iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM F1072-94(2023)

(Specification)

Standard Specification for Expanded-Metal Doors

Standard Specification for Expanded-Metal Doors

ABSTRACT
This specification covers steel expanded-metal doors suitable for installation in expanded-metal bulkheads, structural bulkheads, and structural arches. Expanded-metal doors are furnished in four types: Type I (right hand), Type II (left hand), Type III (right hand reverse) and Type IV (left hand reverse). Doors shall be furnished with the vertical support channels and top angle in place. A temporary brace shall be included at the frame bottom to prevent racking. Doors shall be fitted with rubber-tipped bumpers and a manually operated catch for holding doors in an open position. Provision shall be made for the installation of a rim latch set operated by knobs on both sides. Doors and frames shall be free from all cracks, burrs, sharp edges, and other defects.
SCOPE
1.1 This specification covers steel expanded-metal doors suitable for installation in expanded-metal bulkheads, structural bulkheads, and structural arches.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

Status
Published
Publication Date
30-Jun-2023
ICS
47.020.10 - Hulls and their structure elements
Technical Committee
F25 - Ships and Marine Technology
Drafting Committee
F25.03 - Outfitting and Deck Machinery
Current Stage
Ref Project

Relations

Refers
ASTM D3951-18(2023) - Standard Practice for Commercial Packaging
Effective Date
01-Oct-2023
Refers
ASTM D3951-18 - Standard Practice for Commercial Packaging
Effective Date
01-May-2018
Refers
ASTM D3951-15 - Standard Practice for Commercial Packaging
Effective Date
01-Dec-2015
Refers
ASTM F783-88(2013) - Standard Specification for Staple, Handgrab, Handle, and Stirrup Rung
Effective Date
01-May-2013
Refers
ASTM A36/A36M-12 - Standard Specification for Carbon Structural Steel
Effective Date
01-Nov-2012
Refers
ASTM D3951-10 - Standard Practice for Commercial Packaging
Effective Date
15-Aug-2010
Refers
ASTM A167-99(2009) - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip (Withdrawn 2014)
Effective Date
01-May-2009
Refers
ASTM A36/A36M-08 - Standard Specification for Carbon Structural Steel
Effective Date
15-May-2008
Refers
ASTM F783-88(2008) - Standard Specification for Staple, Handgrab, Handle, and Stirrup Rung
Effective Date
01-May-2008
Refers
ASTM A36/A36M-05 - Standard Specification for Carbon Structural Steel
Effective Date
01-Mar-2005
Refers
ASTM A167-99(2004) - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet, and Strip
Effective Date
01-Sep-2004
Refers
ASTM A36/A36M-04 - Standard Specification for Carbon Structural Steel
Effective Date
01-Apr-2004
Refers
ASTM F783-88(2003) - Standard Specification for Staple, Handgrab, Handle, and Stirrup Rung
Effective Date
01-Dec-2003
Refers
ASTM A36/A36M-03a - Standard Specification for Carbon Structural Steel
Effective Date
10-May-2003
Refers
ASTM A36/A36M-03 - Standard Specification for Carbon Structural Steel
Effective Date
10-Apr-2003

Buy Standard

ASTM F1072-94(2023) - Standard Specification for Expanded-Metal DoorsASTM F1072-94(2023) - Standard Specification for Expanded-Metal Doors
PreviousNext
Technical specification
ASTM F1072-94(2023) - Standard Specification for Expanded-Metal Doors
English language
7 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)


