ASTM D4142-89(2001)
(Guide)Standard Guide for Testing Epoxy Resins
Standard Guide for Testing Epoxy Resins
SIGNIFICANCE AND USE
This guide directs the user to test methods that determine properties generally accepted as standard test items for classification of epoxy resins.
SCOPE
1.1 This guide covers methods for testing epoxy resins as listed in Table 1. All of the methods were tested by interlaboratory participation in accordance with usual ASTM guidelines. Each method specifies a recommended amount of sample for starting a separate analysis, but several of the procedures can be conducted on the same starting material if so desired. For example, viscosity, color, and density could be run on the same specimen.
1.2 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
Designation:D4142–89 (Reapproved2001)
Standard Guide for
Testing Epoxy Resins
This standard is issued under the fixed designation D4142; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
TABLE 1 Methods for Testing Epoxy Resins
1. Scope
Test Method Section ASTM Designation
1.1 This guide covers methods for testing epoxy resins as
Epoxy content 4 D1652
listed in Table 1. All of the methods were tested by interlabo-
Hydrolyzable chlorine 5 D1726
ratory participation in accordance with usual ASTM guide-
Total chlorine 6 D1847
lines.Eachmethodspecifiesarecommendedamountofsample
Viscosity 7 D445, D1545D1545
Color 8 D1544, D1209D1209
for starting a separate analysis, but several of the procedures
Density 9 D1475
can be conducted on the same starting material if so desired.
Nonvolatile content 10 D1259
For example, viscosity, color, and density could be run on the
Acid value 11 D1639
same specimen.
1.2 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
D1726 Test Methods for Hydrolyzable Chloride Content of
responsibility of the user of this standard to establish appro-
Liquid Epoxy Resins
priate safety and health practices and determine the applica-
D1847 Test Methods for Total Chlorine Content of Epoxy
bility of regulatory limitations prior to use.
Resins
2. Referenced Documents
3. Significance and Use
2.1 ASTM Standards:
3.1 This guide directs the user to test methods that deter-
D445 Test Method for Kinematic Viscosity of Transparent
mine properties generally accepted as standard test items for
and Opaque Liquids (and Calculation of Dynamic Viscos-
classification of epoxy resins.
ity)
D1209 Test Method for Color of Clear Liquids (Platinum-
4. Epoxy Content
Cobalt Scale)
4.1 The epoxy content of epoxy resins is determined by
D1259 Test Methods for Nonvolatile Content of Resin
reacting a solution of the resin with a standard solution of
Solutions
hydrogen bromide in glacial acetic acid. The quantity of acid
D1475 Test Method For Density of Liquid Coatings, Inks,
consumed is a measure of the epoxy content. Test Methods
and Related Products
D1652 was found to have a repeatability of 2 % of the epoxy
D1544 Test Method for Color of Transparent Liquids
content and a reproducibility of 6 % of the epoxy content.
(Gardner Color Scale)
D1545 Test Method forViscosity ofTransparent Liquids by
5. Hydrolyzable Chlorine
Bubble Time Method
5.1 Test Method D1726 covers the determination of the
D1639 Test Method for Acid Value of Organic Coating
65 easily hydrolyzable chlorine content of liquid epoxy resins in
Materials
concentrations below 1 weight %. The specimen is refluxed
D1652 Test Method for Epoxy Content of Epoxy Resins
with a known amount of a standard alcoholic potassium
hydroxide solution. The amount of hydroxide consumed is
measured by titration and corresponds to the hydrolyzable
This guide is under the jurisdiction of ASTM Committee D01 on Paint and
chlorine content of the resin. By interlaboratory testing, the
Related Coatings, Materials, and Applications and is the direct responsibility of
Subcommittee D01.33 on Polymers and Resins.
repeatability was found to be 0.02 %, and the reproducibility
Current edition approved April 28, 1989. Published June 1989. Originally
was found to be 0.05 %, both absolute.
´1
published as D4142 – 82. Last previous edition D4142 – 82 . DOI: 10.1520/
D4142-89R01.
6. Total Chlorine
Annual Book of ASTM Standards, Vol 05.01.
Annual Book of ASTM Standards, Vol 06.04.
6.1 Organic and inorganic chlorine compounds are deter-
Annual Book of ASTM Standards, Vol 06.01.
minedinepoxyresinsinaccordancewithTestMethodsD1847.
Annual Book of ASTM Standards, Vol 06.03.
The resin specimen is oxidized by combustion in a bomb
Withdrawn. The last approved version of this historical standard is referenced
on www.astm.org. containing oxygen under pressure. The chlorides formed are
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
D4142–89 (2001)
dissolved
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.