ASTM A500/A500M-21
(Specification)Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes
Standard Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes
ABSTRACT
This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special shape structural tubing for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes. This tubing shall be produced in both welded and seamless sizes and must have the chemical requirements of carbon, manganese, phosphorus, sulfur, and copper. The steel shall be produced by either open-hearth, basic-oxygen, or electric-furnace melting process. When steels of different grades are sequentially strand cast, the steel producer shall identify the resultant transition material and remove it using an established procedure that positively separates the grades. The tubing shall then be made by a seamless or welding process. Welded tubing shall be made from flat-rolled steel by the electric-resistance-welding process. The longitudinal butt joint of welded tubing shall be welded across its thickness in such a manner that the structural design strength of the tubing section is assured. Tension test and flattening test shall be conducted to the specimens. All tubing shall be inspected at the place of manufacture to ensure conformance to the requirements of this specification and must have a workmanlike finish that is free from defects.
SCOPE
1.1 This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special structural tubular shapes for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes.
1.2 This tubing is produced in both welded and seamless sizes with a periphery of 88 in. [2235 mm] or less, and a specified wall thickness of 1.000 in. [25.4 mm] or less. Grade D requires heat treatment.
Note 1: Products manufactured to this specification may not be suitable for those applications such as dynamically loaded elements in welded structures, etc., where low-temperature notch-toughness properties, which are typically measured by Charpy Impact testing, may be important. There are other ASTM standards that do have CVN requirements and may be more suitable for those applications.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. The inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
1.4 The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes, excluding those in tables and figures, do not contain any mandatory requirements.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A500/A500M −21
Standard Specification for
Cold-Formed Welded and Seamless Carbon Steel Structural
1
Tubing in Rounds and Shapes
This standard is issued under the fixed designationA500/A500M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 Thisspecificationcoverscold-formedweldedandseam-
A370 Test Methods and Definitions for Mechanical Testing
less carbon steel round, square, rectangular, or special struc-
of Steel Products
tural tubular shapes for welded, riveted, or bolted construction
A700 Guide for Packaging, Marking, and Loading Methods
of bridges and buildings, and for general structural purposes.
for Steel Products for Shipment
1.2 This tubing is produced in both welded and seamless
A751 Test Methods and Practices for Chemical Analysis of
sizes with a periphery of 88 in. [2235 mm] or less, and a
Steel Products
specified wall thickness of 1.000 in. [25.4 mm] or less. Grade
A941 TerminologyRelatingtoSteel,StainlessSteel,Related
D requires heat treatment.
Alloys, and Ferroalloys
2.2 Military Standards:
NOTE 1—Products manufactured to this specification may not be
3
MIL-STD-129 Marking for Shipment and Storage
suitable for those applications such as dynamically loaded elements in
welded structures, etc., where low-temperature notch-toughness
MIL-STD-163 Steel Mill Products, Preparation for Ship-
3
properties, which are typically measured by Charpy Impact testing, may
ment and Storage
be important. There are other ASTM standards that do have CVN
2.3 Federal Standards:
requirements and may be more suitable for those applications.
3
Fed. Std. No. 123 Marking for Shipment
1.3 The values stated in either SI units or inch-pound units
Fed.Std.No.183 ContinuousIdentificationMarkingofIron
3
are to be regarded separately as standard. Within the text, the
and Steel Products
SI units are shown in brackets. The values stated in each
2.4 AIAG Standard:
system may not be exact equivalents; therefore, each system
4
B-1 Bar Code Symbology Standard
shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the
3. Terminology
standard. The inch-pound units shall apply unless the “M”
3.1 Definitions—For definitions of terms used in this
designation of this specification is specified in the order.
specification, refer to Terminology A941.
