iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM B494/B494M-08(2020)

(Specification)

Standard Specification for Primary Zirconium

Standard Specification for Primary Zirconium

ABSTRACT
This specification covers two grades (Grade R60702 and Grade R60703) of zirconium metal commonly designated as sponge or chunklets, but may also take other forms. This specification does not include crystal bar zirconium. This sponge is used in non-nuclear applications. Zirconium metal is usually prepared by reduction of zirconium tetrachloride, and it gets its physical characteristics from the processes involved in production. These characteristics may be expected to vary greatly with manufacturing methods. This specification, however, is not limited to metal prepared by reduction of tetrachloride or to material of any specific physical form. Only virgin zirconium metal, in identified, uniform, well-mixed blends, shall be supplied under this specification. The material shall conform to the chemical composition requirements for zirconium, hafnium, iron, chromium, hydrogen, nitrogen, carbon, and oxygen. The material shall be subjected to a number of chemical tests as required in this specification.
SCOPE
1.1 This specification covers two grades of zirconium metal commonly designated as sponge or chunklets, but may also take other forms. This specification does not include crystal bar zirconium. This sponge is used in non-nuclear applications.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 The following precautionary caveat pertains only to the test method portions of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
31-Mar-2020
ICS
77.120.99 - Other non-ferrous metals and their alloys
Technical Committee
B10 - Reactive and Refractory Metals and Alloys
Drafting Committee
B10.02 - Zirconium and Hafnium
Current Stage
Ref Project

Relations

Replaces
ASTM B494/B494M-08(2014) - Standard Specification for Primary Zirconium
Effective Date
01-Apr-2020
Refers
ASTM E29-08 - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
01-Oct-2008
Refers
ASTM E29-06b - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
15-Nov-2006
Refers
ASTM E29-06a - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
15-Sep-2006
Refers
ASTM E29-06 - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
01-May-2006
Refers
ASTM E29-04 - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
01-Dec-2004
Refers
ASTM E29-02e1 - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
10-May-2002
Refers
ASTM E29-93a(1999) - Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
Effective Date
10-May-1999

