iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3131-97

(Specification)

Standard Specification for Isopropyl Acetate (99% Grade)

Standard Specification for Isopropyl Acetate (99% Grade)

SCOPE
1.1 This specification covers isopropyl acetate (99 % grade).
1.2 For specific hazard information and guidance, see the supplier's Material Safety Data Sheet for materials listed in this specification.
1.3 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off "to the nearest unit" in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E 29.

General Information

Status
Historical
Publication Date
09-May-2002
ICS
71.080.10 - Aliphatic hydrocarbons
Technical Committee
D01 - Paint and Related Coatings, Materials, and Applications
Drafting Committee
D01.35 - Solvents, Plasticizers, and Chemical Intermediates
Current Stage
Ref Project

Relations

Replaced By
ASTM D3131-02 - Standard Specification for Isopropyl Acetate (99% Grade)
Effective Date
10-May-2002

Buy Standard

ASTM D3131-97 - Standard Specification for Isopropyl Acetate (99% Grade)ASTM D3131-97 - Standard Specification for Isopropyl Acetate (99% Grade)
PreviousNext
Technical specification
ASTM D3131-97 - Standard Specification for Isopropyl Acetate (99% Grade)
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or
withdrawn. Contact ASTM International (www.astm.org) for the latest information.
Designation: D 3131 – 97
AMERICAN SOCIETY FOR TESTING AND MATERIALS
100 Barr Harbor Dr., West Conshohocken, PA 19428
Reprinted from the Annual Book of ASTM Standards. Copyright ASTM
Standard Specification for
1
Isopropyl Acetate (99 % Grade)
This standard is issued under the fixed designation D 3131; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope PPP-C-2020 Chemicals, Liquid, Dry, and Paste: Packaging
6
of
1.1 This specification covers isopropyl acetate (99 %
grade).
3. Properties
1.2 For specific hazard information and guidance, see the
3.1 Isopropyl acetate (99 % grade) shall conform to the
supplier’s Material Safety Data Sheet for materials listed in this
following requirements:
specification.
Apparent specific gravity:
20/20°C 0.870 to 0.874
2. Referenced Documents
25/25°C 0.865 to 0.869
2.1 ASTM Standards: Color, Pt-Co scale, max 10
Distillation range, 760 mmHg : (see
D 268 Guide for Sampling and Testing Volatile Solvents
Note 1)
and Chemical Intermediates for Use in Paint and Related
Initial boiling point, min, °C 85
2
Coatings and Materials Dry point, max, °C 90
Nonvolatile matter, mg/100 mL, max 5
D 1078 Test Method for Distillation Range of Volatile
Odor nonresidual
2
Organic Liquids
Water, weight %, max 0.2. This quantitative water limit
D 1209 Test Method for Color of Clear Liquids (Platinum-
ensures that 1 volume of the ma-
2
terial is miscible without turbidity
Cobalt Scale)
with 19 volumes of 99 % heptane
D 1296 Test Method for Odor of Volatile Solvents and
at 20°C.
2
Diluents Acidity (free acid as acetic acid), 0.01, equivalent to 0.093 mg of
weight %, max KOH per gram of sample
D 1353 Test Method for Nonvolatile Matter in Volatile
Purity, weight %, min 99.0
Solvents for Use in Paint, Varnish, Lacquer, and Related
2
NOTE 1—Optional as agreed upon between the buyer and the seller.
Products
D 1364 Test Method for Water in Volatile Solvents (Karl
4. Sampling
2
Fischer Reagent Titration Method)
4.1 The material shall be sampled in accordance with
D 1476 Test Method for Heptane Miscibility of Lacquer
2 Practice E 300.
Solvents
D 1613 Test Method for Acidity in Volatile Solvents and
5. Test Methods
Chemical Intermediates Used in Paint, Varnish, Lacquer,
5.1 The properties enumerated in this specification shall be
2
and Related Products
determined in accordance with the following ASTM test
D 3545 Test Method for Alcohol Content and Purity of
methods:
2
Acetate Esters by Gas Chromatography
5.1.1 Apparent Specific Gravity—Determine the ap
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3131-07(2021)(Specification)
Standard Specification for Isopropyl Acetate (99 % Grade)

ABSTRACT
This specification establishes the properties and requirements for isopropyl acetate. Specimens shall be sampled and tested as appropriate, and adhere accordingly to specified values of the following properties: apparent specific gravity; color (Pt-Co scale); distillation range (initial boiling point and dry point); nonvolatile matter content; odor; water content; acidity (free acid as acetic acid); and purity.
SCOPE
1.1 This specification covers isopropyl acetate (99 % grade).  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 For specific hazard information and guidance, see the supplier’s Material Safety Data Sheet for materials listed in this specification.  
1.4 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D1836-07(2021)(Specification)
Standard Specification for Commercial Hexanes