1.4 The text of this specification contains notes and foot-
notes that provide explanatory material. Such notes and 4. Ordering Information
footnotes, excluding those in tables and figures, do not contain
4.1 Orders for material under this specification shall contain
any mandatory requirements.
information concerning as many of the following items as are
required to describe the desired material adequately:
1.5 This international standard was developed in accor-
4.1.1 Quantity (feet [metres] or number of lengths),
dance with internationally recognized principles on standard-
4.1.2 Name of material (cold-formed tubing),
ization established in the Decision on Principles for the
4.1.3 Method of manufacture (seamless or welded),
Development of International Standards, Guides and Recom-
4.1.4 Grade (B, C, or D),
mendations issued by the World Trade Organization Technical
Barriers to Trade (TBT) Committee.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Standards volume information, refer to the standard’s Document Summary page on
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee the ASTM website.
3
A01.09 on Carbon Steel Tubular Products. AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
Current edition approved Jan. 1, 2021. Published January 2021. Originally Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
4
approved in 1964. Last previous edition approved in 2020 as A500/A500M – 20. Available fromAutomotive IndustryAction Group (AIAG), 26200 Lahser Rd.,
DOI: 10.1520/A0500_A0500M-21. Suite 200, Southfield, MI 48033, http://www.aiag.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A500/A500M−21
4.1.5 Size (outside diameter and wall thickness for round 8. Product Analysis
tubing, and outside dimensions and wall thickness for square
8.1 The tubing shal
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A500/A500M − 20 A500/A500M − 21
Standard Specification for
Cold-Formed Welded and Seamless Carbon Steel Structural
1
Tubing in Rounds and Shapes
This standard is issued under the fixed designation A500/A500M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers cold-formed welded and seamless carbon steel round, square, rectangular, or special shape structural
tubing tubular shapes for welded, riveted, or bolted construction of bridges and buildings, and for general structural purposes.
1.2 This tubing is produced in both welded and seamless sizes with a periphery of 88 in. [2235 mm] or less, and a specified wall
thickness of 1.000 in. [25.4 mm] or less. Grade D requires heat treatment.
NOTE 1—Products manufactured to this specification may not be suitable for those applications such as dynamically loaded elements in welded structures,
etc., where low-temperature notch-toughness properties properties, which are typically measured by Charpy Impact testing, may be important. There are
other ASTM standards that do have CVN requirements and may be more suitable for those applications.
1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard. The
inch-pound units shall apply unless the “M” designation of this specification is specified in the order.
1.4 The text of this specification contains notes and footnotes that provide explanatory material. Such notes and footnotes,
excluding those in tables and figures, do not contain any mandatory requirements.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A370 Test Methods and Definitions for Mechanical Testing of Steel Products
A700 Guide for Packaging, Marking, and Loading Methods for Steel Products for Shipment
A751 Test Methods and Practices for Chemical Analysis of Steel Products
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee A01.09
on Carbon Steel Tubular Products.
Current edition approved May 15, 2020Jan. 1, 2021. Published June 2020January 2021. Originally approved in 1964. Last previous edition approved in 20182020 as
A500/A500M – 18.A500/A500M – 20. DOI: 10.1520/A0500_A0500M-20.10.1520/A0500_A0500M-21.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
A500/A500M − 21
2.2 Military Standards:
3
MIL-STD-129 Marking for Shipment and Storage
3
MIL-STD-163 Steel Mill Products, Preparation for Shipment and Storage
2.3 Federal Standards:
3
Fed. Std. No. 123 Marking for Shipment
3
Fed. Std. No. 183 Continuous Identification Marking of Iron and Steel Products
2.4 AIAG Standard:
4
B-1 Bar Code Symbology Standard
3. Terminology
3.1 Definitions—For definitions of terms used in this specification, refer to Terminology A941.
4. Ordering Information
4.1 Orders for material under this specification shall contain information concerning as many of the following items as are required
to describe the desired material adequately:
4.1.1 Quantity (feet [metres] or number of lengths),
4.1.2 Name of material (cold-formed tubing),
4.1.3 Method of manufacture (seamless or welded),
4.1.4 Grade (A, B, (B, C, or D),
4.1.5 Si
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.