iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D5367-08

(Practice)

Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted

Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted

SIGNIFICANCE AND USE
Water-blast cleaning with, (SSPC-TR2/NACE 6C 198) or without, (SSPC-SP 12/NACE No. 5) abrasive, results in flash rusting under some environmental conditions. Inhibitors are used to prevent flash rusting while drying and before coating application. The inhibitor or reaction products of the inhibitor on the substrate becomes part of the coating systems. Coating performance may be influenced by the inhibitor. Soluble contaminants or unreacted inhibitors left on the surface under the coating may cause premature failure. This practice includes a comparison of coating performance with and without inhibitors using various laboratory tests to simulate a range of conditions such as high moisture, marine atmospheric or water immersion.
The user or specifier must determine the specific test methods to be used and exposure conditions. Some test methods referenced may not be applicable to all types of coatings.
SCOPE
1.1 This practice covers procedures to evaluate the compatibility of coatings with inhibitors used to prevent flash rusting of steel before application of coatings.
1.2 The inhibitors are used with water-blast cleaning surface preparation and may be used with or without abrasives.
1.3 The manufacturer of the coatings shall be consulted to ensure compatibility of inhibitors with the coatings.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Dec-2007
ICS
87.040 - Paints and varnishes
Technical Committee
D33 - Protective Coating and Lining Work for Power Generation Facilities
Drafting Committee
D33.05 - Application and Surface Preparation
Current Stage
Ref Project