ABSTRACT
This specification covers commercial hexanes used in the preparation of adhesives, coatings, and printing inks, as raw materials in chemical synthesis, and as solvents in various kinds of extraction operations. The commercial hexanes should conform to the specified requirements for aniline point, apparent specific gravity, bromine index, color Pt-Co, distillation range, kauri-butanol value, nonvolatile matter content, odor, sulfur content, and benzene content.
SCOPE
1.1 This specification covers the range of products commonly referred to as hexanes, which find uses in the preparation of adhesives, coatings, and printing inks, as raw materials in chemical synthesis operations, and as solvents in various kinds of extraction operations.  
1.2 The following applies to all specified limits in this standard; for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 For specific hazard information and guidance consult supplier’s Material Safety Data Sheet.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
ASTM
ASTM D7266-23(Test Method)
Standard Test Method for Analysis of Cyclohexane by Gas Chromatography (External Standard)

SIGNIFICANCE AND USE
5.1 This test method is suitable for setting specifications on the materials referenced in Table 1 and for use as an internal quality control tool where cyclohexane is produced or is used in a manufacturing process. It may also be used in development or research work involving cyclohexane.  
5.2 This test method is useful in determining the purity of cyclohexane with normal impurities present. If extremely high boiling or unusual impurities are present in the cyclohexane, this test method would not necessarily detect them and the purity calculation would be erroneous.
SCOPE
1.1 This test method covers the determination of the purity of cyclohexane by gas chromatography.  
1.2 This test method is applicable to the measurement of impurities in Table 1. This test method is applicable to samples with concentrations to 400 mg/kg, but may be applicable to a wider range. The limit of detection (LOD) is 1 mg/kg and the limit of quantitation (LOQ) is 3 mg/kg for benzene.
Note 1: The LOD and LOQ were calculated from the ILS data for benzene.  
1.3 The following applies for the purposes of determining the conformance of the test results using this test method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazard statements, see Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D7871-23(Test Method)
Standard Test Method for Analysis of Cyclohexane by Gas Chromatography (Effective Carbon Number)

SIGNIFICANCE AND USE
5.1 This test method is suitable for setting specifications on the materials referenced in Table 1 and for use as an internal quality control tool where cyclohexane is produced or is used in a manufacturing process. It may also be used in development or research work involving cyclohexane.  
5.2 This test method is useful in determining the purity of cyclohexane with normal impurities present. If extremely high boiling or unusual impurities are present in the cyclohexane, this test method would not necessarily detect them and the purity calculation would be erroneous.
SCOPE
1.1 This test method covers the determination of the purity of cyclohexane by gas chromatography.  
1.2 This test method has been found applicable to the measurement of impurities such as those found in Table 1, which are impurities that may be found in cyclohexane. The impurities can be analyzed over a range with an upper limit of 400 mg/kg by this method, but may be applicable to a wider range. The limit of detection (LOD) is 0.7 mg/kg and the limit of quantitation (LOQ) is 2.3 mg/kg.
Note 1: The LOD and LOQ were calculated from the ILS data for benzene.  
1.3 The following applies for the purposes of determining the conformance of the test results using this test method to applicable specifications: results shall be rounded off in accordance with the rounding-off method of Practice E29.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific hazards statements, see Section 8.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D5799-23(Test Method)
Standard Test Method for Determination of Peroxides in Butadiene

SIGNIFICANCE AND USE
4.1 Due to the inherent danger of peroxides in butadiene, specification limits are usually set for their presence. This test method will provide values that can be used to determine the peroxide content of a sample of commercial butadiene.  
4.2 Butadiene polyperoxide is a very dangerous product of the reaction between butadiene and oxygen that can occur. The peroxide has been reported to be the cause of some violent explosions in vessels that are used to store butadiene.
SCOPE
1.1 This test method covers the determination of peroxides in butadiene.  
1.2 This test method covers the concentrations range of 1 mg/kg to 10 mg/kg as available oxygen.  
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D2712-23(Test Method)
Standard Test Method for Determination of Hydrocarbon Impurities in High Purity Propylene by Gas Chromatography

