iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D3737-07

(Practice)

Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

SCOPE
1.1 This practice covers the procedures for establishing allowable properties for structural glued laminated timber. Included are the allowable stresses for bending, tension and compression parallel to the grain, horizontal shear, compression perpendicular to the grain, and radial tension and compression in curved members. Also included are modulus of elasticity and modulus of rigidity.
1.2 This practice is limited to the calculation of allowable properties subject to the given procedures for the selection and arrangement of grades of lumber of the species considered.
1.3 Requirements for production, inspection and certification are not included, but in order to justify the allowable properties developed using procedures in this practice, manufacturers must conform to recognized manufacturing standards. Refer to ANSI/AITC A190.1 and CSA 0122.
1.4 The values stated in inch-pound units are to be regarded as standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
31-Mar-2007
ICS
79.060.01 - Wood-based panels in general
Technical Committee
D07 - Wood
Drafting Committee
D07.02 - Lumber and Engineered Wood Products
Current Stage
Ref Project

Relations

Replaces
ASTM D3737-06 - Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
Effective Date
01-Apr-2007
Replaced By
ASTM D3737-08 - Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
Effective Date
15-Apr-2008
Referred By
ASTM D7199-20 - Standard Practice for Establishing Characteristic Values for Reinforced Glued Laminated Timber (Glulam) Beams Using Mechanics-Based Models
Effective Date
01-Apr-2007
Referred By
ASTM D2915-17(2022) - Standard Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products
Effective Date
01-Apr-2007
Referred By
ASTM D198-22a - Standard Test Methods of Static Tests of Lumber in Structural Sizes
Effective Date
01-Apr-2007
Referred By
ASTM D7147-21 - Standard Specification for Testing and Establishing Allowable Loads of Joist Hangers
Effective Date
01-Apr-2007
Referred By
ASTM D5457-23 - Standard Specification for Computing Reference Resistance of Wood-Based Materials and Structural Connections for Load and Resistance Factor Design
Effective Date
01-Apr-2007
Referred By
ASTM D6570-18a(2023)e1 - Standard Practice for Assigning Allowable Properties for Mechanically Graded Lumber
Effective Date
01-Apr-2007
Referred By
ASTM D7341-21 - Standard Practice for Establishing Characteristic Values for Flexural Properties of Structural Glued Laminated Timber by Full-Scale Testing
Effective Date
01-Apr-2007