Buy Standard

ASTM D5367-08 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive BlastedASTM D5367-08 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted
PreviousNext
Standard
ASTM D5367-08 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview
REDLINE ASTM D5367-08 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive BlastedREDLINE ASTM D5367-08 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted
PreviousNext
Standard
REDLINE ASTM D5367-08 - Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D5367 − 08
Standard Practice for
Evaluating Coatings Applied Over Surfaces Treated With
Inhibitors Used to Prevent Flash Rusting of Steel When
1
Water or Water/Abrasive Blasted
This standard is issued under the fixed designation D5367; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope D4541 Test Method for Pull-Off Strength of Coatings Using
Portable Adhesion Testers
1.1 This practice covers procedures to evaluate the compat-
2.2 Other Standards:
ibility of coatings with inhibitors used to prevent flash rusting
SSPC-SP 5 Surface Preparation Specification No. 5, White
of steel before application of coatings.
3
Metal Blast Cleaning
1.2 Theinhibitorsareusedwithwater-blastcleaningsurface
SSPC-SP12/NACE No. 5 Surface Preparation and Cleaning
preparation and may be used with or without abrasives.
of Steel and Other Hard Materials by High and Ultrahigh-
3
1.3 The manufacturer of the coatings shall be consulted to Pressure Water Jetting Prior to Recoating
3
ensure compatibility of inhibitors with the coatings. SSPC-TR2/NACE 6C 198 Wet Abrasive Blast Cleaning
NACE TM-01-74 Laboratory Method for Evaluation of
1.4 This standard does not purport to address all of the
Protective Coatings Used as Lining Materials in Immer-
safety concerns, if any, associated with its use. It is the
4
sion Surfaces
responsibility of the user of this standard to establish appro-
priate safety and health practices and determine the applica-
3. Significance and Use
bility of regulatory limitations prior to use.
3.1 Water-blast cleaning with, (SSPC-TR2/NACE 6C 198)
2. Referenced Documents or without, (SSPC-SP 12/NACE No. 5) abrasive, results in
2 flash rusting under some environmental conditions. Inhibitors
2.1 ASTM Standards:
are used to prevent flash rusting while drying and before
A36/A36M Specification for Carbon Structural Steel
coating application. The inhibitor or reaction products of the
B117 Practice for Operating Salt Spray (Fog) Apparatus
inhibitor on the substrate becomes part of the coating systems.
D714 Test Method for Evaluating Degree of Blistering of
Coating performance may be influenced by the inhibitor.
Paints
Solublecontaminantsorunreactedinhibitorsleftonthesurface
D822 Practice for Filtered Open-Flame Carbon-Arc Expo-
under the coating may cause premature failure. This practice
sures of Paint and Related Coatings
includes a comparison of coating performance with and with-
D1193 Specification for Reagent Water
out inhibitors using various laboratory tests to simulate a range
D1654 Test Method for Evaluation of Painted or Coated
of conditions such as high moisture, marine atmospheric or
Specimens Subjected to Corrosive Environments
water immersion.
D2247 Practice for Testing Water Resistance of Coatings in
100 % Relative Humidity 3.2 The user or specifier must determine the specific test
methods to be used and exposure conditions. Some test
D3359 Test Methods for Measuring Adhesion by Tape Test
D4417 Test Methods for Field Measurement of Surface methods referenced may not be applicable to all types of
Profile of Blast Cleaned Steel coatings.
4. Specimen Preparation
1
This practice is under the jurisdiction of ASTM Committee D33 on Protective
4.1 Carbon steel samples of an appropriate size, in accor-
Coating and Lining Work for Power Generation Facilities and is the direct
dance with Specification A36/A36M for the specified test
responsibility of Subcommittee D33.05 on Application and Surface Preparation.
method shall be white metal blast-cleaned in accordance with
Current edition approved Jan. 1, 2008. Published January 2008. Originally
approved in 1994. Last previous edition approved in 2000 as D5367 – 00. DOI:
10.1520/D5367-08.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Pittsburgh, PA 15222-4656, http://www.sspc.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from National Association of Corrosion Engineers (NACE), 1440
the ASTM website. South Creek Dr., Houston, TX 77084-4906, http://www.nace.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
D5367 − 08
TABLE 1 Recommended Exposure Tests and Examination
SSPC-SP 5 and measure profile in accordance with Test
Schedules
Methods D4417. Select an abrasive that is suitable for use with
Guide to
water-blas
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:D5367–00 Designation:D5367–08
Standard Practice for
Evaluating Coatings Applied Over Surfaces Treated With
Inhibitors Used to Prevent Flash Rusting of Steel When
1
Water or Water/Abrasive Blasted
This standard is issued under the fixed designation D 5367; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1This practice covers procedures to evaluate the compatibility of coatings with inhibitors used with water-blast cleaning
surface preparation with or without abrasive to prevent flash rusting of steel prior to application of coatings.
1.2The manufacturer of the coatings shall be consulted to ensure compatibility of inhibitors with the coatings.
1.3
1.1 Thispracticecoversprocedurestoevaluatethecompatibilityofcoatingswithinhibitorsusedtopreventflashrustingofsteel
before application of coatings.
1.2 The inhibitors are used with water-blast cleaning surface preparation and may be used with or without abrasives.
1.3 The manufacturer of the coatings shall be consulted to ensure compatibility of inhibitors with the coatings.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
2
2.1 ASTM Standards:
A36/36M 36/A 36M Specification for Carbon Structural Steel
B 117 Practice for Operating Salt Spray (Fog) Testing Apparatus
D 714 Test Method for Evaluationg Degree of Blistering of Paints
D 822Practice for Conducting Tests on Paint and Related Coatings and Materials Using Filtered Open-Flame Carbon-Arc Light
4
and Water Exposure Apparatus Practice for Filtered Open-Flame Carbon-Arc Exposures of Paint and Related Coatings
D 1193 Specification for Reagent Water
D 1654 Test Method for Evaluation of Painted or Coated Specimens Subjected to Corrosive Environments
D 2247 Practice for Testing Water Resistance of Coatings in 100 % Relative Humidity
D 3359 Test Methods for Measuring Adhesion by Tape Test
D 4417 Test Methods for Field Measurement of Surface Profile of Blast Cleaned Steel
D 4541 Test MethodsMethod for Pull-Off Strength of Coatings Using Portable Adhesion Testers
2.2 Other Standards:
3
SSPC-SP 5 Surface Preparation Specification No. 5, White Metal Blast Cleaning
SSPC-SP12/NACE No. 5 Surface Preparation and Cleaning of Steel and Other Hard Materials by High and Ultrahigh-Pressure
3
Water Jetting Prior to Recoating
3
SSPC-TR2/NACE 6C 198 Wet Abrasive Blast Cleaning
4
NACE TM-01-74 Laboratory Method for Evaluation of Protective Coatings Used as Lining Materials in Immersion Surfaces
1
This practice is under the jurisdiction ofASTM Committee D33 on Protective Coating and Lining Work for Power Generation Facilities and is the direct responsibility
of Subcommittee D33.05 on Application and Surface Preparation.
Current edition approved Dec. 10, 2000.Jan. 1, 2008. Published February 2001.January 2008. Originally published as D5367–94.approved in 1994. Last previous edition
D5367–94.approved in 2000 as D 5367 – 00.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book ofASTM Standards
, Vol 01.04.volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Annual Book of ASTM Standards, Vol 03.02
3
Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor, Pittsburgh, PA 15222-4656, http://www.sspc.org.
4
Annual Book of ASTM Standards, Vol 06.01.
4
Available from National Association of Corrosion Engineers (NACE), 1440 South Creek Dr., Houston, TX 77084-4906, http://www.nace.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D5367–08
3. Significance and Use
3.1 Water-blast cleaning with, (SSPC-TR2/NACE 6C 198)198) or without, (SSPC-SP 12/Nace12/NACE No. 5)5) abrasive,
results in flash rusting under some environmental conditions. Inhibitors are used to prevent flash rusting while drying and before
coatingapplication.Theinhibitororreactionproductsoftheinhibitoronthesubstratebecomespartofthecoatingsystems.Coating
performan
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3912-10(2023)(Test Method)
Standard Test Method for Chemical Resistance of Coatings and Linings for Use in Nuclear Power Plants