This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: F1072 − 94 (Reapproved 2023) An American National Standard
Standard Specification for
Expanded-Metal Doors
This standard is issued under the fixed designation F1072; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3. Classification
3.1 Expanded-metal doors are furnished in four types (see
1.1 This specification covers steel expanded-metal doors
Detail “J”) as follows:
suitable for installation in expanded-metal bulkheads, struc-
3.1.1 Type I—Right hand (RH).
tural bulkheads, and structural arches.
3.1.2 Type II—Left hand (LH).
1.2 The values stated in inch-pound units are to be regarded
3.1.3 Type III—Right hand reverse (RHR).
as standard. The values given in parentheses are mathematical
3.1.4 Type IV—Left hand reverse (LHR).
conversions to SI units that are provided for information only
and are not considered standard.
4. Ordering Information
1.3 This international standard was developed in accor-
4.1 Orders for doors under this specification shall include
dance with internationally recognized principles on standard-
this specification number and type.
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
5. Materials and Manufacture
mendations issued by the World Trade Organization Technical
5.1 Materials—See Table 1.
Barriers to Trade (TBT) Committee.
5.2 Manufacture:
5.2.1 Doors shall be furnished with the vertical support
2. Referenced Documents
channels and top angle in place. A temporary brace shall be
2.1 ASTM Standards:
included at the frame bottom to prevent racking.
A36/A36M Specification for Carbon Structural Steel
5.2.2 Welding shall be in accordance with AWS D1.1
A167 Specification for Stainless and Heat-Resisting
Structural Welding Code or ABS Rules for Building and
Chromium-Nickel Steel Plate, Sheet, and Strip (With-
Classing Steel Vessels.
drawn 2014)
D3951 Practice for Commercial Packaging
6. Installation Requirements
F783 Specification for Staple, Handgrab, Handle, and Stir-
6.1 Doors shall be fitted with rubber-tipped bumpers and a
rup Rung
manually operated catch for holding doors in an open position.
2.2 Other Documents:
These shall be furnished and installed by others.
ABS Rules for Building and Classing Steel Vessels
6.2 Provision shall be made for the installation of a rim latch
AWS D1.1 Structural Welding Code
set operated by knobs on both sides. This hardware shall be
furnished and installed by others.
6.3 Padlocks shall be furnished by others.
This specification is under the jurisdiction of ASTM Committee F25 on Ships
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
6.4 Any holes needed in the frame for installation in
Outfitting and Deck Machinery.
expanded-metal or other types of bulkheads shall be made at
Current edition approved July 1, 2023. Published July 2023. Originally approved
installation by others.
in 1987. Last previous edition approved in 2018 as F1072 – 94 (2018). DOI:
10.1520/F1072-94R23.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
7. Dimensions and Tolerances
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
7.1 Dimensions are as indicated in Figs. 1-8 and Table 1.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
7.2 Tolerance—6 ⁄16 in. (1.5 mm).
The last approved version of this historical standard is referenced on
www.astm.org.
Available from American Bureau of Shipping (ABS), ABS Plaza, 16855 8. Workmanship, Finish, and Appearance
Northchase Dr., Houston, TX 77060, http://www.
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM F821/F821M-23(Specification)
Standard Specification for Domestic Use Doors and Frames, Steel, Interior, Marine

ABSTRACT
This specification covers the design and dimensional requirements for the construction of standard and custom-built interior steel doors and frames intended for use in staterooms, lavatories, passageways, and other weather-protected areas of ships, including U.S. Coast Guard certificated vessels, with domestic routes. The doors and frames are to be of hollow metal construction with the door insulated for sound or fire. The doors and frames shall conform to the specified dimensional and construction procedures established for each class and type, which shall be indicated in the ordering information.
SCOPE
1.1 This specification covers the construction of standard and custom-built interior steel doors and frames for ships including U.S. Coast Guard certificated vessels with domestic routes.  
1.2 Doors and frames are to be hollow metal construction with the door insulated for sound or fire.  
1.3 The doors are intended for use in staterooms, lavatories, passageways, and other areas protected from weather.  
1.4 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    6 pages
    English language
    sale 15% off
  • Technical specification
    6 pages
    English language
    sale 15% off
ASTM
ASTM F783-88(2023)(Specification)
Standard Specification for Staple, Handgrab, Handle, and Stirrup Rung