Buy Standard

ASTM D3737-07 - Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)ASTM D3737-07 - Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
PreviousNext
Standard
ASTM D3737-07 - Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
English language
28 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D 3737 – 07
Standard Practice for
Establishing Allowable Properties for Structural Glued
1
Laminated Timber (Glulam)
This standard is issued under the fixed designation D3737; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Wood-Based Materials
D2555 Practice for Establishing Clear Wood Strength Val-
1.1 This practice covers the procedures for establishing
ues
allowable properties for structural glued laminated timber.
D2915 Practice for Evaluating Allowable Properties for
Included are the allowable stresses for bending, tension and
Grades of Structural Lumber
compression parallel to the grain, horizontal shear, compres-
D4761 Test Methods for Mechanical Properties of Lumber
sion perpendicular to the grain, and radial tension and com-
and Wood-Base Structural Material
pression in curved members. Also included are modulus of
D5456 Specification for Evaluation of Structural Compos-
elasticity and modulus of rigidity.
ite Lumber Products
1.2 This practice is limited to the calculation of allowable
D6570 Practice for Assigning Allowable Properties for
properties subject to the given procedures for the selection and
Mechanically Graded Lumber
arrangement of grades of lumber of the species considered.
E105 Practice for Probability Sampling Of Materials
1.3 Requirements for production, inspection and certifica-
2.2 Other Standards:
tion are not included, but in order to justify the allowable
3
ANSI/AITC A190.1 Structural Glued Laminated Timber
properties developed using procedures in this practice, manu-
ANSI/AF&PA National Design Specification for Wood
facturersmustconformtorecognizedmanufacturingstandards.
4
Construction
Refer to ANSI/AITC A190.1 and CSA0122.
5
CSA 0122 Structural Glued Laminated Timber
1.4 Thevaluesstatedininch-poundunitsaretoberegarded
as standard.
3. Terminology
1.5 This standard does not purport to address all of the
3.1 Definitions:
safety concerns, if any, associated with its use. It is the
3.1.1 Alternative lumber—laminated veneer lumber (LVL),
responsibility of the user of this standard to establish appro-
laminated strand lumber (LSL), oriented strand lumber (OSL),
priate safety and health practices and determine the applica-
or parallel strand lumber (PSL) meeting the requirements of
bility of regulatory limitations prior to use.
Specification D5456, or solid-sawn lumber that is produced
2. Referenced Documents according to Practice D6570 and the grading rules of the
2 applicable grading or inspection agency.
2.1 ASTM Standards:
3.1.2 E-rated lumber—lumber graded for use in manufac-
D9 Terminology Relating to Wood and Wood-Based Prod-
turing structural glued laminated timber by nondestructive
ucts
measurement of a modulus of elasticity (E) and by visual
D198 Test Methods of StaticTests of Lumber in Structural
inspection in accordance with the grading rules of the appli-
Sizes
cable grading or inspection agency.
D245 Practice for Establishing Structural Grades and Re-
3.1.3 glulam—a term used to denote structural glued lami-
lated Allowable Properties for Visually Graded Lumber
nated timber, which is a product made from suitably selected
D2395 Test Methods for Specific Gravity of Wood and
andpreparedpiecesofwoodbondedtogetherwithanadhesive
either in a straight or curved form with the grain of all pieces
1
This practice is under the jurisdiction ofASTM Committee D07 on Wood and essentially parallel to the longitudinal axis of the member.
is the direct responsibility of Subcommittee D07.02 on Lumber and Engineered
Wood Products.
3
Current edition approved April 1, 2007. Published April 2007. Originally Available from theAmerican Institute ofTimber Construction, 7012 S. Revere
approved in 1978. Last previous edition approved in 2006 as D3737–06. Parkway Suite 140, Englewood, CO 80112.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or Available from American Forest and Paper Association (AF&PA), 1111 19th
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM St., NW, Suite 800, Washington, DC 20036.
5
Standards volume information, refer to the standard’s Document Summary page on Available from Canadian Standards Association (CSA), 178 Rexdale Blvd.,
the ASTM website. Toronto, ON Canada M9W1R3.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
D3737–07
3.1.4 horizontally laminated timber—amemberdesignedto 4.1.2 Lumber is permitted to be joined end to end with
resist bending loads applied perpendicul
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D3737-18(2023)e1(Practice)
Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)

ABSTRACT
This practice details the standard procedures for establishing the allowable properties for structural glued laminated timber (glulam). Allowable properties include: stress indexes; stress modification factors associated with slop of grain; stresses for bending, tension and compression parallel to the grain; horizontal shear; compression perpendicular to the grain; radial tension and compression stresses in curved members; grade adjustment factors; modulus of elasticity; and modulus of rigidity. This practice is limited to the calculation of allowable properties subject to the given procedures for the selection and arrangement of grades of lumber of the species considered. It does not cover the requirements for production, inspection and certification, but in order to justify the allowable properties developed using procedures in this practice, manufacturers must conform to recognized manufacturing standards.
SCOPE
1.1 This practice covers the procedures for establishing allowable properties for structural glued laminated timber. Included are the allowable stresses for bending, tension and compression parallel to the grain, horizontal shear, compression perpendicular to the grain, and radial tension and compression in curved members. Also included are modulus of elasticity and modulus of rigidity.  
1.2 This practice is limited to the calculation of allowable properties subject to the given procedures for the selection and arrangement of grades of lumber of the species considered.  
1.3 Requirements for production, inspection and certification are not included, but in order to justify the allowable properties developed using procedures in this practice, manufacturers must conform to recognized manufacturing standards. Refer to ANSI A190.1 and CSA O122.  
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in SI units are mathematical conversions that are provided for information only and are not considered standard.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    41 pages
    English language
    sale 15% off
ASTM
ASTM D6643-01(2023)(Test Method)
Standard Test Method for Testing Wood-Base Panel Corner Impact Resistance

