ASTM C1767M-21
(Specification)Standard Specification for Stainless Steel Jacketing for Insulation
Standard Specification for Stainless Steel Jacketing for Insulation
ABSTRACT
This specification applies to stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It provides physical requirements for stainless steel jacketing for thermal and acoustical insulation, but does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel). This specification also covers the classification of stainless steel jacketing, stainless steel jacketing materials and manufacture, required physical properties, workmanship, finish and appearance, sampling, inspection, certification, product marking, and packaging.
SCOPE
1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.
1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude use of Class E material which does not have a moisture barrier in this containment building application.
1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide C1423 provides guidance in selecting jacketing materials and their safe use.
1.4 This is a material specification and does not imply any performance of the installed system using the materials specified herein. For information about installation of stainless steel jacketing, see (1).2
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: A version of this specification in IP units is available as Specification C1767.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:C1767M −21
Standard Specification for
1
Stainless Steel Jacketing for Insulation
This standard is issued under the fixed designation C1767M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
1.1 This specification covers stainless steel jacketing for
mendations issued by the World Trade Organization Technical
thermal, acoustical, and fire protective insulation operating at
Barriers to Trade (TBT) Committee.
either above or below ambient temperatures and in both indoor
and outdoor locations. It does not cover insulation jacketing
2. Referenced Documents
made from other materials such as mastics, fiber reinforced
3
2.1 ASTM Standards:
plastic, PVC, aluminum, or coated carbon steel (for example,
A167 Specification for Stainless and Heat-Resisting
aluminum-zinc, galvanized steel, or aluminized steel) nor does
Chromium-Nickel Steel Plate, Sheet, and Strip (With-
it cover the details of thermal, acoustical, or fire protective
4
drawn 2014)
insulation systems.
A240/A240M Specification for Chromium and Chromium-
1.2 While not intended to cover use inside the containment
Nickel Stainless Steel Plate, Sheet, and Strip for Pressure
buildings of nuclear power plants, this standard does not
Vessels and for General Applications
preclude use of Class E material which does not have a
A480/A480M Specification for General Requirements for
moisture barrier in this containment building application.
Flat-Rolled Stainless and Heat-Resisting Steel Plate,
1.3 This specification provides physical requirements for Sheet, and Strip
stainless steel jacketing for thermal and acoustical insulation. B487 Test Method for Measurement of Metal and Oxide
Guide C1423 provides guidance in selecting jacketing materi- Coating Thickness by Microscopical Examination of
als and their safe use. Cross Section
C168 Terminology Relating to Thermal Insulation
1.4 This is a material specification and does not imply any
C450 Practice for Fabrication of Thermal Insulating Fitting
performance of the installed system using the materials speci-
Covers for NPS Piping, and Vessel Lagging
fied herein. For information about installation of stainless steel
2 C585 Practice for Inner and Outer Diameters of Thermal
jacketing, see (1).
Insulation for Nominal Sizes of Pipe and Tubing
1.5 The values stated in SI units are to be regarded as
C835 Test Method for Total Hemispherical Emittance of
standard. No other units of measurement are included in this
Surfaces up to 1400°C
standard.
C1371 Test Method for Determination of Emittance of
Materials Near Room Temperature Using Portable Emis-
NOTE 1—A version of this specification in IP units is available as
Specification C1767.
someters
C1423 Guide for Selecting Jacketing Materials for Thermal
1.6 This standard does not purport to address all of the
Insulation
safety concerns, if any, associated with its use. It is the
C1729M Specification for Aluminum Jacketing for Insula-
responsibility of the user of this standard to establish appro-
tion
priate safety, health, and environmental practices and deter-
C1767 Specification for Stainless Steel Jacketing for Insula-
mine the applicability of regulatory limitations prior to use.
tion
1.7 This international standard was developed in accor-
C1785 Test Method for Concentration of Pinhole Detections
dance with internationally recognized principles on standard-
in Moisture Barriers on Metal Jacketing
D3363 Test Method for Film Hardness by Pencil Test
1
This specification is under the jurisdiction of ASTM Committee C16 on
Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on
3
Insulation Systems. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved March 1, 2021. Published March 2021. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2014. Last previous edition approved in 2019 as C1767M – 19. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C1767M-21. the ASTM website.
2 4
The boldface numbers in parentheses refer to the list of references at the end of The last approved version of this historical standard is referenced on
this standard. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-29
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C1767M − 19 C1767M − 21
Standard Specification for
1
Stainless Steel Jacketing for Insulation
This standard is issued under the fixed designation C1767M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers stainless steel jacketing for thermal, acoustical, and fire protective insulation operating at either above
or below ambient temperatures and in both indoor and outdoor locations. It does not cover insulation jacketing made from other
materials such as mastics, fiber reinforced plastic, PVC, aluminum, or coated carbon steel (for example, aluminum-zinc, galvanized
steel, or aluminized steel) nor does it cover the details of thermal, acoustical, or fire protective insulation systems.
1.2 While not intended to cover use inside the containment buildings of nuclear power plants, this standard does not preclude use
of Class E material which does not have a moisture barrier in this containment building application.
1.3 This specification provides physical requirements for stainless steel jacketing for thermal and acoustical insulation. Guide
C1423 provides guidance in selecting jacketing materials and their safe use.
1.4 This is a material specification and does not imply any performance of the installed system using the materials specified herein.
2
For information about installation of stainless steel jacketing, see (1).
1.5 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
NOTE 1—A version of this specification in IP units is available as Specification C1767.
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1.7 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
4
A167 Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
1
This specification is under the jurisdiction of ASTM Committee C16 on Thermal Insulation and is the direct responsibility of Subcommittee C16.40 on Insulation
Systems.
Current edition approved Sept. 1, 2019March 1, 2021. Published September 2019March 2021. Originally approved in 2014. Last previous edition approved in 20162019
as C1767M – 16a.C1767M – 19. DOI: 10.1520/C1767M-19.10.1520/C1767M-21.
2
The boldface numbers in parentheses refer to the list of references at the end of this standard.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C1767M − 21
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and
for General Applications
A480/A480M Specification for General Requirements for Flat-Rolled Stainless and Heat-Resisting Steel Plate, Sheet, and Strip
B487 Test Method for Measurement of Metal and Oxide Coating Thickness by Microscopical Examination of Cross Section
C168 Terminology Relating to Thermal Insulation
C450 Practice for Fabrication of Thermal Insulating Fitting Covers for NPS Piping, and Vessel Lagging
C585 Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing
C835 Test Method for Total Hemispherical Emittance of Surfaces up to 1400°C
C1371 Test Method for Determination of Emittance of Materials Near Room Temperature Using Portable Emissometers
C1423 Guide for Selecting Jacketing Materials for Thermal Insulation
C1729M
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.