ASTM F1347-91(2012)
(Specification)Standard Specification for Manually Operated Fueling Hose Reels
Standard Specification for Manually Operated Fueling Hose Reels
ABSTRACT
This specification covers manually operated fueling hose reels for use with collapsible and noncollapsible hose. Fueling hose reels shall be of one of the following types as specified: type 1, type 2, type 3, and type 4. The hose reel shall be of a durable, rigid construction, as light in weight and compact as practicable. The reel drum may have either smoothly formed flat sides or suitable spoke ribs, so formed as not to damage the hose. Reels shall be provided with a holding brake to lock the reel in any position. The reel shall be fitted with a device for clamping the hose nozzle securely to the reel to prevent unwinding of the hose and damage to the nozzle. The reel hub discharge shall be angled to provide a smooth tangential contact of the hose with the reel drum. The reel shall have an aromatic fuels tight rotating joint between reel inlet connection and the rotating hub on the reel drum. The reel inlet connection shall be flanged, the flange being part of the rotating swivel joint. Hydrostatic tset and operating test shall be performed to meet the requirements prescribed.
SCOPE
1.1 This specification covers manually operated fueling hose reels for use with collapsible and noncollapsible hose.
1.2 The values stated in inch-pound units are to be regarded as standard. The SI units given in parentheses are for information only.
1.3 The following precautionary caveat pertains only to the test methods portion, Section 12 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:F1347 −91 (Reapproved 2012) An American National Standard
Standard Specification for
Manually Operated Fueling Hose Reels
This standard is issued under the fixed designation F1347; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope 2.3 Military Standard:
MIL-STD-130IdentificationMarkingofU.S.MilitaryProp-
1.1 This specification covers manually operated fueling
erty
hose reels for use with collapsible and noncollapsible hose.
1.2 The values stated in inch-pound units are to be regarded
3. Classification
as standard. The SI units given in parentheses are for informa-
3.1 Fueling hose reels shall be of one of the following types
tion only.
as specified:
1.3 The following precautionary caveat pertains only to the
3.1.1 Type 1—For 150 ft (46 m) of collapsible 2 ⁄2-in.
test methods portion, Section 12 of this specification: This
(65-mm) hose.
standard does not purport to address all of the safety concerns,
3.1.2 Type 2—For 150 ft (46 m) of noncollapsible 1 ⁄2-in.
if any, associated with its use. It is the responsibility of the user
(38-mm)hoseor100ft(30m)ofnoncollapsible2-in.(50-mm)
of this standard to establish appropriate safety and health
hose.
practices and determine the applicability of regulatory limita-
3.1.3 Type 3—For 150 ft (46 m) of noncollapsible 1 ⁄2-in.
tions prior to use.
(38-mm) hose or for 150 ft (46 m) of collapsible 2 ⁄2-in.
(65-mm) hose.
2. Referenced Documents
3.1.4 Type 4—Capacity as specified by purchaser.
2.1 ASTM Standards:
B148Specification for Aluminum-Bronze Sand Castings
4. Ordering Information
D3006 Specification for Polyethylene Plastic Pressure-
4.1 Ordersformaterialunderthisspecificationshallinclude
Sensitive Electrical Insulating Tape
the following information:
D3951Practice for Commercial Packaging
3 4.1.1 Title, number, and year of issue of this specification,
2.2 Military Specifications:
4.1.2 Type of hose reel including hose size and type (see
MIL-S-901 Shock Test, H.I. (High-Impact); Shipboard
3.1), (length of hose for Type 4),
Machinery, Equipment and Systems, Requirements for
4.1.3 Whetherright-orleft-handreelsarerequired(see6.5),
MIL-T-16366 Terminals, Electric Lug and Conductor
4.1.4 Flange inlet thickness and bolt hole dimensions (see
Splices, Crimp Style
6.7),
MIL-H-17902Hose, End Fittings and Hose Assemblies,
4.1.5 Drawings required (see 9.1),
Synthetic Rubber, Aircraft Fuels
4.1.6 Thenumberofsamplestobeinspectedandtested(see
MIL-F-20042Flanges, Pipe and Bulkhead, Bronze (Silver
11.2),
Brazing)
4.1.7 Certification, if required (see 15.1),
MIL-P-24441Epoxy-Polyamide Primer
4.1.8 Test report, if required (see 15.1), and
4.1.9 Applicability of supplementary requirements.
This specification is under the jurisdiction ofASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.07 on
5. Materials and Manufacture
General Requirements.
Current edition approved May 1, 2012. Published May 2012. Originally
5.1 Exceptasotherwisespecifiedherein,thehosereelsshall
approved in 1991. Last previous edition approved in 2006 as F1347–91 (2006).
be constructed of aluminum, aluminum bronze, or other
DOI: 10.1520/F1347-91R12.
suitable nonsparking materials.All fittings conveying aromatic
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
fuels through the hose reel shall be made of aluminum bronze
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
in accordance with Specification B148, copper alloy UNS No.
the ASTM website.