Buy Standard

ASTM B494/B494M-08(2020) - Standard Specification for Primary ZirconiumASTM B494/B494M-08(2020) - Standard Specification for Primary Zirconium
PreviousNext
Technical specification
ASTM B494/B494M-08(2020) - Standard Specification for Primary Zirconium
English language
3 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:B494/B494M −08 (Reapproved 2020)
Standard Specification for
Primary Zirconium
This standard is issued under the fixed designation B494/B494M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1.1 Discussion—The process is one where the metal
condenses to the solid state and does not melt.
1.1 This specification covers two grades of zirconium metal
3.1.2 chunklets, n—zirconium metal produced from the
commonly designated as sponge or chunklets, but may also
reduction of the chloride, usually by sodium.
takeotherforms.Thisspecificationdoesnotincludecrystalbar
3.1.2.1 Discussion—In this process, the reduced metal is
zirconium. This sponge is used in non-nuclear applications.
melted and dripped onto a rotating disk to form chunklets.
1.2 Unless a single unit is used, for example corrosion mass
3.2 Lot—alotshallconsistofasingleblendproducedatone
gain in mg/dm , the values stated in either inch-pound or SI
time.
units are to be regarded separately as standard. The values
stated in each system are not exact equivalents; therefore each
system must be used independently of the other. SI values 4. Classification
cannot be mixed with inch-pound values.
4.1 Primary zirconium is furnished in two grades:
1.3 The following precautionary caveat pertains only to the
4.1.1 Grade R60702—Unalloyed zirconium.
test method portions of this specification. This standard does 4.1.2 Grade R60703—Unalloyed zirconium for metallurgi-
not purport to address all of the safety concerns, if any,
cal alloying.
associated with its use. It is the responsibility of the user of this
standard to establish appropriate safety, health, and environ-
5. Ordering Information
mental practices and determine the applicability of regulatory
5.1 Orders for material under this specification shall include
limitations prior to use.
the following information, when applicable:
1.4 This international standard was developed in accor-
5.1.1 Quantity (weight),
dance with internationally recognized principles on standard-
5.1.2 Name of material (zirconium sponge or chunklet),
ization established in the Decision on Principles for the
5.1.3 Grade number (see 4.1),
Development of International Standards, Guides and Recom-
5.1.4 ASTM designation and year of issue,
mendations issued by the World Trade Organization Technical
5.1.5 Check analysis (see 7.2),
Barriers to Trade (TBT) Committee.
5.1.6 Sampling of small blends (see 8.1.1),
5.1.7 Inspection (see 11.1),
2. Referenced Documents
5.1.8 Product marking (Section 15),
2.1 ASTM Standards:
5.1.9 Packaging (Section 16),
E29 Practice for Using Significant Digits in Test Data to
5.1.10 Oxygen limits, when needed (Table 1), and
Determine Conformance with Specifications
5.1.11 Additions to the specification as required.
3. Terminology
NOTE1—Atypicalorderingdescriptionisasfollows:3000lb[2000kg]
zirconium sponge, ASTM B494/B494M - 01, Grade R60703.
3.1 Forms:
3.1.1 sponge, n—zirconium metal produced from the reduc-
6. Materials and Manufacture
tion of the chloride, usually by magnesium.
6.1 Zirconium metal is usually prepared by reduction of
zirconium tetrachloride, and it gets its physical characteristics
This specification is under the jurisdiction of ASTM Committee B10 on
from the processes involved in production. These characteris-
Reactive and Refractory Metals and Alloys and is the direct responsibility of
Subcommittee B10.02 on Zirconium and Hafnium.
tics may be expected to vary greatly with manufacturing
Current edition approved April 1, 2020. Published April 2020. Originally
methods. This specification, however, is not limited to metal
approved in 1969. Last previous edition approved in 2014 as B494/B494M – 08
prepared by reduction of tetrachloride or to material of any
(2014). DOI: 10.1520/B0494_B0494M-08R20.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or specific physical form.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.2 Only virgin zirconium metal, in identified, uniform,
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. well-mixed blends, shall be supplied under this specification.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
B494/B494M−08 (2020)
TABLE 1 Chemical Requirements
9.1.2 At least one sample shall be analyzed fro magnesium
Composition, % or sodium and chloride.
Element
Grade R60702 Grade R60703
9.2 Retests:
Zirconium + hafnium 99.2 min 98.0 min
9.2.1 If any sample or specimen exhibits obvious surface
Hafnium 4.5 max 4.5 max
contamination or improper preparation disqualifying it as a
Iron + chromium 0.2 max .
Hydrogen 0.005 max .
truly representative sample, it shall be discarded and a new
Nitrogen 0.025 max .
sample or specimen substituted.
Carbon 0.05 max .
AA
9.2.2 If the results of any tests of any lot do not conform to
Oxygen
A the requirements specified, retests shall be made on additional
Limits as specified by the purchaser.
samples of double the original number from the same lot. Each
of the retest values shall conform to the requirements specified.
7. Chemical Composition
10. Specimen Preparation
7.1 The material shall conform to the requirements as to
10.1 The sample for chemical analysis of impurities other
chemical composition prescribed in Table 1.
than magnesium or sodium and chloride shall be obtained in
7.2 The purchaser may perform a check analysis for any
accordance with 8.1.2 and shall be compacted into consumable
elements listed in Table 1. The sampling and testing require-
electrodes,thenmeltedtoingotforminanarcfurnaceofatype
ments shall be as agreed upon between the purchaser and
conventionally used for reactive metals. The ingot shall be
su
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM B349/B349M-16(2021)(Specification)
Standard Specification for Zirconium Sponge and Other Forms of Virgin Metal for Nuclear Application