ABSTRACT
This specification provides the design and dimensional requirements for the construction of steel staples, handgrabs, and handles that are for use on steel structures including all parts of a ships' structure as necessary, as well as individual stirrup rungs that are for use on bulkheads or structures as deemed necessary.
SCOPE
1.1 This specification covers design, construction for steel staples, handgrabs, handles, and individual stirrup rungs.  
1.2 The staples, handgrabs, and handles depicted in this specification are for use on steel structures including all parts of ships' structure as necessary. The individual stirrup rungs are for use on bulkheads or structure as deemed necessary.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    3 pages
    English language
    sale 15% off
ASTM
ASTM F985-18(2023)(Specification)
Standard Specification for Pilot Platform

ABSTRACT
This specification provides design and construction details for Panama Canal pilot platforms placed aboard the vessel. Platforms shall conform to the requirements of the Panama Canal Commission and Title 35 of the Code of Federal Regulations. The platforms shall be welded-aluminum construction. Decking shall be serrated-aluminum grating. Canopy shall be of vinyl-nylon construction with sewn seams and metallic grommets. Finally, canopy tie-downs shall be of a specified nylon line thickness.
SCOPE
1.1 This specification covers design and construction details for pilot platforms.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM F1068-90(2023)(Specification)
Standard Specification for Doors, Double, Gastight/Airtight, Individually Dogged, for Marine Use

ABSTRACT
This specification covers the principal dimensions and the mechanical requirements for manufacturing individually dogged, airtight/gastight double doors of steel and aluminum construction for personnel access through bulkheads, complete with frames, intended to maintain the structural and the air and gas tightness integrity of the bulkheads.
SCOPE
1.1 This specification, to be used in conjunction with Specification F1073, covers the principal dimensions and the mechanical requirements for manufacturing steel and aluminum individually dogged, airtight/gastight double doors for personnel access through bulkheads, complete with frames, intended to maintain the structural and the air and gas tightness integrity of the bulkheads.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following precautionary caveat pertains only to the Test Methods portion, Section 6, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1385-07(2023)(Practice)
Standard Practice for Platforms in Cargo Tanks

SIGNIFICANCE AND USE
3.1 This practice establishes the procedure for the construction and installation of platforms to be fabricated and installed by the shipyards within the cargo tanks.
SCOPE
1.1 This practice covers design, construction, and installation criteria for platforms in cargo tanks.  
1.2 Where platforms are attached to ladders see Figs. 1-4.
FIG. 1 Cargo Platform—Bulkhead  
FIG. 2 Cargo Platform Elevation  
FIG. 3 Cargo Platform—Girder  
FIG. 4 Cargo Platforms Showing Typical Sections  
1.3 The values stated in SI units are to be regarded as standard. The values given in parentheses after SI units are included for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM F1071-94(2023)(Specification)
Standard Specification for Expanded-Metal Bulkhead Panels

ABSTRACT
This specification covers steel expanded-metal bulkhead panels suitable for use in storerooms, shops, and as protection against personnel hazards. Bulkhead panels are furnished in three types as follows: type I - universal bulkhead panels for use as both a right-hand or left-hand panel, type II - right-hand bulkhead panel, and type III - left-hand bulkhead panel. Bulkhead panels are furnished in two classes as follows: class A - bulkhead panels, 2 ft; and class B - bulkhead panels, 3 ft. Expanded-metal panels shall be free from all cracks, burrs, sharp edges, and other defects. The panel manufacturer shall apply a nonhazardous corrosion-inhibiting primer coating to all panel assemblies.
SCOPE
1.1 This specification covers steel expanded-metal bulkhead panels suitable for use in storerooms, shops, and as protection against personnel hazards.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3040/F3040M-13(2023)(Test Method)
Standard Test Method for Mechanical Static Load Testing of Non-Structural Marine Joiner Bulkheads

SIGNIFICANCE AND USE
4.1 The test method provides information regarding the behavior of a non-structural A, B, or C-Class bulkhead panel system under a static load. Test data for load, moment and deformation is measured.  
4.2 Static load test of non-structural marine joiner panel systems provide a standard method of obtaining data for research and development, quality control, acceptance or rejection under specifications, and special purposes. The tests cannot be considered significant for engineering design in applications differing widely from the loading type and magnitude of the standard test. Such applications shall require additional tests.
SCOPE
1.1 This test method covers a procedure for evaluating the strength of non structural marine joiner of A, B, and C-Class bulkhead and liner systems. A, B, and C-Class bulkheads are defined and discussed in 2.1.  
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, to ensure conformance with the standard, each system shall be used independently of the other, and values from the two systems shall not be combined.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1455-92(2022)(Guide)
Standard Guide for Selection of Structural Details for Ship Construction