SIGNIFICANCE AND USE
5.1 This test method determines the corner impact damage that could be used to measure the relative corner impact resistance.
SCOPE
1.1 This test method shall be used to measure the relative corner impact resistance and other damage that may occur during the rough handling of wood-base panels or composite materials. This test method is suitable for all wood-base panels such as plywood, oriented strand board, hardboard, particleboard and medium density fiberboard as well as other composite panel products.  
1.2 This test method covers determination and evaluation of the effects of panels being dropped from various heights with a predetermined amount of dead load and angle of impact to simulate an equivalent field application.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1554-10(2023)(Terminology)
Standard Terminology Relating to Wood-Base Fiber and Particle Panel Materials

SCOPE
1.1 This terminology standard covers a repository of terms and classifications essential for the business of Subcommittee D07.03.  
1.2 Terms and classifications for inclusion in this terminology standard when needed for general use in the conduct of the standards over which Subcommittee D07.03 has jurisdiction.  
1.3 The terms in this standard pertain to cellulosic boards or panel products derived from wood and the woody tissue of such plants as bagasse, flax, and straw. They fall into two general groups: (1) those manufactured from lignocellulosic fibers and fiber bundles where in manufacture the interfelting of the fibers and a natural bond are characteristics, and (2) those boards manufactured from a wide range in size and shape of particles ranging from fine elements approaching fibers in size to large flakes which are blended with synthetic resin adhesive and consolidated into boards characterized by the resin bond and usually known as resin-bonded particleboards or more commonly as particleboards.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM D1666-22(Test Method)
Standard Test Methods for Conducting Machining Tests of Wood and Wood-Base Panel Materials

SIGNIFICANCE AND USE
4.1 Machining tests are made to determine the working qualities and characteristics of different species of wood and of different wood-based panel materials under a variety of machine operations such as are encountered in commercial manufacturing practice. The tests provide a systematic basis for comparing the behavior of different products with respect to woodworking machine operations and of evaluating their potential suitability for certain uses where these properties are of prime importance.
SCOPE
1.1 These test methods cover procedures for planing, routing/shaping, turning, mortising, boring, and sanding, all of which are common wood-working operations used in the manufacture of wood products. These tests apply, in different degrees, to two general classes of materials:  
1.1.1 Wood in the form of lumber, and  
1.1.2 Wood-base panel materials such as plywood and wood-base fiber and particle panels.  
1.2 Because of the importance of planing, some of the variables that affect the results of this operation are explored with a view to determining optimum conditions. In most of the other tests, however, it is necessary to limit the work to one set of fairly typical commercial conditions in which all the different woods are treated alike.  
1.3 Several factors enter into any complete appraisal of the machining properties of a given wood or wood-base panel. Quality of finished surface is recommended as the basis for evaluation of machining properties. Rate of dulling of cutting tools and power consumed in cutting are also important considerations but are beyond the scope of these test methods.  
1.4 Although the methods presented include the results of progressive developments in the evaluation of machining properties, further improvements are anticipated. For example, by present procedures, quality of the finished surface is evaluated by visual inspection, but as new mechanical or physical techniques become available that will afford improved precision of evaluation, they should be employed.  
1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.7 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    17 pages
    English language
    sale 15% off
  • Standard
    17 pages
    English language
    sale 15% off
ASTM
ASTM D2395-17(2022)(Test Method)
Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials

