ASTM D2887-19ae2
(Test Method)Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography
Standard Test Method for Boiling Range Distribution of Petroleum Fractions by Gas Chromatography
SIGNIFICANCE AND USE
5.1 The boiling range distribution of petroleum fractions provides an insight into the composition of feedstocks and products related to petroleum refining processes. The gas chromatographic simulation of this determination can be used to replace conventional distillation methods for control of refining operations. This test method can be used for product specification testing with the mutual agreement of interested parties.
5.2 Boiling range distributions obtained by this test method are essentially equivalent to those obtained by true boiling point (TBP) distillation (see Test Method D2892). They are not equivalent to results from low efficiency distillations such as those obtained with Test Method D86 or D1160.
5.3 Procedure B was tested with biodiesel mixtures and reports the Boiling Point Distribution of FAME esters of vegetable and animal origin mixed with ultra low sulfur diesel.
SCOPE
1.1 This test method covers the determination of the boiling range distribution of petroleum products. The test method is applicable to petroleum products and fractions having a final boiling point of 538 °C (1000 °F) or lower at atmospheric pressure as measured by this test method. This test method is limited to samples having a boiling range greater than 55.5 °C (100 °F), and having a vapor pressure sufficiently low to permit sampling at ambient temperature.
Note 1: Since a boiling range is the difference between two temperatures, only the constant of 1.8 °F/°C is used in the conversion of the temperature range from one system of units to another.
1.1.1 Procedure A (Sections 6 – 14)—Allows a larger selection of columns and analysis conditions such as packed and capillary columns as well as a Thermal Conductivity Detector in addition to the Flame Ionization Detector. Analysis times range from 14 min to 60 min.
1.1.2 Procedure B (Sections 15 – 23)—Is restricted to only 3 capillary columns and requires no sample dilution. In addition, Procedure B is used not only for the sample types described in Procedure A but also for the analysis of samples containing biodiesel mixtures B5, B10, and B20. The analysis time, when using Procedure B (Accelerated D2887), is reduced to about 8 min.
1.2 This test method is not to be used for the analysis of gasoline samples or gasoline components. These types of samples must be analyzed by Test Method D7096.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´2
Designation: D2887 − 19a
Designation: 406
Standard Test Method for
Boiling Range Distribution of Petroleum Fractions by Gas
1,2
Chromatography
This standard is issued under the fixed designation D2887; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Editorially corrected Table 3 in March 2020.
2
ε NOTE—Editorially corrected Table X6.1 in October 2020.
1. Scope* 1.2 This test method is not to be used for the analysis of
gasoline samples or gasoline components. These types of
1.1 Thistestmethodcoversthedeterminationoftheboiling
samples must be analyzed by Test Method D7096.
range distribution of petroleum products. The test method is
1.3 The values stated in SI units are to be regarded as
applicable to petroleum products and fractions having a final
standard. The values given in parentheses after SI units are
boiling point of 538°C (1000°F) or lower at atmospheric
providedforinformationonlyandarenotconsideredstandard.
pressure as measured by this test method. This test method is
1.4 This standard does not purport to address all of the
limited to samples having a boiling range greater than 55.5°C
safety concerns, if any, associated with its use. It is the
(100°F),andhavingavaporpressuresufficientlylowtopermit
responsibility of the user of this standard to establish appro-
sampling at ambient temperature.
priate safety, health, and environmental practices and deter-
NOTE 1—Since a boiling range is the difference between two
mine the applicability of regulatory limitations prior to use.
temperatures, only the constant of 1.8°F⁄°C is used in the conversion of
1.5 This international standard was developed in accor-
the temperature range from one system of units to another.
dance with internationally recognized principles on standard-
1.1.1 Procedure A (Sections 6–14)—Allows a larger ization established in the Decision on Principles for the
selection of columns and analysis conditions such as packed Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
and capillary columns as well as a Thermal Conductivity
Barriers to Trade (TBT) Committee.
DetectorinadditiontotheFlameIonizationDetector.Analysis
times range from 14min to 60min.