SIGNIFICANCE AND USE
3.1 The lining test described in 6.2 may be used to evaluate the chemical resistance characteristics of coating systems for lining surfaces of tanks, vessels and similar facilities used in Coating Service Level I and II applications in a nuclear power plant. For the evaluation of linings in Coating Service Level III water immersion applications in nuclear power plants use the test methods and guidance found in Guide D7230.  
3.2 The specific chemical resistance tests described in 6.1 are dependent upon the relative severity of the service conditions. The specific chemical reagents to be used shall be specified to reflect the intended service conditions.  
3.3 At the discretion of the user, the methods presented may also be used to evaluate coatings and linings for applications in other types of power plants or other industrial services.
SCOPE
1.1 This test method establishes procedures for the evaluation of the chemical resistance of coatings and linings for use in Coating Service Level I and II applications in nuclear power plants.  
1.2 This test method is intended to be used as a screening test to evaluate coatings and linings on steel and concrete substrates.  
1.3 This test method addresses two exposure intervals:
(1) Short Term (Typically 5 days): Such exposures are primarily applicable for coatings exposed to chemical splash or spill.
(2) Long Term (Typically 180 days): Such exposures are primarily applicable for linings exposed to continuous or near-continuous chemical immersion.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D4082-10(2023)(Test Method)
Standard Test Method for Effects of Gamma Radiation on Coatings for Use in Nuclear Power Plants

SIGNIFICANCE AND USE
4.1 This test method is designed to provide a uniform test to assess the suitability of coatings, used in nuclear power facilities, under radiation exposure for the life of the facilities, including radiation during a DBA (Coating Service Level I areas only). Specific plant radiation exposure may exceed or be less than the amount specified in 7.2 of this standard. If required by the licensee design basis, the gamma dose used may exceed the actual anticipated plant gamma dose to account for beta dose. Coatings in Level II and III areas (outside primary containment) are expected to be exposed to lower accumulated radiation doses.
SCOPE
1.1 This test method covers a standard procedure for evaluating the lifetime radiation tolerance of coatings to be used in nuclear power plants. This test method is applicable to Coating Service Levels I, II, and III.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM D5367-16(2021)(Practice)
Standard Practice for Evaluating Coatings Applied Over Surfaces Treated With Inhibitors Used to Prevent Flash Rusting of Steel When Water or Water/Abrasive Blasted