SIGNIFICANCE AND USE
5.1 Density and specific gravity are cornerstone terms that help define many useful properties of wood and wood-based materials. These terms designate concepts that have distinct definitions though they relate to the same characteristic (mass in a unit volume). Generally, in the US and Canada, density of wood is measured in terms of specific gravity, or relative density. In the wood-based composites industry and internationally the term density is often preferred.  
5.2 The basic density and basic specific gravity of wood are used in the forestry industry for calculating the oven-dry weight of wood fiber contained in a known wood volume of various wood species. Thus, it serves as an indicator of the amount of wood pulp that could be produced, the workability of the material or its shipping weight. This information is referenced in various resources, including Wood Handbook.5 Note that specific gravity varies within a tree, between trees, and between species. Since the specific gravity of wood cell wall substance is practically constant for all species (approximately 1.53), it is apparent that individual specific gravity value is indicative of the amount of wood cell wall substance present. It affords a rapid and valuable test method for selection of wood for specific uses. In US and Canadian building codes, the oven-dry specific gravity is correlated to various strength characteristics of wood products (for example, compression perpendicular to grain, shear strength and fastener holding capacity).  
5.3 It is often desirable to know the density or specific gravity of a living tree, a structural member already in place, a log cross section, a segment of a research element, or the earlywood or latewood layer. Therefore, it is possible that specimens will be large or small, regular or irregular in shape, and at a variety of moisture contents. These test methods give procedures that include all of these variables and provides for calculation of density and specific gr...
SCOPE
1.1 These test methods cover the determination of the density and specific gravity (relative density) of wood and wood-based materials to generally desired degrees of accuracy and for specimens of different sizes, shapes, and moisture content conditions. The test method title is indicative of the procedures used or the specific area of use.    
Section  
Test Method A—Volume by Measurement  
8  
Test Method B—Volume by Water Immersion  
9  
Test Method C—Flotation Tube  
10  
Test Method D—Forstner Bit  
11  
Test Method E—Increment Core  
12  
Test Method F—Chips  
13  
Test Method G—Full-Size Members  
14  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    13 pages
    English language
    sale 15% off
ASTM
ASTM D7033-22(Practice)
Standard Practice for Establishing Design Capacities for Oriented Strand Board (OSB) Wood-Based Structural-Use Panels

SIGNIFICANCE AND USE
4.1 The procedures described in this practice are intended to be used to establish design capacity (both strength and stiffness) values based on testing of OSB that, at a minimum, satisfies the relevant performance requirements of PS 2.  
4.2 Review and reassessment of values derived from this practice shall be conducted on a periodic basis. If a change is found to be significant, retesting or reevaluation, or both, in accordance with the procedures of this practice shall be considered.
SCOPE
1.1 This practice covers the basis for code recognition of design capacities for OSB structural-use panels. Procedures are provided to establish or re-evaluate design capacities for OSB structural-use panels in flatwise and axial applications. Design capacities for OSB structural-use panels in edgewise applications, such as rim board, are outside the scope of this standard. Procedures for sampling and testing are also provided. Design values stated as capacity per unit dimension are to be regarded as standard. Design capacities developed in accordance with this practice are applicable to panels intended for use in dry in-service conditions.
Note 1: This practice is based on ICC-ES Acceptance Criteria AC-182. Relative to the scope of AC-182, this practice is limited to OSB panels.
Note 2: While this practice makes reference to PS 2, this practice applies similarly to products certified to other standards such as CAN/CSA O325.
Note 3: OSB produced under PS 2 is rated with the “Exposure 1” bond classification. Exposure 1 panels covered by PS 2 are intended for dry use applications where the in-service equilibrium moisture content conditions are expected to be less than 16 %. Exposure 1 panels are intended to resist the effects of moisture due to construction delays, or other conditions of similar severity. Guidelines on use of OSB are available from manufacturers and qualified agencies.
Note 4: PS 2-10 replaced the use of nominal thicknesses with a classification term known as Performance Category, which is defined in PS 2 as “A panel designation related to the panel thickness range that is linked to the nominal panel thickness designations used in the International Building Code (IBC) and International Residential Code (IRC).” Therefore, the PS 2 Performance Category should be considered equivalent to the term “nominal thickness” used within this standard.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    9 pages
    English language
    sale 15% off
  • Standard
    9 pages
    English language
    sale 15% off
ASTM
ASTM D7989-21(Practice)
Standard Practice for Demonstrating Equivalent In-Plane Lateral Seismic Performance to Wood-Frame Shear Walls Sheathed with Wood Structural Panels