ABSTRACT
This specification covers one grade of virgin zirconium metal commonly designated as sponge because of its porous, sponge-like texture, but it may also take other forms such as chunklets. The one grade described is designated as Reactor Grade R60001, suitable for use in nuclear applications. The main characteristic of the reactor grade is its low nuclear cross section as achieved by removal of hafnium. Zirconium metal is usually prepared by reduction of zirconium tetrachloride, and gets its physical characteristics from the processes involved in production. These characteristics may be expected to vary greatly with manufacturing methods. Only virgin zirconium metal, in identified, uniform, well-mixed blends, shall be used. The zirconium metal shall conform to the requirements for chemical composition specified.
SCOPE
1.1 This specification covers one grade of virgin zirconium metal commonly designated as sponge because of its porous, sponge-like texture, but it may also take other forms such as chunklets, suitable for use in nuclear applications.  
1.2 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM B777-15(2020)(Specification)
Standard Specification for Tungsten Base, High-Density Metal

ABSTRACT
This specification establishes the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with other materials for protection against corrosion and abrasion; intended for uses such as weights or counter-balances in static or dynamic balancing, high-speed rotating inertia members, radiation shielding, hypervelocity impact, and vibration-damping applications. The chemical; physical properties, such as microstructure and machinability; mechanical properties, such as tensile strength, yield strength, elongation, and hardness; and composition requirements, such as density; are detailed.
SCOPE
1.1 This specification covers the requirements for four classes of machinable, high-density tungsten base metal produced by consolidating metal powder mixtures, the composition of which is mainly tungsten. This material specification may be used for bare parts or for parts that may be coated with other materials for protection against corrosion and abrasion.  
1.2 This specification describes physical, mechanical, and microstructural testing of a material lot based on the use of test coupons, not actual parts. Sintered properties typically vary both with part size and sampling location within a given part. Results obtained from coupon testing may therefore differ from the properties of a specific location in a larger part.  
1.3 Intended Use—Parts made from this material are intended for uses such as weights or counter-balances in static or dynamic balancing, high-speed rotating inertia members, radiation shielding, hypervelocity impact, and vibration-damping applications. In selecting the appropriate alloy for a given application, it is important to note that as the tungsten content of the alloy is increased, stiffness, radiation attenuation, and density increase with an accompanying decrease in attainable ductility.  
1.4 Special Applications—For particular applications, properties or requirements other than those specified in Sections 5, 6, and 7 of this specification may be important. These alloys may contain elements which make them weakly ferromagnetic. Where freedom from magnetic response is required, this should be specified in the purchase order. Class 4 is not available in a non-magnetic grade. For purposes of this specification, non-magnetic material is defined as material having a maximum magnetic permeability of 1.05 (see Test Method A342). Also for special applications involving large sections, methods for determining internal quality, such as mechanical testing of specimens excised from these larger sections or suitable nondestructive tests may be applied. If such part property data are required, an additional part-specific test program shall be specified in the purchase order.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM G2/G2M-19(Test Method)
Standard Test Method for Corrosion Testing of Products of Zirconium, Hafnium, and Their Alloys in Water at 680°F (360°C) or in Steam at 750°F (400°C)

SIGNIFICANCE AND USE
5.1 This test method is primarily used as an acceptance test for products of zirconium, hafnium, and their alloys. This standard has been widely used in the development of new alloys, heat treating practices, and for evaluation of welding techniques.  
5.2 Specimens are normally tested after careful etching and rinsing. Specimens with as-manufactured surfaces may also be tested without further surface removal.  
5.3 When tubing with a second material clad on the inner surface is to be tested, the inner cladding shall be removed prior to the test.
SCOPE
1.1 This test method covers (1) the determination of mass gain, and (2) the surface inspection of products of zirconium, hafnium, and their alloys when corrosion tested in water at 680°F [360°C] or in steam at 750°F [400°C].  
1.2 This test method is to be utilized in its entirety to the extent specified herein as a product acceptance test.  
1.3 This test method may be used on wrought products, castings, powder metallurgy products, and weld metals.  
1.4 Unless a single unit is used, for example corrosion mass gain in mg/dm2, the values stated in either inch-pound or SI units are to be regarded separately as standard. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. SI values cannot be mixed with inch-pound values.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see Section 9.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM B277-18(2024)(Test Method)
Standard Test Method for Hardness of Electrical Contact Materials

