ASTM C1417M-04
(Specification)Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric)
Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design (Metric)
SCOPE
1.1 This specification covers the manufacture and acceptance of precast concrete pipe designed to conform to the owner's design requirements and to the ASCE 15-93 or an equivalent design specification.
Note 1—The section on evaluation of core test results (14.3.3) and the Appendix are currently being reballoted.
1.2 This specification is the SI companion to Specification C 1417.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 1417M – 04
METRIC
Standard Specification for
Manufacture of Reinforced Concrete Sewer, Storm Drain,
1
and Culvert Pipe for Direct Design [Metric]
This standard is issued under the fixed designation C 1417M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope C 150 Specification for Portland Cement
C 309 Specification for Liquid Membrane-Forming Com-
1.1 This specification covers the manufacture and accep-
pound for Curing Concrete
tance of precast concrete pipe designed to conform to the
C 497 Test Methods for Concrete Pipe, Manhole Sections,
owner’s design requirements and to the ASCE 15-93 or an
or Tile
equivalent design specification.
C 595 Specification for Blended Hydraulic Cements (Met-
NOTE 1—The section on evaluation of core test results (14.3.3) and the
ric)
Appendix are currently being reballoted.
C 618 Specification for Coal Fly Ash and Raw or Calcined
1.2 This specification is the SI companion to Specification
Natural Pozzolan for Use as a Mineral Admixture in
C 1417.
Portland Cement Concrete
C 655 Specification for Reinforced Concrete D-Load Cul-
2. Referenced Documents
vert, Storm Drain, and Sewer Pipe
2
2.1 ASTM Standards:
C 822 Terminology Relating to Concrete Pipe and Related
A 82 Specification for Steel Wire, Plain, for Concrete Re-
Products
inforcement
2.2 Other Standards:
A 185 SpecificationforSteelWeldedWireFabric,Plain,for
ASCE 15-93 Standard Practice for the Direct Design of
Concrete Reinforcement
Buried Precast Reinforced Concrete Pipe Using Standard
3
A 496 Specification for Steel Wire, Deformed, for Concrete
Installations (SIDD)
Reinforcement
ACI 318 Building Code Requirements for Reinforced Con-
4
A 497 Specification for Steel Welded Wire Fabric, De-
crete
formed, for Concrete Reinforcement
3. Terminology
A 615/A 615M Specification for Deformed and Plain
Billet-Steel Bars for Concrete Reinforcement
3.1 Definitions:
C 31 Practice for Making and Curing Concrete Test Speci-
3.1.1 For definitions of terms relating to concrete pipe, see
mens in the Field
Terminology C 822.
C 33 Specification for Concrete Aggregates
3.1.2 group of pipe sections—each day’s production run of
C 39 Test Method for Compressive Strength of Cylindrical
pipesectionsofasingleconcretestrengthforaspecificproject.
Concrete Specimens
3.1.3 lot of pipe sections—total of the number of groups of
C 76 Specification for Reinforced Concrete Culvert, Storm
pipe sections of a single concrete strength produced for a
Drain, and Sewer Pipe
specific project.
3.1.4 running average—average concrete compressive
strength of all groups of pipe sections of a single concrete
1
This specification is under the jurisdiction of ASTM Committee C13 on
strength produced for a specific project, generally determined
Concrete Pipe and is the direct responsibility of Subcommittee C13.05 on Least
as each group is tested.
Cost Analysis.
CurrenteditionapprovedOctober1,2004.PublishedNovember2004.Originally
approved in 1998. Last previous edition approved in 2003 as C 1417M–03.
2 3
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American Society of Civil Engineers, 345 E. 45th Street, New
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM York, NY 10017–2398.
4
Standards volume information, refer to the standard’s Document Summary page on Available from American Concrete Institute, P.O. Box 19150, Detroit, MI
the ASTM website. 48219.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C 1417M – 04
4. Basis of Acceptance of Design 6.2.3 Allowable Combinations of Cementitious Materials—
Thecombinationofcementitiousmaterialsusedintheconcrete
4.1 Manufacturing Design Data—The manufacturer shall
shall be one of the following:
submit the following manufacturing design data for the con-
6.2.3.1 Portland cement only.
crete pipe to the owner for approval.
6.2.3.2 Portland blast furnace slag cement only.
4.1.1 Pipe wall thickness.
6.2.3.3 Portland pozzolan cement only.
4.1.2 Concrete strength.
6.2.3.4 A combination of portland cement and fly ash or
4.1.3 Reinforcement:
pozzolan, wherein the proportion of fly ash is between 5 and
4.1.3.1 Specification,
25 % by weight (mass) of total cementitious material (portland
4.1.3.2 Reinforcement Type 1, 2, or 3, where:
cement plus fly ash).
Type 1: Smooth wire or plain bars
6.3 Aggregates—Aggregates shall conform to the require-
Type 2: Welded smooth wire fabric, 200 mm maximum spacing of
longitudinals
ments of Specification C 33, exce
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.