ASTM D7148-07(2011)
(Test Method)Standard Test Method for Determining the Ionic Resistivity (ER) of Alkaline Battery Separator Using a Carbon Electrode in an Electrolyte Bath Measuring System
Standard Test Method for Determining the Ionic Resistivity (ER) of Alkaline Battery Separator Using a Carbon Electrode in an Electrolyte Bath Measuring System
SIGNIFICANCE AND USE
The ER of a battery separator is a standard measurement used by separator and battery manufacturers for quality control purposes and separator selection.
Separator ER and the separator's interaction with the electrolyte, that is resistance to wetting or flow, will contribute to the internal resistance of the battery and this can potentially limit the electrical output of a battery. The ER determination is a tool for battery manufacturers to use in design, material selection, and performance specifications.
The change in the bath electrical resistance imparted by a separator is affected by the porosity, thickness, and tortuousity of the pore structure of the separator, the wettability of the separator to the electrolyte, and the temperature and concentration of the electrolyte.
Incomplete wetting or saturation of the pore structure limits the lowest ER value obtainable from a separator structure. Separators are pretreated to assure that the specimen being tested has been adequately wetted out. A separator that is not fully wetted out (saturated) will give a higher ER.
This test method is intended to give a rapid and repeatable measurement that approximates the change in ER that could happen when the separator is used in a battery.
SCOPE
1.1 This test method covers the pretreatment, test conditions, apparatus, and procedure to determine the ionic resistivity, commonly referred to in the battery industry as electrical resistance (ER) of an alkaline battery separator immersed in an electrolyte of 40 % potassium hydroxide (KOH).
1.2 The values stated in SI units are to be regarded as the standard.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D7148 − 07(Reapproved 2011)
Standard Test Method for
Determining the Ionic Resistivity (ER) of Alkaline Battery
Separator Using a Carbon Electrode in an Electrolyte Bath
Measuring System
This standard is issued under the fixed designation D7148; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 3.1.1 barrier resistance (RB), n—the resistance of the bath
with a solid, nonporous sheet of alkaline resistant, electrical
1.1 This test method covers the pretreatment, test
insulation that separates the electrodes.
conditions, apparatus, and procedure to determine the ionic
3.1.2 bath resistance (RC), n—the resistance of the bath
resistivity, commonly referred to in the battery industry as
without the specimen (separator).
electrical resistance (ER) of an alkaline battery separator
immersed in an electrolyte of 40% potassium hydroxide
3.1.3 bath resistance (RT), n—the total electrical resistance
(KOH).
of the bath and a separator specimen.
1.2 The values stated in SI units are to be regarded as the
3.1.4 battery separator, n—an ion-permeable, nonconduc-
standard. tivematerialthatpreventselectricalcontactbetweenelectrodes
of opposite polarity.
1.3 This standard does not purport to address all of the
3.1.5 electrolyte, n—a 40% potassium hydroxide solution.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
3.1.6 ionic resisitivity (ER), n—the product of a change in
priate safety and health practices and determine the applica-
electrical resistance times an area.
bility of regulatory limitations prior to use.
3.1.6.1 Discussion—Theareaistheapertureareadividedby
thenumberofseparatorsbetweentheelectrodes.Thechangein
2. Referenced Documents
resistanceisthedifference,inohms,oftheelectricalresistance
2.1 ASTM Standards:
with and without the seperator(s). The SI units for ER are
D1711Terminology Relating to Electrical Insulation
ohms-metre but the customary practice in the battery industry
2.2 Battery Council International:
istoreporttheERinunitsofohms-cm .Itshouldbenotedthat
Standard Test Method for Determining the Electrical Resis-
this terminology is not in conflict with Terminology D1711.
tance of a Battery Separator Using a Palico Measuring
3.2 Symbols:
System,Section 3.3b
3.2.1 ER—asymbol,peculiartothebatteryindustry,denot-
ing that characteristic of a sheet material that is related to the
3. Terminology
rate of transfer of ions through the interstices of a porous sheet
3.1 Definitions of Terms Specific to This Standard:
immersed between two carbon electrodes in an aqueous
electroyte.
This test method is under the jurisdiction of ASTM Committee D09 on
4. Summary of Test Method
Electrical and Electronic Insulating Materials and is the direct responsibility of
Subcommittee D09.19 on Dielectric Sheet and Roll Products.
4.1 This test method detects small changes in ohmic resis-
Current edition approved April 1, 2011. Published April 2011. Last previous
tance between carbon electrodes immersed in an alkaline
edition approved in 2007 as D7148–07. DOI: 10.1520/D7148-07R11.
electrolyte with and without separator material between the
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
carbon electrodes. This change is related to the rate of transfer
Standards volume information, refer to the standard’s Document Summary page on
ofionsthroughaseparatormaterial.TheERiscalculatedfrom
the ASTM website.