SIGNIFICANCE AND USE
3.1 Water-blast cleaning with (SSPC-TR2/NACE 6G 198; SSPC-SP 5 (WAB)/NACE WAB-1; SSPC-SP 10 (WAB)/NACE WAB-2; SSPC-SP 6 (WAB)/NACE WAB-3; SSPC-SP 14 (WAB)/NACE WAB-8); SSPC-SP 7 (WAB)/NACE WAB-4 or without, (SSPC-SP WJ-1/NACE WJ-1; SSPC-SP WJ-2/NACE WJ-2; SSPC-SP WJ-3/NACE WJ-3; SSPC-SP WJ-4/NACE WJ-4) abrasive, results in flash rusting under some environmental conditions. Inhibitors are used to prevent flash rusting while drying and before coating application. The inhibitor or reaction products of the inhibitor on the substrate becomes part of the coating systems. Coating performance may be influenced by the inhibitor. Soluble contaminants or unreacted inhibitors left on the surface under the coating may cause premature failure. This practice includes a comparison of coating performance with and without inhibitors using various laboratory tests to simulate a range of conditions such as high moisture, marine atmospheric or water immersion.  
3.2 The user or specifier must determine the specific test methods to be used and exposure conditions. Some test methods referenced may not be applicable to all types of coatings.
SCOPE
1.1 This practice covers procedures to evaluate the compatibility of coatings with inhibitors used to prevent flash rusting of steel before application of coatings.  
1.2 The inhibitors are used with water-blast cleaning surface preparation and may be used with or without abrasives.  
1.3 The manufacturer of the coatings shall be consulted to ensure compatibility of inhibitors with the coatings.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D3911-16(2021)(Test Method)
Standard Test Method for Evaluating Coatings Used in Light-Water Nuclear Power Plants at Simulated Design Basis Accident (DBA) Conditions

SIGNIFICANCE AND USE
4.1 This test method is designed to provide a uniform test to determine the suitability of Coating Service Level 1 coatings used inside primary containment of light-water nuclear facilities under simulated DBA conditions. This test method is intended only to demonstrate that under DBA conditions, the coatings will remain intact and not form debris which could unacceptably compromise the operability of engineered safety systems. Deviations in actual surface preparation and in application and curing of the coating materials from qualification test parameters require an engineering evaluation to determine if additional testing is required.  
4.2 Since different plants have different tolerance levels for coating conditions, the definition of appropriate acceptance criteria is to be developed by the license holder based on individual plant engineered safety systems operability considerations.  
4.3 Use of this standard is predicated on the testing facility having a quality assurance program acceptable to the licensee.
SCOPE
1.1 This test method establishes procedures for evaluating protective coating systems test specimens under simulated DBA conditions. Included are a description of conditions and apparatus for temperature-pressure testing, and requirements for preparing, irradiating, testing, examining, evaluating, and documenting the samples.  
1.2 Consideration should be given to testing using worst case conditions (for example, surface preparation, temperature and pressure profile, irradiation, spray chemistry, chemical resistance, etc.) in an effort to reduce the number of tests required by changing plant accident calculations, changes in coating selection, etc.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D8157-19(Guide)
Standard Guide for Qualification Testing of Coatings Used in Coating Service Level I in Nuclear Power Plants

SIGNIFICANCE AND USE
4.1 This guide presents concise guidance and approach to developing a test document for qualifying a coating for CSLI service, whether a new or existing coating. Guidance for evaluating existing qualification test data for applicability is presented in Guide D8104.  
4.2 The requirements for qualification testing can be found in Quality Assurance Criteria III (Design Control), IX (Control of Special Processes), and XI (Test Control) of 10 CFR 50, Appendix B, as implemented, respectively, by Requirements III, IX, and XI of NQA-1. A test document developed per this guide is intended to be compliant with these requirements.  
4.3 This guide implements the guidance provided in Guide D5144 for qualification of coatings for use in CSLI service. Additional guidance is provided in Regulatory Guide 1.54, Revisions 0 through 3, as may be invoked by the licensee.  
4.4 For plants with a license basis that predates the requirements of ANSI N5.12 and N101.2, this guide also is applicable. For these plants, the coatings or coating systems may be designated as acceptable, rather than qualified.  
4.5 All qualification testing shall comply with the licensee’s approved quality assurance program.
SCOPE
1.1 This guide provides an approach to identifying the need for and development of a test document to qualify coatings for Coating Service Level I (CSLI) service in nuclear power plants.  
1.2 It is the intent of this guide to provide a recommended basis for establishing a coatings qualification test document, not to mandate a singular basis for all test documents. Variations or simplifications of the process described in this guide may be appropriate for any given operating or new construction nuclear power plant depending on its licensing commitments.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
ASTM
ASTM D4086-18(2023)(Practice)
Standard Practice for Visual Evaluation of Metamerism

