ASTM A234/A234M-10
(Specification)Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service
Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Moderate and High Temperature Service
ABSTRACT
This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction. These fittings are for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures. The material for fittings shall consist of killed steel, forgings, bars, plates, seamless or fusion-welded tubular products with filler metal added. Forging or shaping operations may be performed by hammering, pressing, piercing, extruding, upsetting, rolling, bending, fusion welding, machining, or by a combination of two or more of these operations. The forming procedure shall be so applied that it will not produce injurious imperfections in the fittings. Fittings, after forming at an elevated temperature, shall be cooled to a temperature below the critical range under suitable conditions to prevent injurious defects caused by too rapid cooling, but in no case more rapidly than the cooling rate in still air. The fittings shall be subjected to tension test, hardness test, and hydrostatic test.
SCOPE
1.1 This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction covered by the latest revision of ASME B16.9, B16.11, MSS-SP-79, MSS-SP-83, MSS-SP-95, and MSS-SP-97. These fittings are for use in pressure piping and in pressure vessel fabrication for service at moderate and elevated temperatures. Fittings differing from these ASME and MSS standards shall be furnished in accordance with Supplementary Requirement S58 of Specification A960/A960M.
1.2 Optional supplementary requirements are provided for fittings where a greater degree of examination is desired. When desired, one or more of these supplementary requirements may be specified in the order.
1.3 This specification does not cover cast welding fittings or fittings machined from castings. Cast steel welding fittings are governed by Specifications A216/A216M and A217/A217M.
1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Used in USDOE-NE Standards
Designation: A234/A234M – 10
Standard Specification for
Piping Fittings of Wrought Carbon Steel and Alloy Steel for
1
Moderate and High Temperature Service
This standard is issued under the fixed designationA234/A234M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (ϵ) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
3
1. Scope* 2.2 ASTM Standards:
2
A216/A216M Specification for Steel Castings, Carbon,
1.1 This specification covers wrought carbon steel and
Suitable for Fusion Welding, for High-Temperature Ser-
alloysteelfittingsofseamlessandweldedconstructioncovered
vice
by the latest revision of ASME B16.9, B16.11, MSS-SP-79,
A217/A217M Specification for Steel Castings, Martensitic
MSS-SP-83, MSS-SP-95, and MSS-SP-97. These fittings are
Stainless and Alloy, for Pressure-Containing Parts, Suit-
for use in pressure piping and in pressure vessel fabrication for
able for High-Temperature Service
service at moderate and elevated temperatures. Fittings differ-
A960/A960M Specification for Common Requirements for
ing from theseASME and MSS standards shall be furnished in
Wrought Steel Piping Fittings
accordance with Supplementary Requirement S58 of Specifi-
4
2.3 ASME Standards:
cation A960/A960M.
B16.9 Steel Butt-Welding Fittings
1.2 Optional supplementary requirements are provided for
B16.11 Forged Steel Fittings, SocketWelding andThreaded
fittingswhereagreaterdegreeofexaminationisdesired.When
4
2.4 ASME Boiler and Pressure Vessel Code:
desired, one or more of these supplementary requirements may
Section V Nondestructive Examination
be specified in the order.
Section VIII, Division 1, Pressure Vessels
1.3 This specification does not cover cast welding fittings or
Section IX Welding Qualifications
fittings machined from castings. Cast steel welding fittings are
5
2.5 MSS Standards:
governed by Specifications A216/A216M and A217/A217M.
MSS-SP-25 Standard Marking System for Valves, Fittings,
1.4 This specification is expressed in both inch-pound units
Flanges, and Unions
and in SI units. However, unless the order specifies the
MSS-SP-79 Socket Welding Reducer Inserts
applicable “M” specification designation (SI units), the mate-
MSS-SP-83 Steel Pipe Unions, Socket-Welding and
rial shall be furnished to inch-pound units.
Threaded
1.5 The values stated in either SI units or inch-pound units
MSS-SP-95 Swage(d) Nipples and Bull Plugs
are to be regarded separately as standard. Within the text, the
MSS-SP-97 Integrally Reinforced Forged Branch Outlet
SI units are shown in brackets. The values stated in each
Fittings—Socket Welding, Threaded and Buttwelding
system may not be exact equivalents; therefore, each system
Ends
shall be used independently of the other. Combining values
6
2.6 ASNT Standard:
from the two systems may result in non-conformance with the
SNT-TC-1A Recommended Practice for Nondestructive
standard.
Testing Personnel Qualification and Certification
2. Referenced Documents
2.1 In addition to those reference documents listed in
Specification A960/A960M, the following list of standards
3
apply to this specification.
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, the ASTM website.
4
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee Available from American Society of Mechanical Engineers (ASME), ASME
A01.22 on Steel Forgings andWrought Fittings for PipingApplications and Bolting International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
Materials for Piping and Special Purpose Applications. www.asme.org.
5
Current edition approved May 1, 2010. Published June 2010. Originally AvailablefromManufacturersStandardizationSocietyoftheValveandFittings
approved in 1940. Last previous edition approved in 2007 as A234/A234M–07. Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http://www.mss-
DOI: 10.1520/A0234_A0234M-10. hq.com.
