iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
ASTM

ASTM D6464-03ae1

(Specification)

Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing

Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing

ABSTRACT
This specification establishes minimum performance requirements for determining strength, aging, and working properties of expandable foam adhesives intended for bonding back surfaces of gypsum wallboards of all thicknesses to wood framing. Minimum physical and performance requirements are specified for all measured properties of adhesives and adhesive bonds. Shear strength, tensile strength, adhesive open assembly time determination, substrate wet-out by adhesive, accelerated adhesive aging, freeze-thaw stability, suitability of a laminating adhesive for vinyl-covered wallboard, suitability for stain resistance for vinyl-covered wallboard, and gap filling tests shall be performed to conform to the specified requirements.
SCOPE
1.1 This specification establishes minimum performance requirements for determining strength, aging, and working properties of expandable foam adhesives intended for bonding back surfaces of gypsum wallboards of all thicknesses to wood framing. Minimum physical and performance requirements are specified for all measured properties of adhesives and adhesive bonds.
1.2 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are for information only.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

Status
Historical
Publication Date
09-Aug-2003
ICS
49.025.50 - Adhesives
Technical Committee
D14 - Adhesives
Drafting Committee
D14.70 - Construction Adhesives
Current Stage
Ref Project

Relations

Replaces
ASTM D6464-03a - Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing
Effective Date
10-Aug-2003
Replaced By
ASTM D6464-03a(2009)e1 - Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing
Effective Date
01-Nov-2009
Referred By
ASTM C1852-20 - Standard Guide for Product Selection/Delivery Systems for Aerosol Foam Sealants and Adhesives
Effective Date
10-Aug-2003

Buy Standard

ASTM D6464-03ae1 - Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood FramingASTM D6464-03ae1 - Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing
PreviousNext
Technical specification
ASTM D6464-03ae1 - Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing
English language
8 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information.
´1
Designation: D6464 – 03a
Standard Specification for
Expandable Foam Adhesives for Fastening Gypsum
1
Wallboard to Wood Framing
This standard is issued under the fixed designation D6464; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1
´ NOTE—Editorial changes were made throughout in May 2006.
1. Scope* 3. Terminology
1.1 This specification establishes minimum performance 3.1 Definitions—Many terms in this specification are de-
requirements for determining strength, aging, and working fined in Terminology D907.
properties of expandable foam adhesives intended for bonding 3.2 Definitions of Terms Specific to This Standard:
back surfaces of gypsum wallboards of all thicknesses to wood 3.2.1 expandable foam adhesive, n—any polymer that ex-
framing. Minimum physical and performance requirements are pands during delivery or cure to fill the space between
specified for all measured properties of adhesives and adhesive substrates.
bonds.
4. Significance and Use
1.2 The values stated in inch-pound units are to be regarded
as the standard. The SI units given in parentheses are for 4.1 This specification applies to expandable foam adhesives
used to bond the back surface of gypsum wallboard to
information only.
1.3 This standard does not purport to address all of the Douglas-fir dimensional lumber or other lumber species of
equivalent bonding qualities capable of meeting the test
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro- requirements.
4.2 The specification establishes the minimum strength
priate safety and health practices and determine the applica-
bility of regulatory limitations prior to use. requirements of the bond for the selected assembly materials.
4.3 The adhesive is not considered a substitute for mechani-
2. Referenced Documents
cal fasteners. Fasteners will be required to restrict expansion of
2
2.1 ASTM Standards: the foam adhesive while it cures. The recommended fastening
C1396/C1396M Specification for Gypsum Board schedulemustappearinthemanufacturer’sapplicationinstruc-
D905 Test Method for Strength Properties of Adhesive tions.
Bonds in Shear by Compression Loading 4.4 The tests are suitable for product performance certifica-
D907 Terminology of Adhesives tion and quality control programs, and can be useful to the
E4 Practices for Force Verification of Testing Machines general public, adhesive manufacturers, distributors, specifiers,
E177 Practice for Use of the Terms Precision and Bias in architects,contractors,testinglaboratoriesandotherbusinesses
ASTM Test Methods and professionals.
4.5 The results do not include all possible conditions, which
may occur during final assembly, but indicate a set of perfor-
1
This specification is under the jurisdiction of ASTM Committee D14 on
mance characteristics for laboratory controlled bonding vari-
Adhesives and is the direct responsibility of Subcommittee D14.70 on Construction
ables.
Adhesives.
Current edition approved Aug. 10, 2003. Published September 2003. Originally
approved in 1999. Last previous edition approved in 2003 as D6464 - 03. DOI:
5. Adhesive Physical Property Requirements
10.1520/D6464-03AE01.
2 5.1 Open Assembly Time—These adhesives have a distinct
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM open assembly time and this time must be agreed upon by the
Standards volume information, refer to the standard’s Document Summary page on
user and the manufacturer.
the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
´1
D6464 – 03a
5.2 Storage Life—The adhesive shall remain serviceable
and meet all the requirements of this specification for not less
than six months after delivery, when stored in original un-
opened containers at temperatures ranging from 40 to 85°F
(4 to 30°C).
6. Adhesive Properties and Performance
6.1 The adhesives shall conform to the requirements sum-
marized in Table 1.
7. Materials and Apparatus for Conducting Tests
7.1 Adhesives—The adhesive shall be an expandable foam
adhesive.
1
7.2 Gypsum Wallboard— ⁄2 in. (12.7 mm) thick, complying
with Specification C1396/C1396M; the dimensions are speci-
fied in each test.
3 23
7.3 Plywood— ⁄4 or ⁄32 in. (19.0 or 18.3 mm)-thick U.S.
Product Standard PS-1-95 grade marked stamped, commercial
FIG. 1 Tensile Strength
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

