ASTM C31/C31M-18
(Practice)Standard Practice for Making and Curing Concrete Test Specimens in the Field
Standard Practice for Making and Curing Concrete Test Specimens in the Field
SIGNIFICANCE AND USE
4.1 This practice provides standardized requirements for making, curing, protecting, and transporting concrete test specimens under field conditions.
4.2 If the specimens are made and standard cured, as stipulated herein, the resulting strength test data when the specimens are tested are able to be used for the following purposes:
4.2.1 Acceptance testing for specified strength,
4.2.2 Checking adequacy of mixture proportions for strength, and
4.2.3 Quality control.
4.3 If the specimens are made and field cured, as stipulated herein, the resulting strength test data when the specimens are tested are able to be used for the following purposes:
4.3.1 Determination of whether a structure is capable of being put in service,
4.3.2 Comparison with test results of standard cured specimens or with test results from various in-place test methods,
4.3.3 Adequacy of curing and protection of concrete in the structure, or
4.3.4 Form or shoring removal time requirements.
SCOPE
1.1 This practice covers procedures for making and curing cylinder and beam specimens from representative samples of fresh concrete for a construction project.
1.2 The concrete used to make the molded specimens shall be sampled after all on-site adjustments have been made to the mixture proportions, including the addition of mix water and admixtures. This practice is not satisfactory for making specimens from concrete not having measurable slump or requiring other sizes or shapes of specimens.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to exposed skin and tissue upon prolonged exposure.2)
1.5 The text of this standard references notes which provide explanatory material. These notes shall not be considered as requirements of the standard.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C31/C31M − 18
Standard Practice for
1
Making and Curing Concrete Test Specimens in the Field
This standard is issued under the fixed designation C31/C31M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope* 2. Referenced Documents
3
1.1 This practice covers procedures for making and curing
2.1 ASTM Standards:
cylinder and beam specimens from representative samples of
C125 Terminology Relating to Concrete and Concrete Ag-
fresh concrete for a construction project.
gregates
C138/C138M Test Method for Density (Unit Weight),Yield,
1.2 The concrete used to make the molded specimens shall
be sampled after all on-site adjustments have been made to the and Air Content (Gravimetric) of Concrete
mixture proportions, including the addition of mix water and C143/C143M Test Method for Slump of Hydraulic-Cement
admixtures. This practice is not satisfactory for making speci- Concrete
mens from concrete not having measurable slump or requiring C172/C172M Practice for Sampling Freshly Mixed Con-
other sizes or shapes of specimens.
crete
C173/C173M Test Method forAir Content of Freshly Mixed
1.3 The values stated in either SI units or inch-pound units
Concrete by the Volumetric Method
are to be regarded separately as standard. The values stated in
C231/C231M Test Method forAir Content of Freshly Mixed
each system may not be exact equivalents; therefore, each
Concrete by the Pressure Method
system shall be used independently of the other. Combining
C330/C330M Specification for Lightweight Aggregates for
values from the two systems may result in non-conformance
Structural Concrete
with the standard.
C403/C403M Test Method for Time of Setting of Concrete
1.4 This standard does not purport to address all of the
Mixtures by Penetration Resistance
safety concerns, if any, associated with its use. It is the
C470/C470M Specification for Molds for Forming Concrete
responsibility of the user of this standard to establish appro-
Test Cylinders Vertically
priate safety, health, and environmental practices and deter-
C511 Specification for Mixing Rooms, Moist Cabinets,
mine the applicability of regulatory limitations prior to use.
Moist Rooms, and Water Storage Tanks Used in the
(Warning—Fresh hydraulic cementitious mixtures are caustic
Testing of Hydraulic Cements and Concretes
and may cause chemical burns to exposed skin and tissue upon
2
C617/C617M Practice for Capping Cylindrical Concrete
prolonged exposure. )
Specimens
1.5 The text of this standard references notes which provide
C1064/C1064M Test Method for Temperature of Freshly
explanatory material. These notes shall not be considered as
Mixed Hydraulic-Cement Concrete
requirements of the standard.
C1077 Practice forAgencies Testing Concrete and Concrete
1.6 This international standard was developed in accor-
Aggregates for Use in Construction and Criteria for
dance with internationally recognized principles on standard-
Testing Agency Evaluation
ization established in the Decision on Principles for the
C1758/C1758M Practice for Fabricating Test Specimens
Development of International Standards, Guides and Recom-
with Self-Consolidating Concrete
mendations issued by the World Trade Organization Technical
4
Barriers to Trade (TBT) Committee.
2.2 American Concrete Institute Publication:
309R Guide for Consolidation of Concrete
1
This practice is under the jurisdiction of ASTM Committee C09 on Concrete
and Concrete Aggregates and is the direct responsibility of Subcommittee C09.61
3
on Testing for Strength. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved Jan. 1, 2018. Published February 2018. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 1920. Last previous edition approved in 2017 as C31/C31M–17. DOI: Standards volume information, refer to the standard’s Document Summary page on
10.1520/C0031_C0031M-18. the ASTM website.
2 4
See Section on Safety Precautions, Manual ofAggregate and Concrete Testing, Available fromAmerican Concrete Institute (ACI), P.O. Box 9094, Farmington
Annual Book of ASTM Standards, Vol. 04.02. Hills, MI 48333-9094, http://www.aci-int.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C31/C31M − 18
TABLE 1 Tamping Rod Diameter Requirements
3. Terminology
Diamete
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C31/C31M − 17 C31/C31M − 18
Standard Practice for
1
Making and Curing Concrete Test Specimens in the Field
This standard is issued under the fixed designation C31/C31M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope*
1.1 This practice covers procedures for making and curing cylinder and beam specimens from representative samples of fresh
concrete for a construction project.
1.2 The concrete used to make the molded specimens shall be sampled after all on-site adjustments have been made to the
mixture proportions, including the addition of mix water and admixtures. This practice is not satisfactory for making specimens
from concrete not having measurable slump or requiring other sizes or shapes of specimens.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each
system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the
two systems may result in non-conformance with the standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use. (Warning—Fresh hydraulic cementitious mixtures are caustic and may cause
2
chemical burns to exposed skin and tissue upon prolonged exposure. )
1.5 The text of this standard references notes which provide explanatory material. These notes shall not be considered as
requirements of the standard.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
C125 Terminology Relating to Concrete and Concrete Aggregates
C138/C138M Test Method for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete
C143/C143M Test Method for Slump of Hydraulic-Cement Concrete
C172/C172M Practice for Sampling Freshly Mixed Concrete
C173/C173M Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method
C231/C231M Test Method for Air Content of Freshly Mixed Concrete by the Pressure Method
C330/C330M Specification for Lightweight Aggregates for Structural Concrete
C403/C403M Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance
C470/C470M Specification for Molds for Forming Concrete Test Cylinders Vertically
C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic
Cements and Concretes
C617/C617M Practice for Capping Cylindrical Concrete Specimens
C1064/C1064M Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete
1
This practice is under the jurisdiction of ASTM Committee C09 on Concrete and Concrete Aggregates and is the direct responsibility of Subcommittee C09.61 on Testing
for Strength.
Current edition approved June 15, 2017Jan. 1, 2018. Published July 2017February 2018. Originally approved in 1920. Last previous edition approved in 20152017 as
ɛ1
C31/C31M–15a–17. . DOI: 10.1520/C0031_C0031M-17.10.1520/C0031_C0031M-18.
2
See Section on Safety Precautions, Manual of Aggregate and Concrete Testing, Annual Book of ASTM Standards, Vol. 04.02.
3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C31/C31M − 18
C1077 Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency
Evaluation
C1758/C
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.