing Concrete (Withdrawn 2022)
Barriers to Trade (TBT) Committee.
C1602/C1602M Specification for Mixing Water Used in the
Production of Hydraulic Cement Concrete
2. Referenced Documents
C1837 Specification for Production of Dry Cast Concrete
2
2.1 ASTM Standards:
Used for Manufacturing Pipe, Box, and Precast Structures
A615/A615M Specification for Deformed and Plain Carbon-
D7508/D7508M Specification for Polyolefin Chopped
Steel Bars for Concrete Reinforcement
Strands for Use in Concrete
3. Terminology
1
This test method is under the jurisdiction of ASTM Committee C13 on
3.1 Definitions:
Concrete Pipe and is the direct responsibility of Subcommittee C13.05 on Special
Projects. 3.1.1 For definitions of terms relating to concrete pipe, see
Current edition approved Feb. 1, 2023. Published February 2023. DOI: 10.1520/
Terminology C822.
C1932-23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
3
Standards volume information, refer to the standard’s Document Summary page on The last approved version of this historical standard is referenced on www.ast-
the ASTM website. m.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1932 − 23
FIG. 1 Examples of Various Precast End Sections for Pipe
3.1.2 precast concrete end section, n—a reinforced precast 5.2 When mutually agreed in writing by the owner and the
concrete structure utilized at the inlet or ou
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.