SIGNIFICANCE AND USE
4.1 Metameric color matches result from the use of different colorants (pigments, dyes, and the like) in achieving the same color match. Usually, the purchaser requires that the color match be nonmetameric; this practice permits this requirement to be quickly tested in both field and laboratory. Where nonmetameric matches are not possible or practicable, for cost or other reasons, some limitation of metamerism may be required. The procedures for estimating the magnitude of metamerism described in this practice provide methods for assessing the effectiveness of such limitation.
SCOPE
1.1 This practice describes visual methods for detecting metamerism and for estimating the magnitude of a metameric color difference.  
1.2 The practice is limited to the consideration of illuminant metamerism and observer metamerism. This practice does not cover gonioapparent samples.  
1.3 This practice does not provide for the computation of indices of metamerism based upon instrumental measurement of spectral characteristics.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D7190-10(2023)(Practice)
Standard Practice to Evaluate Leaching of Water-Soluble Materials from Latex Paint Films

SIGNIFICANCE AND USE
4.1 Surfactant staining is a common problem with exterior house paints, particularly when subjected to humid environments (such as morning dew) shortly after application.  
4.2 Interior paints used in humid areas such as kitchens and bathrooms may also experience surfactant staining.  
4.3 Leaching of water-soluble materials may be dependent on colorant dispersions that are mixed into tint base paints. Other paint components may also affect the leaching of water-soluble materials.
SCOPE
1.1 This practice covers the ability of a latex paint film to resist staining caused by the leaching of water-soluble materials when contacted with water shortly after application.  
1.2 Water staining is attributed to the leaching of surfactants or other water-soluble materials from a paint film.  
1.3 The values stated in SI units are to be regarded as standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM F2853-10(2023)(Test Method)
Standard Test Method for Determination of Lead in Paint Layers and Similar Coatings or in Substrates and Homogenous Materials by Energy Dispersive X-Ray Fluorescence Spectrometry Using Multiple Monochromatic Excitation Beams

SIGNIFICANCE AND USE
5.1 This test method may be used for quantitative determinations of Pb in painted and unpainted articles such as toys, children’s products, and other consumer products. Typical test time for quantification of Pb in homogenous samples is 1 to 3 min; and typical test time for quantification of Pb in paint is 4 to 8 min.
SCOPE
1.1 This test method uses energy dispersive X-ray fluorescence (EDXRF) spectrometry for detection and quantification of lead (Pb) in paint layers, similar coatings, or substrates and homogenous materials. The following material types were tested in the interlaboratory study for this standard test method: ABS plastic, polyethylene, polypropylene, PVC, glass, zinc alloy, wood, and fabric.  
1.2 This technique may also be commonly referred to as High Definition X-ray Fluorescence (HDXRF) or Multiple Monochromatic Beam EDXRF (MMB-EDXRF).  
1.3 This test method is applicable for the products and materials described in 1.1 for a Pb mass fraction range of 14 to 1200 mg/kg for uncoated samples and 30 to 450 mg/kg for coated samples, as specified in Table 1 and determined by an interlaboratory study using representative samples  
1.4 Ensure that the analysis area of the sample is visually uniform in appearance and at least as large as the X-ray excitation beam at the point of sample excitation.  
1.5 For coating analysis, this test method is limited to paint and similar coatings. Metallic coatings are not covered by this test method.  
1.6 X-ray Nomenclature—This standard names X-ray lines using the IUPAC convention with the Siegbahn convention in parentheses.  
1.7 There are no known ISO equivalent methods to this standard.  
1.8 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4214-23(Test Method)
Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint Films

SIGNIFICANCE AND USE
4.1 The procedures provide a broad range of techniques and photographic references to evaluate chalking of exterior paints.
SCOPE
1.1 These test methods cover the evaluation of the degree of chalking on white or tinted exterior paint films. These test methods describe the procedures recommended for transferring the chalk to a fabric or fingertip, which is then compared to photographic reference standards, or in the case of adhesive tapes, compared to a reflectance table or photographic reference standards, to determine the degree of chalking.  
1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D4147-18(2023)(Practice)
Standard Practice for Applying Coil Coatings Using Wire-Wound Drawdown Bars

SIGNIFICANCE AND USE
3.1 This practice is useful in the laboratory to simulate roll-coated films.
SCOPE
1.1 This practice covers a procedure for applying a coil coating film of uniform thickness on a flat metal panel using wire-wound drawdown bars.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off