C95300.Topreventdeteriorationinseaatmosphere,aluminum
Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,
parts should not contact brass or bronze; however, where such
Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://
dodssp.daps.dla.mil. aluminum parts come in contact with brass or bronze, they
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
F1347−91 (2012)
shall be protected by adhesive-backed insulating tape, Speci- 6.2 Reel Drum—The reel drum may have either smoothly
fication D3006. All aluminum parts shall be given a coat of formed flat sides or suitable spoke ribs, so formed as not to
epoxy-polyamide primer. damage the hose. The rims of the drum shall provide a good
grip for hand rewind.
6. Construction
6.3 Holding Brake—Reels shall be provided with a holding
6.1 Reel and Drum Assembly—The hose reel shall be of a brake to lock the reel in any position.
durable, rigid construction, as light in weight and compact as
6.4 Nozzle Clamp—The reel shall be fitted with a device for
practicable. The drum assembly (drum, reel sides, and its
clamping the hose nozzle securely to the reel to prevent
reinforcements)shallwithstandthehosepullwithoutdistortion
unwinding of the hose and damage to the nozzle.
orcollapseandshallbecapableofwithstandingsomesideways
hose pull without undue distortions. The construction of the 6.5 Reel Hub Discharge—The reel hub discharge shall be
completed drum assembly shall be such that disassembly can angled to provide a smooth tangential contact of the hose with
be readily accomplished with standard tools. When bolted the reel drum as shown on Fig. 1 and Fig. 2, so that the hose
down to a true flat surface, the shaft and rotating seal will not kink at the discharge connection. The hub discharge
centerlines shall be in true alignment and the drum assembly fitting and adapter shall be in accordance with Fig. 2 and Fig.
shall turn without binding under a rim pull not to exceed 7 lb 3 for Types 1, 2, and 3, respectively. Reels shall be right- or
(198 kg) with the reel unpressurized. Both ends of the drum left-hand operation and top or bottom wind, as specified. A
shaft shall be supported on ball or roller bearings that shall right-hand, top-wind reel is defined as one that, when looking
have provision for easy lubrication. Reels shall be designed so intotheflangedadapteronthedischargefittingwhenitisatthe
that all bearings, and other corrodible parts, are adequately top of the drum, has its inlet connection on the right-hand side.
protected from the weather. Provision shall be made for (Note that a top-wind, right-hand reel and a bottom-wind,
lubrication of working parts such as bearings or other mating left-hand reel are identical.) It shall be possible by turning the
surfaces, and all such parts shall be lubricated before delivery discharge fitting around, or by other simple means, to enable
with a lubricant soluble in aromatic fuels. Bearing seals shall the hose to unreel from the bottom of the reel drum to either
be such that the pressure caused by forced lubrication will not sideofthereel(thatis,tomakethereeleitherrighthandorleft
bind the shaft. hand) without rotating the reel drum.
FIG. 1 Hose Reel Dimensions
F1347−91 (2012)
FIG. 2 Discharge Fitting and Adapter Details for Type 1 and 3, 2 ⁄2-in. (65-mm) Collapsible Reels
6.6 Aromatic Fuels Tight Rotating Joint—The reel shall reel (that is, from inlet flange to flanged adapter) shall be
have an aromatic fuels tight rotating joint between reel inlet
capable of being removed as a unit without disassembly of the
connection and the rotating hub on the reel drum. The rotating drum or reel sides.
jointshallnotbindunderloading(shallbesupportedtoprevent
7.2 Reel Hose Capacity—Reels shall be capable of contain-
a bending load being applied), shall have provision for lubri-
ing lengths of hose, as required, for Types 1, 2, 3, or 4. The
cation of moving parts, and shall be capable of easy disassem-
hose used shall be either collapsible or noncollapsible as
bly for maintenance purposes. The rotating joint shall be tight
specified.
under the pressure specified in 7.1.
6.7 Inlet Connection—The reel inlet connection shall be 7.3 Temperature—The reels and the lubricant used shall be
flanged, the flange being part of the rotating swivel joint. The capable of satisfactory operation within the range of tempera-
flange thickness and bolt hole drilling shall be as specified in tures from −20 to +120°F (−29 to +49°C).
the contract or purchase order.
8. Dimensions, Mass, and Permissible Variations
7. Performance Requirements
8.1 The drum diameter shall not be less than the minimum
7.1 Fluid Handling—Reels shall be capable of passing 300
bending diameter of the hose. The general outline and base
gal/min (0.0189 m /s) of aviation fuel at a pressure of 150 psi
mounting dimensions and mass shall be in accordance with
(1.03MPa)andshallwithstandastaticfuelpressureof225psi
Fig. 1.
(1.55 MPa) without leakage or other signs of weakness.
Restrictions and turbulence through the re
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.