3 th the fixed aperture area. The sensitivity and resolution of the
AvailablefromBatteryCouncilInternational,401N.MichiganAve.,24 Floor,
Chicago, IL 60611-4267. apparatus detects electrical resistance changes of 60.1%.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
D7148 − 07 (2011)
5. Significance and Use tions. Enclose the glass-mixing bottle in a plastic container of
sufficient capacity to contain the solution in case of bottle
5.1 TheERofabatteryseparatorisastandardmeasurement
breakage.Topreventexcessiveheating,addconcentratedKOH
usedbyseparatorandbatterymanufacturersforqualitycontrol
slowly to water with adequate agitation to produce thorough
purposes and separator selection.
mixing. The diluted KOH is sufficiently corrosive at both
5.2 Separator ER and the separator’s interaction with the
ambient and elevated temperatures that careful handling is
electrolyte, that is resistance to wetting or flow, will contribute
necessary to prevent injury or damage.
to the internal resistance of the battery and this can potentially
8.2 The hazard associated with mixing KOH with water is
limittheelectricaloutputofabattery.TheERdeterminationis
that it generates a lot of heat as it dissolves; this has the
a tool for battery manufacturers to use in design, material
potential to lead to spattering. A concentrated KOH solution
selection, and performance specifications.
willerodeskinandeyes.Avoidthesehazardsbywearingsafety
5.3 The change in the bath electrical resistance imparted by
glasses, face shield, and protective gloves, and immediately
a separator is affected by the porosity, thickness, and tortuous-
rinsing with water if any skin contact occurs. (If any eye
ity of the pore structure of the separator, the wettability of the
contact occurs, flush the eyes with water for 15 min and then
separator to the electrolyte, and the temperature and concen-
get medical attention.)
tration of the electrolyte.
5.4 Incomplete wetting or saturation of the pore structure
9. Sampling, Test Specimens, and Test Units
limits the lowest ER value obtainable from a separator struc-
9.1 Select samples representative of the separator material
ture. Separators are pretreated to assure that the specimen
to be tested.
beingtestedhasbeenadequatelywettedout.Aseparatorthatis
not fully wetted out (saturated) will give a higher ER.
9.2 Use a specimen size of at least 120 by 120 mm and no
5.5 This test method is intended to give a rapid and larger than what will fit in the bath.
repeatable measurement that approximates the change in ER
9.3 If specimens require identification, use an alkaline
that could happen when the separator is used in a battery.
resistant marker. Mark an area of the specimen that will not
interfere with the ion transfer through the separator.
6. Apparatus
6.1 Stainless steel container or equivalent to accommodate
10. Preparation of Apparatus
the separator test samples.
10.1 Fill the ER bath with prepared battery electrolyte (40
6.2 Hot plate or other heating device suitable to boil water.
61%KOHsolution)toalevelabovetheapertureopening(12
6.3 Stainless steel screen.
to 25 mm below the top of the ER bath). Adjust the bath’s
6.4 Glass or plastic separator tank for presoaking separators temperature to 25 6 5°C .
in battery electrolyte.
10.2 Connect the electrodes to the resistance meter control
6.5 Interval timer.
unit using alkali-resistant wire and hardware.
6.6 Safety glasses.
10.3 Turn on the resistance meter. Allow the equipment to
6.7 Thermometer.
stabilize for at least 20 min. If the meter includes a standard
reference resistor (place in “Standby” mode and “Standard”
6.8 Alkaline resistant gloves, that is neoprene latex or
scaling on the resistance meter control unit and set to the
polyethylene gloves.
appropriate resistance range scale for a 0.200-Ω resistor
6.9 Plastic tongs for handling KOH-wetted separators.
reading). Unless the meter reading is within 60.1% of the
6.10 ERbathwithafixedaperturearea(32cm isstandard) value of the resistor, service will be required.
that puts a uniform current flux through a fixed area of the
10.4 If available, check the resistance standard for the
separator sample for measurement.Adrawing of an ER bath is
systemoutlinedin11.4.Ifthisagreeswithin 61%,proceedto
included in Annex A1.
Section 13.
6.11 A.C. resistance meter or bridge with sufficient sensi-
10.5 Periodically, or when problems occur or changes are
tivityandresolutiontomeasure 60.1%changeintheERbath
made to the system, test the stability, polarization, current
resistance in the presence of potentials generated in the ER
leakage,andstandardizationusingthemaintenanceprocedures
bath.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.