ASTM
ASTM D6412/D6412M-99(2020)(Specification)
Standard Specification for Epoxy (Flexible) Adhesive For Bonding Metallic And Nonmetallic Materials

ABSTRACT
The specification covers a two-part modified epoxy paste adhesive for bonding metallic and nonmetallic materials. The adhesive should be suitable for forming bonds that can withstand environmental exposure to a certain temperature range when exposed to an expected combination of stress, temperature, and relative humidity to be encountered in service. Two types of adhesive shall be classified according to composition. Type I which consists of two-part kits of liquid base and modified amide liquid accelerator. Type I is further subdivided into two grades: Grade 1 with low viscosity and Grade 2 with high viscosity. The other classification is Type II which consists of premixed, frozen, Type I, Grade 1 or Type I, Grade 2. Different tests shall be conducted in order to determine the following mechanical properties of the adhesives: room-temperature shear, high-temperature shear, low-temperature shear, room-temperature Shore D hardness, room-temperature T-peel, and outgassing characteristics such as total mass loss and vacuum condensable material.
SCOPE
1.1 The specification covers a two-part modified epoxy paste adhesive for bonding metallic and nonmetallic materials. The adhesive should be suitable for forming bonds that can withstand environmental exposure to temperatures from –184 to 82 °C [–300 to 180 °F] when exposed to an expected combination of stress, temperature, and relative humidity to be encountered in service.
Note 1: When coordinated through the Department of Defense (DoD) and the National Aeronautics and Space Administration (NASA), this practice will be a direct replacement of MIL-A-82720 (OS), MIS-26872, and MSFC-SPEC-2037.  
1.2 The values stated in SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.3 The following precautionary statement pertains to the test method portion only, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6464-03a(2017)(Specification)
Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing

ABSTRACT
This specification establishes minimum performance requirements for determining strength, aging, and working properties of expandable foam adhesives intended for bonding back surfaces of gypsum wallboards of all thicknesses to wood framing. Minimum physical and performance requirements are specified for all measured properties of adhesives and adhesive bonds. Shear strength, tensile strength, adhesive open assembly time determination, substrate wet-out by adhesive, accelerated adhesive aging, freeze-thaw stability, suitability of a laminating adhesive for vinyl-covered wallboard, suitability for stain resistance for vinyl-covered wallboard, and gap filling tests shall be performed to conform to the specified requirements.
SCOPE
1.1 This specification establishes minimum performance requirements for determining strength, aging, and working properties of expandable foam adhesives intended for bonding back surfaces of gypsum wallboards of all thicknesses to wood framing. Minimum physical and performance requirements are specified for all measured properties of adhesives and adhesive bonds.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM D6465-99(2016)(Guide)
Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants

SIGNIFICANCE AND USE
5.1 The guide is to be used by anyone developing bonding or sealing requirements for specifications for manufacturing, maintenance or overhaul. This guide has been designed to be application specific for each bonding or sealing application, and allows the design engineer to rest assured that the product(s) or process(es) selected by the industrial or manufacturing engineer will be compatible with both the part material and the subsequent processes, such as adherend/substrate cleaning and preparation. It allows the industrial or manufacturing engineer to customize the selection of the adhesive or sealant product based on the materials of the parts being bonded or sealed, the conditions required for the subsequent process(es), environmental, cost, and health and safety concerns.
SCOPE
1.1 This guide is intended to assist design engineers, manufacturing/industrial engineers, and production managers in selecting the best-fit adhesive/sealant or bonding/sealing process. The guide takes into account environmental pollution prevention and occupational health and safety factors in a selection process.  
1.2 This guide is not to be considered as a database of acceptable materials. It will guide the engineers and managers through the adhesive/sealant material selection process, calling for engineers to customize their selection based on the bonding or sealing performance requirements for the specified application. A comprehensive selection process will allow for the establishment of a more efficient production process, and may eliminate unnecessary process steps. A total life cycle cost analysis or performance/cost of implementation study is recommended to compare the available alternatives.  
1.3 This guide is for aerospace and general purpose operations. It is not intended to be used for automotive, carpet, construction, electronics, medical/dental, optical, or structural and nonstructural wood applications. Note that this guide is not specifically for these applications, but the general methodology may be used in the selection process for these applications.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM F942-18(2023)e1(Guide)
Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures

SIGNIFICANCE AND USE
3.1 This guide is intended for use by material suppliers, aircraft transparent enclosure fabricators, airframe manufacturers, government agencies, and others that may become involved in the testing of transparent interlayer materials. These test methods provide data on both individual interlayer materials and material combinations commonly used in the fabrication of aerospace transparent enclosures and provide a means of evaluating the performance of one interlayer material against another.  
3.2 Primary characteristics and their long-term stability are critical to the performance of an interlayer material. Basic tests define the as-manufactured material characteristics of the interlayer material. Aging procedures provide for representative exposure to environments that induce changes in material characteristics. Tests performed before and after ageing exposure provide a means of estimating the potential useable life-span of an interlayer material or to compare the durability of one interlayer material with another.  
3.3 When employing these test methods for the comparison of interlayer materials after exposure to selected environmental conditions, the user shall be aware that many factors influencing degradation due to weathering vary from one location and exposure period to another location and exposure period. For direct weathering comparisons, the interlayer materials to be compared shall be subjected to the exposure and have the tests performed at the same time. It is emphasized that the test values obtained under these simultaneously applied conditions are for comparative use and their use as design characteristics shall be made with caution.  
3.4 The test methods listed include those considered critical to the performance of aircraft transparent enclosures. The user is advised to use the latest revision of any test method.
SCOPE
1.1 This guide summarizes the standard test methods available for determining physical and mechanical characteristics of interlayer materials used in multi-ply aerospace transparent enclosures.  
1.2 Interlayer materials are used to laminate glass-to-glass, glass-to-plastic, and plastic-to-plastic. Interlayer materials are basically transparent adhesives with high-quality optical properties. They can also serve as an energy absorbing medium, a fail-safe membrane to contain cockpit pressure and to prevent entry of impact debris; a strain insulator to accommodate different thermal expansion rates of members being laminated and as an adherent to prevent spalling of inner surface ply material fragments. The relative importance of an interlayer characteristic will be a function of the prime use it serves in its particular application.  
1.3 This guide, as a summary of various methods in Section 2, is intended to facilitate the selection of tests that can be applied to interlayer materials.  
1.4 The test methods listed are for use in determining basic design characteristics and in assuring lot-to-lot uniformity of the materials being tested except as noted in 3.3.  
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    2 pages
    English language
    sale 15% off
ASTM
ASTM D6412/D6412M-99(2020)(Specification)
Standard Specification for Epoxy (Flexible) Adhesive For Bonding Metallic And Nonmetallic Materials