2. Referenced Documents
1.1.2 Procedure B (Sections 15–23)—Is restricted to only
3
2.1 ASTM Standards:
3 capillary columns and requires no sample dilution. In
D86Test Method for Distillation of Petroleum Products and
addition, Procedure B is used not only for the sample types
Liquid Fuels at Atmospheric Pressure
described in Procedure A but also for the analysis of samples
D1160TestMethodforDistillationofPetroleumProductsat
containing biodiesel mixtures B5, B10, and B20. The analysis
Reduced Pressure
time,whenusingProcedureB(AcceleratedD2887),isreduced
D2892Test Method for Distillation of Crude Petroleum
to about 8min.
(15-Theoretical Plate Column)
D4057Practice for Manual Sampling of Petroleum and
Petroleum Products
1
This test method is under the jurisdiction of ASTM Committee D02 on
D4626Practice for Calculation of Gas Chromatographic
Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of
Response Factors
Subcommittee D02.04.0H on Chromatographic Distribution Methods.
D6300Practice for Determination of Precision and Bias
Current edition approved Dec. 1, 2019. Published January 2020. Originally
ɛ1
approved in 1973. Last previous edition approved in 2019 as D2887–19 . DOI: Data for Use in Test Methods for Petroleum Products,
10.1520/D2887-19AE02.
2
This standard has been developed through the cooperative effort between
3
ASTM International and the Energy Institute, London. The EI and ASTM For referenced ASTM standards, visit the ASTM website, www.astm.org, or
International logos imply that the ASTM International and EI standards are contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
technically equivalent, but does not imply that both standards are editorially Standards volume information, refer to the standard’s Document Summary page on
identical. the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´2
D2887 − 19a
Liquid Fuels, and Lubricants chromatographic signal is considered to have returned to
D6708Practice for StatisticalAssessment and Improvement baseline after
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
´2 ´2
Designation: D2887 − 19a D2887 − 19a
Designation: 406
Standard Test Method for
Boiling Range Distribution of Petroleum Fractions by Gas
1,2
Chromatography
This standard is issued under the fixed designation D2887; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1
ε NOTE—Editorially corrected Table 3 in March 2020.
2
ε NOTE—Editorially corrected Table X6.1 in October 2020.
1. Scope*
1.1 This test method covers the determination of the boiling range distribution of petroleum products. The test method is
applicable to petroleum products and fractions having a final boiling point of 538 °C (1000 °F) or lower at atmospheric pressure
as measured by this test method. This test method is limited to samples having a boiling range greater than 55.5 °C (100 °F), and
having a vapor pressure sufficiently low to permit sampling at ambient temperature.
NOTE 1—Since a boiling range is the difference between two temperatures, only the constant of 1.8 °F ⁄°C is used in the conversion of the temperature
range from one system of units to another.
1.1.1 Procedure A (Sections 6 – 14)—Allows a larger selection of columns and analysis conditions such as packed and capillary
columns as well as a Thermal Conductivity Detector in addition to the Flame Ionization Detector. Analysis times range from
14 min to 60 min.
1.1.2 Procedure B (Sections 15 – 23)—Is restricted to only 3 capillary columns and requires no sample dilution. In addition,
Procedure B is used not only for the sample types described in Procedure A but also for the analysis of samples containing biodiesel
mixtures B5, B10, and B20. The analysis time, when using Procedure B (Accelerated D2887), is reduced to about 8 min.
1.2 This test method is not to be used for the analysis of gasoline samples or gasoline components. These types of samples must
be analyzed by Test Method D7096.
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are provided for
information only and are not considered standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of
regulatory limitations prior to use.
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility of Subcommittee
D02.04.0H on Chromatographic Distribution Methods.
ɛ1
Current edition approved Dec. 1, 2019. Published January 2020. Originally approved in 1973. Last previous edition approved in 2019 as D2887 – 19 . DOI:
10.1520/D2887-19AE01.10.1520/D2887-19AE02.
2
This standard has been developed through the cooperative effort between ASTM International and the Energy Institute, London. The EI and ASTM International logos
imply that the ASTM International and EI standards are technically equivalent, but does not imply that both standards are editorially identical.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
´2
D2887 − 19a
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
3
2.1 ASTM Standards:
D86 Test Method for Distillation of Petroleum Products and Liquid Fuels at Atmospheric Pressure
D1160 Test Method for Distillation of Petroleum Products at Reduced Pressure
D2892 Test Method for Distillation of Crude Petroleum (15-Theoretical Plate Column)
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4626 Practice for Calculation of Gas Chromatographic Response Factors
D6300 Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products, Liquid Fuels, and
Lubrica
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.