ASTM A240/A240M-16
(Specification)Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
Standard Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
ABSTRACT
This specification covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications. The steel shall conform to the requirements as to chemical composition specified. The material shall conform to the mechanical properties specified.
SCOPE
1.1 This specification2 covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished in inch-pound units.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A240/A240M −16
Standard Specification for
Chromium and Chromium-Nickel Stainless Steel Plate,
Sheet, and Strip for Pressure Vessels and for General
1
Applications
This standard is issued under the fixed designationA240/A240M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* Flat-Rolled Stainless and Heat-Resisting Steel Plate,
2 Sheet, and Strip
1.1 This specification covers chromium, chromium-nickel,
A923 Test Methods for Detecting Detrimental Intermetallic
and chromium-manganese-nickel stainless steel plate, sheet,
Phase in Duplex Austenitic/Ferritic Stainless Steels
and strip for pressure vessels and for general applications
E112 Test Methods for Determining Average Grain Size
including architectural, building, construction, and aesthetic
E140 Hardness Conversion Tables for Metals Relationship
applications.
Among Brinell Hardness, Vickers Hardness, Rockwell
1.2 The values stated in either SI units or inch-pound units
Hardness, Superficial Hardness, Knoop Hardness, Sclero-
are to be regarded separately as standard. The values stated in
scope Hardness, and Leeb Hardness
each system may not be exact equivalents; therefore, each
E527 Practice for Numbering Metals and Alloys in the
system shall be used independently of the other. Combining
Unified Numbering System (UNS)
values from the two systems may result in non-conformance
4
2.2 SAE Standard:
with the standard.
J 1086 Practice for Numbering Metals and Alloys (UNS)
1.3 This specification is expressed in both inch-pound and
SI units. However, unless the order specifies the applicable
3. General Requirements
“M” specification designation (SI units), the material shall be
3.1 The following requirements for orders for material
furnished in inch-pound units.
furnished under this specification shall conform to the appli-
1.4 This standard does not purport to address all of the
cable requirements of the current edition of Specification
safety concerns, if any, associated with its use. It is the
A480/A480M.
responsibility of the user of this standard to establish appro-
3.1.1 Definitions;
priate safety and health practices and determine the applica-
3.1.2 General requirements for delivery;
bility of regulatory limitations prior to use.
3.1.3 Ordering information;
3.1.4 Process;
2. Referenced Documents
3.1.5 Special tests;
3
2.1 ASTM Standards:
3.1.6 Heat treatment;
A370 Test Methods and Definitions for Mechanical Testing
3.1.7 Dimensions and permissible variations;
of Steel Products
3.1.8 Workmanship, finish and appearance;
A480/A480M Specification for General Requirements for
3.1.9 Number of tests/test methods;
3.1.10 Specimen preparation;
3.1.11 Retreatment;
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
3.1.12 Inspection;
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
3.1.13 Rejection and rehearing;
A01.17 on Flat-Rolled and Wrought Stainless Steel.
Current edition approved May 1, 2016. Published May 2016. Originally
3.1.14 Material test report;
approved in 1940. Last previous edition approved in 2015 as A240/A240M – 15b.
3.1.15 Certification; and
DOI: 10.1520/A0240_A0240M-16.
3.1.16 Packaging, marking, and loading.
2
For ASME Boiler and Pressure Vessel Code applications see related Specifi-
cation SA-240 in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
4
Standards volume information, refer to the standard’s Document Summary page on Available from Society of Automotive Engineers (SAE), 400 Commonwealth
the ASTM website. Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A240/A240M−16
4. Chemical Composition 6.2 Supplementary Requirement S2 shall be invoked when
non-H grade austenitic stainless steels are ordered for ASME
4.1 The steel shall conform to the requirements as to
Code applications for service above 1000°F [540°C].
chemical composition specified inTable 1and shall conformto
applicable requirements specified in Specification A480/
6.3 Grade S31060, unless otherwise specified in the pur-
A480M.
chase order, shall conform to an average grain size of ASTM
No. 7 or coarser, as measured by Test Methods E112.
5. Mechanical Properti
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A240/A240M − 15b A240/A240M − 16
Standard Specification for
Chromium and Chromium-Nickel Stainless Steel Plate,
Sheet, and Strip for Pressure Vessels and for General
1
Applications
This standard is issued under the fixed designation A240/A240M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
2
1.1 This specification covers chromium, chromium-nickel, and chromium-manganese-nickel stainless steel plate, sheet, and
strip for pressure vessels and for general applications including architectural, building, construction, and aesthetic applications.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.3 This specification is expressed in both inch-pound and SI units. However, unless the order specifies the applicable “M”
specification designation (SI units), the material shall be furnished in inch-pound units.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
2. Referenced Documents
3
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
A923 Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels
E112 Test Methods for Determining Average Grain Size
E140 Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness,
Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
4
2.2 SAE Standard:
J 1086 Practice for Numbering Metals and Alloys (UNS)
3. General Requirements
3.1 The following requirements for orders for material furnished under this specification shall conform to the applicable
requirements of the current edition of Specification A480/A480M.
3.1.1 Definitions;
3.1.2 General requirements for delivery;
3.1.3 Ordering information;
3.1.4 Process;
3.1.5 Special tests;
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.17
on Flat-Rolled and Wrought Stainless Steel.
Current edition approved Nov. 1, 2015May 1, 2016. Published December 2015May 2016. Originally approved in 1940. Last previous edition approved in 2015 as
A240/A240M – 15a.A240/A240M – 15b. DOI: 10.1520/A0240_A0240M-15B.10.1520/A0240_A0240M-16.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-240 in Section II of that Code.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A240/A240M − 16
3.1.6 Heat treatment;
3.1.7 Dimensions and permissible variations;
3.1.8 Workmanship, finish and appearance;
3.1.9 Number of tests/test methods;
3.1.10 Specimen preparation;
3.1.11 Retreatment;
3.1.12 Inspection;
3.1.13 Rejection and rehearing;
3.1.14 Material test report;
3.1.15 Certification; and
3.1.16 Packaging, marking, and loading.
4. Chemical Composition
4.1 The steel shall conform to the requirements as to chemical composition specified in Table 1 and shall conform to applicable
requirements specified in Specification A480/A480M
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.