ASTM F1068-90(2018)

Standard Specification for Doors, Double, Gastight/Airtight, Individually Dogged, for Marine Use

ABSTRACT
This specification covers the principal dimensions and the mechanical requirements for manufacturing individually dogged, airtight/gastight double doors of steel and aluminum construction for personnel access through bulkheads, complete with frames, intended to maintain the structural and the air and gas tightness integrity of the bulkheads.
SCOPE
1.1 This specification, to be used in conjunction with Specification F1073, covers the principal dimensions and the mechanical requirements for manufacturing steel and aluminum individually dogged, airtight/gastight double doors for personnel access through bulkheads, complete with frames, intended to maintain the structural and the air and gas tightness integrity of the bulkheads.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the Test Methods portion, Section 6, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 31-Mar-2018
• ICS: 47.020.10 - Hulls and their structure elements
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.03 - Outfitting and Deck Machinery

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: F1068 − 90 (Reapproved 2018) An American National Standard
Standard Specification for
Doors, Double, Gastight/Airtight, Individually Dogged, for
1
Marine Use
This standard is issued under the fixed designation F1068; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope F1073 Specification for Door Fittings, for Watertight
/Gastight /Airtight, Weathertight, and Non-Tight Doors,
1.1 This specification, to be used in conjunction with
for Marine Use
Specification F1073, covers the principal dimensions and the
3
2.2 ABS Standard:
mechanical requirements for manufacturing steel and alumi-
Rules for Building and Classing Steel Vessels
num individually dogged, airtight/gastight double doors for
4
2.3 Military Standards:
personnel access through bulkheads, complete with frames,
MIL-R-900 Rubber Gasket Material, 45 Durometer Hard-
intended to maintain the structural and the air and gas tightness
ness
integrity of the bulkheads.
MIL-C-81706 Coating, Aluminum and Aluminum Alloys
1.2 The values stated in inch-pound units are to be regarded
MIL-P-24441 Epoxy-Polyamide Paint
as standard. The values given in parentheses are mathematical
DoD-STD-2138 Metal Sprayed Coating System for Corro-
conversions to SI units that are provided for information only
sion Protection
and are not considered standard.
TT-E-490 Enamel, Silicone Alkyd Copolymer, Semi-Gloss,
1.3 The following precautionary caveat pertains only to the
Exterior
Test Methods portion, Section 6, of this specification: This ZZ-R-765 Rubber, Silicone
standard does not purport to address all of the safety concerns,
3. Ordering Information
if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety, health, and
3.1 Ordering for doors under this specification shall include
environmental practices and determine the applicability of the following:
regulatory limitations prior to use.
3.1.1 Material of doors,
1.4 This international standard was developed in accor- 3.1.2 Nominal and ASTM designations, fixed lights or no
dance with internationally recognized principles on standard-
lights,
ization established in the Decision on Principles for the
3.1.3 Quantity, and
Development of International Standards, Guides and Recom-
3.1.4 Location of active and inactive panels.
mendations issued by the World Trade Organization Technical
3.2 Inspection and acceptance of doors shall be agreed upon
Barriers to Trade (TBT) Committee.
between the purchaser and the supplier.
2. Referenced Documents
4. Construction, Shape, and Dimensions
2
2.1 ASTM Standards:
4.1 The construction, shape, and clear opening dimensions
A36/A36M Specification for Carbon Structural Steel
shall be as shown in Fig. 1 and Table 1; in addition, they shall
A131/A131M Specification for Structural Steel for Ships
conform to the following requirements:
B209 Specification for Aluminum and Aluminum-Alloy
4.1.1 Door frames shall be supplied as indicated in Fig. 1.
Sheet and Plate
The corner radius inside of door frame shall be 8 in. (203 mm).
4.1.2 Dogs shall be located on the door panels unless
otherwise specified.
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
4.1.3 The doors shall be fitted with dogs, hinges, hasp and