ABSTRACT
The specification covers a two-part modified epoxy paste adhesive for bonding metallic and nonmetallic materials. The adhesive should be suitable for forming bonds that can withstand environmental exposure to a certain temperature range when exposed to an expected combination of stress, temperature, and relative humidity to be encountered in service. Two types of adhesive shall be classified according to composition. Type I which consists of two-part kits of liquid base and modified amide liquid accelerator. Type I is further subdivided into two grades: Grade 1 with low viscosity and Grade 2 with high viscosity. The other classification is Type II which consists of premixed, frozen, Type I, Grade 1 or Type I, Grade 2. Different tests shall be conducted in order to determine the following mechanical properties of the adhesives: room-temperature shear, high-temperature shear, low-temperature shear, room-temperature Shore D hardness, room-temperature T-peel, and outgassing characteristics such as total mass loss and vacuum condensable material.
SCOPE
1.1 The specification covers a two-part modified epoxy paste adhesive for bonding metallic and nonmetallic materials. The adhesive should be suitable for forming bonds that can withstand environmental exposure to temperatures from –184 to 82 °C [–300 to 180 °F] when exposed to an expected combination of stress, temperature, and relative humidity to be encountered in service.
Note 1: When coordinated through the Department of Defense (DoD) and the National Aeronautics and Space Administration (NASA), this practice will be a direct replacement of MIL-A-82720 (OS), MIS-26872, and MSFC-SPEC-2037.  
1.2 The values stated in SI units or inch-pound units are to be regarded separately as standard. Within the text, the inch-pound units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with this specification.  
1.3 The following precautionary statement pertains to the test method portion only, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    4 pages
    English language
    sale 15% off
ASTM
ASTM D6464-03a(2017)(Specification)
Standard Specification for Expandable Foam Adhesives for Fastening Gypsum Wallboard to Wood Framing

ABSTRACT
This specification establishes minimum performance requirements for determining strength, aging, and working properties of expandable foam adhesives intended for bonding back surfaces of gypsum wallboards of all thicknesses to wood framing. Minimum physical and performance requirements are specified for all measured properties of adhesives and adhesive bonds. Shear strength, tensile strength, adhesive open assembly time determination, substrate wet-out by adhesive, accelerated adhesive aging, freeze-thaw stability, suitability of a laminating adhesive for vinyl-covered wallboard, suitability for stain resistance for vinyl-covered wallboard, and gap filling tests shall be performed to conform to the specified requirements.
SCOPE
1.1 This specification establishes minimum performance requirements for determining strength, aging, and working properties of expandable foam adhesives intended for bonding back surfaces of gypsum wallboards of all thicknesses to wood framing. Minimum physical and performance requirements are specified for all measured properties of adhesives and adhesive bonds.  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    8 pages
    English language
    sale 15% off
ASTM
ASTM D6465-99(2016)(Guide)
Standard Guide for Selecting Aerospace and General Purpose Adhesives and Sealants

SIGNIFICANCE AND USE
5.1 The guide is to be used by anyone developing bonding or sealing requirements for specifications for manufacturing, maintenance or overhaul. This guide has been designed to be application specific for each bonding or sealing application, and allows the design engineer to rest assured that the product(s) or process(es) selected by the industrial or manufacturing engineer will be compatible with both the part material and the subsequent processes, such as adherend/substrate cleaning and preparation. It allows the industrial or manufacturing engineer to customize the selection of the adhesive or sealant product based on the materials of the parts being bonded or sealed, the conditions required for the subsequent process(es), environmental, cost, and health and safety concerns.
SCOPE
1.1 This guide is intended to assist design engineers, manufacturing/industrial engineers, and production managers in selecting the best-fit adhesive/sealant or bonding/sealing process. The guide takes into account environmental pollution prevention and occupational health and safety factors in a selection process.  
1.2 This guide is not to be considered as a database of acceptable materials. It will guide the engineers and managers through the adhesive/sealant material selection process, calling for engineers to customize their selection based on the bonding or sealing performance requirements for the specified application. A comprehensive selection process will allow for the establishment of a more efficient production process, and may eliminate unnecessary process steps. A total life cycle cost analysis or performance/cost of implementation study is recommended to compare the available alternatives.  
1.3 This guide is for aerospace and general purpose operations. It is not intended to be used for automotive, carpet, construction, electronics, medical/dental, optical, or structural and nonstructural wood applications. Note that this guide is not specifically for these applications, but the general methodology may be used in the selection process for these applications.  
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  • Guide
    7 pages
    English language
    sale 15% off
ASTM
ASTM B637-23(Specification)
Standard Specification for Precipitation-Hardening and Cold Worked Nickel Alloy Bars, Forgings, and Forging Stock for Moderate or High Temperature Service