SIGNIFICANCE AND USE
5.1 High-purity propylene is required as a feedstock for various manufacturing processes, and the presence of trace amounts of certain hydrocarbon impurities may have adverse effects on yield or catalyst life. This test method is suitable for use as a benchmark in setting commercial specifications, for use as an internal quality control tool, and for use in development or research work.
SCOPE
1.1 This test method is used for the determination of hydrocarbon impurities in propylene (propene) material of 97 % by mass or greater purity (concentrates). These impurities are determined in the concentration range of 0.35 mg/kg to 8575 mg/kg and includes the following components: methane, ethane, ethylene, propane, acetylene, isobutane, propadiene, normal butane, trans-2-butene, butene-1, isobutylene, cis-2-butene, isopentane, methylacetylene, normal pentane, and 1,3-butadiene.
Note 1: Optionally, the analysis may include the determination of pentenes/hexanes and heavier components, see 6.3.  
1.2 This test method does not determine non-hydrocarbon impurities, and additional tests may be necessary to fully characterize the propylene sample. However, for the purposes of this test, the purity of propylene is determined as the difference between the total of the determined analytes and 100 % (by difference).  
1.3 When this test method is being used for the determination of trace level impurities in high-purity propylene, the use of this test method for the analysis of propylene samples at lower purities is not recommended due to the potential for cross contamination between samples.  
1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities. The eLearning training course “Liquefied Petroleum Gases Sampling Safety” is available on the ASTM.org website.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    6 pages
    English language
    sale 15% off
  • Standard
    6 pages
    English language
    sale 15% off
ASTM
ASTM D2593-23(Test Method)
Standard Test Method for Butadiene Purity and Hydrocarbon Impurities by Gas Chromatography

SIGNIFICANCE AND USE
4.1 The trace hydrocarbon compounds listed can have an effect in the commercial use of butadiene. This test method is suitable for use in process quality control and in setting specifications.
SCOPE
1.1 This test method covers the determination of butadiene-1,3 purity and impurities such as propane, propylene, isobutane, n-butane, butene-1, isobutylene, propadiene, trans-butene-2, cis-butene-2, butadiene-1,2, pentadiene-1,4, and, methyl, dimethyl, ethyl, and vinyl acetylene in polymerization grade butadiene by gas chromatography. Impurities including butadiene dimer, carbonyls, inhibitor, and residue are measured by appropriate ASTM procedures and the results used to normalize the component distribution obtained by chromatography.  
Note 1: Other impurities present in commercial butadiene must be calibrated and analyzed. Other impurities were not tested in the cooperative work on this test method.
Note 2: This test method can be used to check for pentadiene-1,4 and other C5s instead of Test Method D1088.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  For specific warning statements, see 6.1 and 9.3.  
1.3.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    7 pages
    English language
    sale 15% off
  • Standard
    7 pages
    English language
    sale 15% off
ASTM
ASTM D2426-23(Test Method)
Standard Test Method for Butadiene Dimer and Styrene in Butadiene Concentrates by Gas Chromatography

SIGNIFICANCE AND USE
4.1 Butadiene dimer and styrene may be present as impurities in commercial butadiene. This test method is suitable for use in internal quality control and in establishing product specifications.
SCOPE
1.1 This test method covers the determination of butadiene dimer (4-vinylcyclohexene-1) and styrene in butadiene concentrates, both recycle and specification grade.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  For specific precautionary statements see Sections 6 and 8.  
1.3.1 The user is advised to obtain LPG safety training for the safe operation of this test method procedure and related activities.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    3 pages
    English language
    sale 15% off
  • Standard
    3 pages
    English language
    sale 15% off
ASTM
ASTM D6805-02(2023)(Practice)
Standard Practice for Infrared (IR) Procedure for Determination of Aromatic/ Aliphatic Ratio of Bituminous Emulsions

SIGNIFICANCE AND USE
5.1 The results of this practice may be used to distinguish tar-based emulsion from an asphalt-based emulsion for specification compliance purposes.
SCOPE
1.1 This practice uses infrared analytical techniques to qualitatively determine in the laboratory a ratio of aromatic absorbance to aliphatic absorbance. This practice may be used to determine if the bitumen in the emulsion is predominantly aromatic or aliphatic in nature.  
1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    5 pages
    English language
    sale 15% off
ASTM
ASTM D5309-22(Specification)
Standard Specification for Cyclohexane 999

ABSTRACT
This specification covers a grade of cyclohexane identified as "cyclohexane 999." The material shall conform to the required purity, benzene content, n-hexane content, methylcyclohexane content, methylcyclopentane content, sulfur content, appearance, color, and distillation range.
SCOPE
1.1 This specification covers a grade of cyclohexane identified as “cyclohexane 999.”  
1.2 The following applies to all specified limits in this standard: for purposes of determining conformance with this standard, an observed value or a calculated value shall be rounded off “to the nearest unit” in the last right-hand digit used in expressing the specification limit, in accordance with the rounding-off method of Practice E29.  
1.3 Consult current OSHA regulations, supplier’s Safety Data Sheets, and local regulations for all materials used in this specification.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    2 pages
    English language
    sale 15% off
  • Technical specification
    2 pages
    English language
    sale 15% off