2 6
For ASME Boiler and Pressure Vessel Code applications see related Specifi- AvailablefromAmericanSocietyforNondestructiveTesting(ASNT),P.O.Box
cation SA-234 in Section II of that Code. 28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http://www.asnt.org.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Used in USDOE-NE Standards
Designation:A234/A234M–07 Designation: A234/A234M – 10
Standard Specification for
Piping Fittings of Wrought Carbon Steel and Alloy Steel for
1
Moderate and High Temperature Service
This standard is issued under the fixed designationA234/A234M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction covered by the
latest revision of ASME B16.9, B16.11, MSS-SP-79, MSS-SP-83, and MSS-SP-95, MSS-SP-95, and MSS-SP-97. These fittings
areforuseinpressurepipingandinpressurevesselfabricationforserviceatmoderateandelevatedtemperatures.Fittingsdiffering
from these ASME and MSS standards shall be furnished in accordance with Supplementary Requirement S58 of Specification
A960/A960M.
1.2 Optional supplementary requirements are provided for fittings where a greater degree of examination is desired. When
desired, one or more of these supplementary requirements may be specified in the order.
1.3 This specification does not cover cast welding fittings or fittings machined from castings. Cast steel welding fittings are
governed by Specifications A216/A216M and A217/A217M.
1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable
“M” specification designation (SI units), the material shall be furnished to inch-pound units.
1.5 The values stated in either inch-poundSI units or SIinch-pound units are to be regarded separately as standard. Within the
text, the SI units are shown in brackets. The values stated in each system aremay not be exact equivalents; therefore, each system
mustshall be used independently of the other. Combining values from the two systems may result in non-conformance with the
specification. standard.
2. Referenced Documents
2.1 In addition to those reference documents listed in Specification A960/A960M, the following list of standards apply to this
specification.
3
2.2 ASTM Standards:
A216/A216M Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service
A217/A217M Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for
High-Temperature Service
A960/A960M Specification for Common Requirements for Wrought Steel Piping Fittings
4
2.3 ASME Standards:
B16.9 Steel Butt-Welding Fittings
B16.11 Forged Steel Fittings, Socket Welding and Threaded
4
2.4 ASME Boiler and Pressure Vessel Code:
Section V Nondestructive Examination
Section VIII, Division 1, Pressure Vessels
Section IX Welding Qualifications
5
2.5 MSS Standards:
MSS-SP-25 Standard Marking System for Valves, Fittings, Flanges, and Unions
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.22
on Steel Forgings and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications.
Current edition approved MarchMay 1, 2007.2010. Published April 2007.June 2010. Originally approved in 1940. Last previous edition approved in 20062007 as
A234/A234M–06a.A234/A234M–07. DOI: 10.1520/A0234_A0234M-107.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-234 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
www.asme.org.
5
Available from Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http://www.mss-hq.com.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A234/A234M – 10
MSS-SP-79 Socket Welding Reducer Inserts
MSS-SP-8
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Used in USDOE-NE Standards
Designation:A234/A234M–07 Designation: A234/A234M – 10
Standard Specification for
Piping Fittings of Wrought Carbon Steel and Alloy Steel for
1
Moderate and High Temperature Service
This standard is issued under the fixed designationA234/A234M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope*
2
1.1 This specification covers wrought carbon steel and alloy steel fittings of seamless and welded construction covered by the
latest revision of ASME B16.9, B16.11, MSS-SP-79, MSS-SP-83, and MSS-SP-95, MSS-SP-95, and MSS-SP-97. These fittings
areforuseinpressurepipingandinpressurevesselfabricationforserviceatmoderateandelevatedtemperatures.Fittingsdiffering
from these ASME and MSS standards shall be furnished in accordance with Supplementary Requirement S58 of Specification
A960/A960M.
1.2 Optional supplementary requirements are provided for fittings where a greater degree of examination is desired. When
desired, one or more of these supplementary requirements may be specified in the order.
1.3 This specification does not cover cast welding fittings or fittings machined from castings. Cast steel welding fittings are
governed by Specifications A216/A216M and A217/A217M.
1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable
“M” specification designation (SI units), the material shall be furnished to inch-pound units.
1.5 The values stated in either inch-poundSI units or SIinch-pound units are to be regarded separately as standard. Within the
text, the SI units are shown in brackets. The values stated in each system aremay not be exact equivalents; therefore, each system
mustshall be used independently of the other. Combining values from the two systems may result in non-conformance with the
specification. standard.
2. Referenced Documents
2.1 In addition to those reference documents listed in Specification A960/A960M, the following list of standards apply to this
specification.
3
2.2 ASTM Standards:
A216/A216M Specification for Steel Castings, Carbon, Suitable for Fusion Welding, for High-Temperature Service
A217/A217M Specification for Steel Castings, Martensitic Stainless and Alloy, for Pressure-Containing Parts, Suitable for
High-Temperature Service
A960/A960M Specification for Common Requirements for Wrought Steel Piping Fittings
4
2.3 ASME Standards:
B16.9 Steel Butt-Welding Fittings
B16.11 Forged Steel Fittings, Socket Welding and Threaded
4
2.4 ASME Boiler and Pressure Vessel Code:
Section V Nondestructive Examination
Section VIII, Division 1, Pressure Vessels
Section IX Welding Qualifications
5
2.5 MSS Standards:
MSS-SP-25 Standard Marking System for Valves, Fittings, Flanges, and Unions
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.22
on Steel Forgings and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications.
Current edition approved MarchMay 1, 2007.2010. Published April 2007.June 2010. Originally approved in 1940. Last previous edition approved in 20062007 as
A234/A234M–06a.A234/A234M–07. DOI: 10.1520/A0234_A0234M-107.
2
For ASME Boiler and Pressure Vessel Code applications see related Specification SA-234 in Section II of that Code.
3
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
4
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://
www.asme.org.
5
Available from Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http://www.mss-hq.com.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A234/A234M – 10
MSS-SP-79 Socket Welding Reducer Inserts
MSS-SP-8
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.