ABSTRACT
This specification covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Chemical analysis shall be performed on the alloy and shall conform to the chemical composition requirement in carbon, manganese, silicon, phosphorus, sulfur, chromium, cobalt, molybdenum, columbium, tantalum, titanium, aluminum, zirconium, boron, iron, copper, and nickel. The material shall follow recommended annealing treatment, solution treatment, stabilizing treatment, and precipitation hardening treatment. Tension testing, hardness testing and stress-rupture testing shall be performed on the material and shall comply to the required tensile strength, yield strength, elongation, reduction in area, and Brinell hardness.
SCOPE
1.1 This specification2 covers hot- and cold-worked precipitation-hardenable nickel alloy rod, bar, forgings, and forging stock for moderate or high temperature service (Table 1).  
1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Safety Data Sheet (SDS) for this product/material as provided by the manufacturer, to establish appropriate safety, health, and environmental practices, and determine the applicability of regulatory limitations prior to use.  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Technical specification
    7 pages
    English language
    sale 15% off
  • Technical specification
    7 pages
    English language
    sale 15% off
ASTM
ASTM C596-23(Test Method)
Standard Test Method for Drying Shrinkage of Mortar Containing Hydraulic Cement

SIGNIFICANCE AND USE
4.1 This test method establishes a selected set of conditions of temperature, relative humidity and rate of evaporation of the environment to which a mortar specimen of stated composition shall be subjected for a specified period of time during which its change in length is determined and designated “drying shrinkage.”  
4.2 The drying shrinkage of mortar as determined by this test method has a linear relation to the drying shrinkage of concrete made with the same cement and exposed to the same drying conditions.4 Hence this test method may be used when it is desired to develop data on the effect of a hydraulic cement on the drying shrinkage of concrete made with that cement.
SCOPE
1.1 This test method determines the change in length on drying of mortar bars containing hydraulic cement and graded standard sand.  
1.2 The values stated in SI units are to be regarded as standard. When combined standards are referenced, the selection of measurement system is at the user’s discretion subject to the requirements of the referenced standard.  
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Warning—Fresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure).2  
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Standard
    4 pages
    English language
    sale 15% off
  • Standard
    4 pages
    English language
    sale 15% off
ASTM
ASTM F3337-23(Guide)
Standard Guide for Taking Property and Behavior Measurements on Weathered Fractions of Oil

SIGNIFICANCE AND USE
5.1 A standard procedure is necessary to establish property changes for spilled oils or petroleum products at different oil weathering stages.  
5.2 This procedure employs standardized equipment, and test procedures.  
5.3 This procedure should be performed at the stages of weathering corresponding to the spill conditions of interest.
SCOPE
1.1 This guide summarizes methods to fractionate oil by evaporative weathering and then measure the properties and behavior of the weathered oil. The results of this guide can provide oil behavior data for input into oil spill models and response method selection.  
1.2 This guide covers general procedures for oil weathering and behavior and does not cover all possible procedures which may be applicable to this topic.  
1.3 The results obtained using this guide are intended to provide baseline data for the behavior of oil and petroleum products when spilled and input to oil spill models.  
1.4 The results obtained using this guide can be used directly to predict certain facets of oil spill behavior or as input to oil spill models.  
1.5 The accuracy of the guide depends very much on the representative nature of the oil sample used. Certain oils can have different properties depending on their chemical contents at the moment a sample is taken.  
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.  
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.  
1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

  • Guide
    4 pages
    English language
    sale 15% off
  • Guide
    4 pages
    English language
    sale 15% off