SIGNIFICANCE AND USE
5.1 This practice documents cyclic performance benchmarks for shear walls constructed with wood structural panel (WSP) sheathing attached to dimension lumber framing using common or galvanized box nails as defined in 3.2.8.  
5.2 Procedures described in this practice provide a method to evaluate an alternative shear wall system’s SEPs to demonstrate equivalent in-plane lateral seismic performance to the reference shear wall system.  
5.3 The procedures described in this practice do not address all factors to be considered for recognition of an alternative shear wall system. Such factors, as described in 1.4, vary by the end-use application and shall be addressed outside the scope of this standard through an evaluation of the acceptability of the alternative shear wall system in accordance with requirements of building codes and standards, as applicable.
SCOPE
1.1 This practice establishes a method for alternative shear wall systems to compare seismic equivalency parameters (SEP) derived from cyclic in-plane racking tests to performance targets derived from tests of light-frame shear walls constructed with wood structural panel (WSP) sheathing attached to dimension lumber framing using nails.  
1.2 This practice considers only the performance of shear walls subject to cyclic lateral loading, parallel to the plane of the shear wall. Design of walls with openings and performance for other wall functions, such as out-of-plane bending, combined shear and uplift, and so forth are not considered.  
1.3 This practice is applicable only to shear walls where all vertical-load-supporting elements are intact at the end of the in-plane lateral load test and remain capable of supporting gravity loads. Wall assemblies whose vertical-load-supporting elements buckle or otherwise become incapable of supporting gravity loads during the lateral load test are outside the scope of this practice. In addition, for bearing wall systems, this practice assumes that the shear wall system under evaluation has documented design procedures to ensure that vertical-load-supporting elements have adequate resistance to the combined effect of compression loads caused by overturning and gravity loads.  
1.4 This practice does not address height limitations, detailing requirements, wall openings, derivation of design values for strength and stiffness, or other requirements and limitations that may be necessary for an alternative shear wall system. These requirements shall be provided elsewhere, such as by a suitable product standard for the alternative shear wall system.  
1.5 This practice assumes that the stiffness or deformation of the alternative shear wall system can be estimated, and that design loads within a structure will be distributed among seismically equivalent wall systems based on their relative stiffness.  
1.6 This practice is not intended to preclude other rational means of evaluating seismic performance.  
1.7 This practice assumes that the alternative shear wall system may be used alone or in combination with wood-frame shear walls sheathed with wood structural panels.  
1.8 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT)...

  • Standard
    10 pages
    English language
    sale 15% off
  • Standard
    10 pages
    English language
    sale 15% off
ASTM
ASTM D4933-16(2021)(Guide)
Standard Guide for Moisture Conditioning of Wood and Wood-Based Materials

SIGNIFICANCE AND USE
4.1 Many physical and mechanical properties of wood and wood-based materials change in response to the environmental equilibrium moisture content, and any comparison of these properties must take moisture content into account. A consistent base for comparison among different test samples and different laboratories is necessary. Shrinkage and dimensional change in particular are dependent on moisture content, and tests involving their measurement must be conducted with good equilibrium moisture content control. Conditioning can also be important in industrial settings where there are optimum moisture content levels for many products and processes, and conformance to these levels can reduce losses in quality and yield.
SCOPE
1.1 This guide covers standard procedures for conditioning and equilibrating wood and wood-based materials to constant moisture content. The procedures apply to solid wood, wood-based fiber and particulate materials and panels, and wood products containing adhesives. They are intended for use in research and development activities, testing laboratories, quality control, and for all other classes of producers and users. This guide includes background material on the importance of moisture content control, important definitions and technical data, possible types of apparatus, procedures, and the importance of conditioning time. Users should recognize that the necessary degree of precision and bias varies with the intentions of the users. Some research and testing, for example, might require very close control of moisture content, whereas control in an industrial storage facility might not require such close control. This guide offers procedures that include these different requirements.  
1.2 The values stated in SI units are to be regarded as standard. The values of temperature in degrees Fahrenheit given in Table X1.2 are mathematical conversions that are provided for information only and are not considered standard.  
1.3 The following safety hazards caveat pertains only to the procedure section, Section 6, of this guide. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    8 pages
    English language
    sale 15% off
ASTM
ASTM D7612-21(Practice)
Standard Practice for Categorizing Wood and Wood-Based Products According to Their Fiber Sources