ABSTRACT
This guide provides a recommended list of selected ship structure details for use in ship construction. Structural details which have failed in service and are not recommended for use in ship construction are included as well. This guide is intended to convey the lessons learned on different configurations of ship structure details, not the dimensions, thickness, or construction methods which would result from structural calculations. Details are shown for the ten families of structural details, which are: beam brackets, clearance cut-outs, gunwale connections, miscellaneous cut-outs, non-tight collars, panel stiffeners, stanchion ends, stiffener ends, tight collars, and tripping brackets. Evaluation of details is based on in-service experience as described in "Design Guide for Structural Details". Data for over 400 details is summarized and rated by observed relative successful performance. Each of the ten families of details includes configurations with no signs of failures. The details without failures within each family group are shown in descending order of numbers observed. Those details with failures are shown in ascending order of failures (percentages are indicated for each). Thus the first detail shown in each family group has the best observed service performance and is most highly recommended while the last has the highest failure rate and therefore least desirable. The details provide guidance in the selection of structural detail configurations in future design and repair of such details.
SCOPE
1.1 This guide provides a recommended list of selected ship structure details for use in ship construction.  
1.2 Structural details which have failed in service and are not recommended for use in ship construction are included as well.  
1.3 This guide is intended to convey the lessons learned on different configurations of ship structure details, not the dimensions, thickness, or construction methods which would result from structural calculations.4  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    19 pages
    English language
    sale 15% off
ASTM
ASTM F987-04(2022)(Specification)
Standard Specification for Portable Intermediate Flush Deck Stanchion

ABSTRACT
This specification covers the design, construction, and installation details of two-course (Type I) and three-course (Type II) portable intermediate flush deck stanchions that are used on interior and exterior decks to provide temporary protection and minimize the danger of personnel falling overboard or to a lower level in the ship in areas where the installation of a fixed system would interfere with vessel operations. This specification does not include the requirements for the chain or wire rope lines to be supported by the stanchion. The stanchions shall be free of weld spatters, slag splinters, sharp edges, burrs, projections, and other defects hazardous to personnel, and the deck sockets shall be hammer tested for soundness and strength.
SCOPE
1.1 This specification covers the design, construction, and installation of intermediate portable flush deck stanchions. Intermediate stanchion is defined as any stanchion that is not an end or corner stanchion.  
1.2 Stanchions shall be used on interior and exterior decks, to provide temporary protection to minimize the danger of personnel falling overboard or to a lower level in the ship in areas where the installation of a fixed system would interfere with vessel operations.  
1.3 Stanchions may be used with 3/8-in. (9.5-mm) galvanized close link chain or wire rope lifelines 9/16-in. (14-mm) top course, 7/16-in. (11-mm) lower courses.  
1.4 This specification covers only the stanchions and does not cover requirements for the chain or wire rope lines to be supported by the stanchion.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM F1092-19(Specification)
Standard Specification for Fiberglass (GRP) Pultruded Open-Weather Storm and Guard, Square Railing Systems

ABSTRACT
This specification provides the material requirements, construction, installation, and testing requirements for open-weather deck, storm-and-guard, fiberglass square railing systems. Components are to be manufactured by the pultrusion process. Handrails and stanchions shall be fiberglass pultruded square tube available in the following two types: Type 1F and Type 2F. Test at least one end stanchion and one other stanchion of each platform or deck by application of a load horizontally in accordance with the specification.
SCOPE
1.1 This specification provides the material requirements, construction, installation, and testing requirements for open-weather deck, storm-and-guard, fiberglass square railing systems. Components are to be manufactured by the pultrusion process.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the test methods portion, Section 9, of this specification:  This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    10 pages
    English language
    sale 15% off
  • Technical specification
    10 pages
    English language
    sale 15% off