SIGNIFICANCE AND USE
3.1 The Rockwell hardness and Rockwell superficial tests are useful when the test specimens are sufficiently thick (in relation to the indentor load) to ensure that the results are not affected by the flow of metal on the surface of the anvil. On a solid piece the flow of metal on the under surface may be detected by a bulge or marking. On composite pieces where the contact materials are attached to backings of a different material, the thickness limitations imposed for a solid piece shall apply to the contact material portion of such composite pieces.
Note 1: As a matter of information, it may be stated that tests on fine silver showed that on annealed samples having a Rockwell 15T hardness of 27, the readings were not affected on thicknesses 1/16 in. (1.6 mm) or over. On thicknesses of 1/32 in. (0.8 mm) Rockwell 15T scale readings of 72 and higher were not affected.  
3.2 The microindentation hardness test is of questionable significance when the metallic phases in a material are so large that the indentation does not represent an accurate average hardness. Sintered contact materials usually contain segregates differing greatly in hardness from the matrix hardness and may destroy the validity of microindentation hardness readings.  
3.3 Other aspects of significance and use shall be as described in the particular ASTM test method used, as listed in Section 2.
SCOPE
1.1 This test method covers the determination of the hardness of metallic materials used for electrical contacts. Rockwell, Rockwell superficial, Brinell, and microindentation hardness tests are included, along with information on the limitations and use of these tests.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar will all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    2 pages
    English language
    sale 15% off
ASTM
ASTM B541-24(Specification)
Standard Specification for Gold Electrical Contact Alloy

ABSTRACT
This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts. The material shall be finished by cold working, annealing, turning, grinding, and age hardening. The materials shall conform to the specified chemical composition requirements. Tensile strength, elongation, and hardness shall be determined by tension and hardness tests. Chemical analysis shall be done by spectrochemical or wet analysis methods.
SCOPE
1.1 This specification covers a gold-rich, age-hardenable alloy in rod, wire, and strip form applicable to electrical contacts.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary statement pertains to the test method portion only, Section 8, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM E439-23(Test Method)
Standard Test Methods for Chemical Analysis of Beryllium

SIGNIFICANCE AND USE
4.1 These test methods for the chemical analysis of beryllium metal are primarily intended as referee methods to test such materials for compliance with compositional specifications. It is assumed that all who use these test methods will be trained analysts capable of performing common laboratory procedures skillfully and safely. It is expected that work will be performed in a properly equipped laboratory.
SCOPE
1.1 These test methods cover the chemical analysis of beryllium having chemical compositions within the following limits:    
Element  
Range, %  
Aluminum  
0.05 to 0.30  
Beryllium  
97.5 to 100    
Beryllium Oxide  
0.3 to 3    
Carbon  
0.05 to 0.30  
Copper  
0.005 to 0.10  
Chromium  
0.005 to 0.10  
Iron  
0.05 to 0.30  
Magnesium  
0.02 to 0.15  
Nickel  
0.005 to 0.10  
Silicon  
0.02 to 0.15  
1.2 The test methods in this standard are contained in the sections as follows.    
Sections  
Chromium by the Diphenylcarbazide Spectrophotometric Test Method
[0.004 % to 0.04 %]  
10 – 19  
Iron by the 1,10-Phenanthroline Spectrophotometric Test Method
[0.05 % to 0.25 %]  
20 – 29  
Manganese by the Periodate Spectrophotometric Test Method
[0.008 % to 0.04 %]  
30 – 39  
Nickel by the Dimethylglyoxime Spectrophotometric Test Method
[0.001 % to 0.04 %]  
40 – 49  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    8 pages
    English language
    sale 15% off
  • Standard
    8 pages
    English language
    sale 15% off
ASTM
ASTM E3097-23(Test Method)
Standard Test Method for Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys

SIGNIFICANCE AND USE
5.1 Constant force thermal cycling tests determine the effect of stress on the transformation temperatures, recovered strain and residual strain of a shape memory alloy. The tests may be for one thermal cycle. A standard test method for force controlled repeated thermal cycling of shape memory alloys is currently under development.  
5.2 Measurement of the specimen's thermomechanical behavior closely parallels many shape memory applications and provides a result that is applicable to the function of the material.  
5.3 This test method may be used for, but is not limited to, wire, round tube, or strip samples. Thus it is able to provide an assessment of the product in its semi-finished form.  
5.4 This test method provides a simple method for determining transformation temperatures by heating and cooling specimens through their full thermal transformation under force.  
5.5 This test method can be used on trained and processed material in a semi-finished form to measure Two Way Shape Memory Effect by comparing the strain in the austenite state and martensite states with no minimal applied stress. The force is set to a minimum value not to exceed a corresponding stress of 7 MPa (in accordance Test Method F2516).  
5.6 This test method is useful for quality control, specification acceptance, and research.  
5.7 Transformation temperatures derived from this test method may not agree with those obtained by other test methods due to the effects of strain and stress on the transformation.  
5.8 Components such as springs or other semi-finished parts can be tested using this method as agreed upon by the customer and supplier. Units of stress and strain can be replaced with force and displacement.
SCOPE
1.1 This test method defines procedures for thermomechanical cycling of shape memory alloy (SMA) material and components under constant force. This method characterizes the transformation properties such as transformation temperatures, actuation strain and residual strain, when a SMA is thermally cycled through the phase transformation under a constant applied force. This test is done to provide data for the selection of SMA materials, quality control, design allowables and actuator design.  
1.2 Units—The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM B664-18(2023)(Specification)
Standard Specification for 80 % Silver-20 % Graphite Sliding Contact Material

ABSTRACT
This specification defines the criteria for composition and other requirements for sliding contact materials or brushes with a nominal composition by weight of 20% silver and 80% graphite. Materials shall adhere to specified requirements for chemical composition, density, shear strength, and microstructure. They shall also conform to typical values of Rockwell superficial hardness and specific resistance.
SCOPE
1.1 This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 80 %, by weight, with the balance being substantially graphite.  
1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar will all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B717-23(Specification)
Standard Specification for Refined Ruthenium

ABSTRACT
This specification covers refined ruthenium as sponge and powder in one grade as follows: Grade 99.80 and Grade 99.90. The material may be produced by any refining process that yields a product capable of meeting the chemical requirements of this specification. The material should conform to the requirements for chemical composition as prescribed.
SCOPE
1.1 This specification covers refined ruthenium as sponge and powder in one grade as follows:  
1.1.1 Grade 99.80—Ruthenium having a purity of 99.80 %.  
1.1.2 Grade 99.90—Ruthenium having a purity of 99.90 %.  
Note 1: For the purposes of determining conformance with this specification, an observed value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the limiting value in accordance with the rounding method of Practice E29.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM B692-18(2023)(Specification)
Standard Specification for 75 % Silver-25 % Graphite Sliding Contact Material

ABSTRACT
This specification defines the criteria for the chemical composition and other requirements (including physical properties, microstructure, superficial hardness, and specific resistance ) for silver-graphite brushes for sliding electrical contacts. The percentage of silver, graphite, ash in graphite, and total metal impurities are prescribed. The minimum acceptable values for the physical properties such as density, determined by measurement and weight method, and shear strength are given. Typical Rockwell hardness and specific resistance for the material are also specified.
SCOPE
1.1 This specification defines the criteria for composition and other requirements for brushes with a nominal silver content of 75 weight % with the balance being substantially graphite.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off