SIGNIFICANCE AND USE
5.1 Voluntary forest certification systems have become an important factor in promoting sustainable forest management. The standards in use are highly variable, however. Even within a family of standards with a common label there is the potential for wide variations in practices. This prevents producers and consumers from using a certification label to characterize products according to a specific set of qualities or values. This practice creates a framework to differentiate products based on a set of qualities and values identified as important in the market for wood products. (A) See Appendix X3 for discussion of additional concepts related to sub-categorization of certified sources.(B) For the purposes of categorizing products under this practice, distributors and retailers can rely on “on-product” labels for chain of custody or a certified procurement system if they are not engaged in significant value-added processing or remanufacture. In lieu of an on‐product label, a certificate of compliance indicating conformance with the applicable chain of custody or certified procurement system is permitted.  
5.2 This practice is intended to be used by producers, distributors, retailers, or consumers who wish to understand where a product fits within three categories. At a minimum, the user will need to know the geographic origin of the wood going into a product and whether it is labeled or otherwise certified to a procurement system or chain of custody based on a voluntary forest management or certification standard. Producers who want to use this practice must be able to identify the geographic origin of the wood to at least the level needed to support the claims to consumers associated with a given category and described in 6.1.
SCOPE
1.1 This practice sets forth minimum criteria and evaluation requirements for products employing the use of different systems to trace wood fiber to sources operating under different forest management or forest certification systems.  
1.2 The purpose of this practice is to provide wood products manufacturers, distributors, and retailers with a system to provide clear, objective information to communicate to consumers regarding product conformance to different wood fiber tracing systems within specific forest management or forest certification programs. It provides a structure that segregates the different types of labels and tracing systems in use among major forest certification standards and other voluntary and regulatory standards governing the production of forest products.
Note 1: The principles in this practice apply internationally, provided that the required information is available to support categorization. For example, products certified to the globally recognized forest certification standards will meet the “Certified Sources” category regardless of their origin, and documented risk assessments (noted in Appendix X5) provide the basis upon which raw materials sourced from Canada and the United States can be deemed to meet the “Legal Sources” category. To categorize raw materials sourced outside of Canada and the United States as “Legal Sources,” it is recommended that the adopting entity develop supplemental provisions to address country-specific issues as needed.  
1.2.1 This practice provides an objective basis to differentiate among:
1.2.1.1 Non-controversial (that is, legal) sources of forest products,
1.2.1.2 Responsible sources of forest products (that is, non-controversial sources together with certified procurement systems or from forests managed using responsible practices), and
1.2.1.3 Certified sources of forest products (that is, non-controversial sources together with certified chain of custody).  
1.2.2 This practice is intended to provide a framework to help wood product vendors identify the competent and reliable evidence needed to substantiate product claims as required by the U.S. Federal Trade Commission’s Guides for ...

  • Standard
    11 pages
    English language
    sale 15% off
  • Standard
    11 pages
    English language
    sale 15% off
ASTM
ASTM D1166-21(Test Method)
Standard Test Method for Methoxyl Groups in Wood and Related Materials

SIGNIFICANCE AND USE
3.1 Most of the methoxyl in wood is attributable to the lignin. This test method is used extensively in the study of lignin.
SCOPE
1.1 This test method covers the determination of methoxyl groups in wood and related materials (1-7).2 The test method is applicable to milled wood or sawdust, or by suitable adjustment in size of the test specimen, to fractions isolated from wood and lignin.  
1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 6.  
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off