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
staple assemblies, grab handles, label plates, and hook assem-
Outfitting and Deck Machinery.
Current edition approved April 1, 2018. Published May 2018. Originally blies.
approved in 1987. Last previous edition approved in 2012 as F1068 – 90 (2012).
DOI: 10.1520/F1068-90R18.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American Bureau of Shipping (ABS), ABS Plaza, 16855
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Northchase Dr., Houston, TX 77060, http://www.eagle.org.
4
Standards volume information, refer to the standard’s Document Summary page on Available from DLA Document Services, Building 4/D, 700 Robbins Ave.,
the ASTM website. Philadelphia, PA 19111-5094, http://quicksearch.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1068 − 90 (2018)
NOTE 1—1 in. = 25.4 mm.
FIG. 1 Typical Double-Door Details
4.1.4 The position of the grab handles shall be located at the 5.1.1 The door panels, upon completion, shall be straight
1
center of the height of each door panel. with a tolerance of 6 ⁄16 in. (1.6 mm)
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: F1068 − 90 (Reapproved 2012) F1068 − 90 (Reapproved 2018)An American National Standard
Standard Specification for
Doors, Double, Gastight/Airtight, Individually Dogged, for
1
Marine Use
This standard is issued under the fixed designation F1068; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification, to be used in conjunction with Specification F1073, covers the principal dimensions and the mechanical
requirements for manufacturing steel and aluminum individually dogged, airtight/gastight double doors for personnel access
through bulkheads, complete with frames, intended to maintain the structural and the air and gas tightness integrity of the
bulkheads.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3 The following precautionary caveat pertains only to the Test Methods portion, Section 6, of this specification: This standard
does not purport to address all of the safety concerns concerns, if any, associated with its use. It is the responsibility of the user
of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the applicability
of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A36/A36M Specification for Carbon Structural Steel
A131/A131M Specification for Structural Steel for Ships
B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate
F1073 Specification for Door Fittings, for Watertight /Gastight /Airtight, Weathertight, and Non-Tight Doors, for Marine Use
3
2.2 ABS Standard:
Rules for Building and Classing Steel Vessels
4
2.3 Military Standards:
MIL-R-900 Rubber Gasket Material, 45 Durometer Hardness
MIL-C-81706 Coating, Aluminum and Aluminum Alloys
MIL-P-24441 Epoxy-Polyamide Paint
DoD-STD-2138 Metal Sprayed Coating System for Corrosion Protection
TT-E-490 Enamel, Silicone Alkyd Copolymer, Semi-Gloss, Exterior
ZZ-R-765 Rubber, Silicone
3. Ordering Information
3.1 Ordering for doors under this specification shall include the following:
3.1.1 Material of doors,
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
Outfitting and Deck Machinery.
Current edition approved Oct. 1, 2012April 1, 2018. Published October 2012May 2018. Originally approved in 1987. Last previous edition approved in 20072012 as
F1068 – 90 (2007).(2012). DOI: 10.1520/F1068-90R12.10.1520/F1068-90R18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Bureau of Shipping (ABS), ABS Plaza, 16855 Northchase Dr., Houston, TX 77060, http://www.eagle.org.
4
Available from Standardization Documents, Order Desk, Bldg. 4, Section D, DLA Document Services, Building 4/D, 700 Robbins Ave., Philadelphia, PA 19111-5094,
ATTN: NPODS.http://quicksearch.dla.mil.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
F1068 − 90 (2018)
3.1.2 Nominal and ASTM designations, fixed lights or no lights,
3.1.3 Quantity, and
3.1.4 Location of active and inactive panels.
3.2 Inspection and acceptance of doors shall be agreed upon between the purchaser and the supplier.
4. Construction, Shape, and Dimensions
4.1 The construction, shape, and clear opening dimensions shall be as shown in Fig. 1 and Table 1; in addition, they shall
conform to the following requirements:
4.1.1 Door frames shall be supplied as indicated in Fig. 1. The corner radius inside of door frame shall be 8 in. (203 mm).
4.1.2 Dogs
...