ASTM C1490-01
(Guide)Standard Guide for the Selection, Training and Qualification of Nondestructive Assay (NDA) Personnel
Standard Guide for the Selection, Training and Qualification of Nondestructive Assay (NDA) Personnel
SCOPE
1.1 This guide contains good practices for the selection, training, qualification, and professional development of personnel performing analysis, calibration, physical measurements, or data review using nondestructive assay equipment, methods, results, or techniques. The guide also covers NDA personnel involved with NDA equipment setup, selection, diagnosis, troubleshooting, or repair. Selection, training, and qualification programs based on this guide are intended to provide assurance that NDA personnel are qualified to perform their jobs competently. This guide presents a series of options but does not recommend a specific course of action.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: C 1490 – 01
Standard Guide for
the Selection, Training and Qualification of Nondestructive
1
Assay (NDA) Personnel
This standard is issued under the fixed designation C 1490; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
1. Scope C 1458 Test Method for Non-destructive Assay of Pluto-
241
2
nium, Tritium and Am by Calorimetric Assay
1.1 This guide contains good practices for the selection,
2.2 U.S. Government Documents:
training, qualification, and professional development of per-
10 CFR 830.120 Code of Federal Regulations, Title 10, Part
sonnel performing analysis, calibration, physical measure-
3
830, Paragraph 120, Quality Assurance Requirements
ments, or data review using nondestructive assay equipment,
DOE Order 5480.20A
methods, results, or techniques. The guide also covers NDA
DOE QAPD CAO-94–1012 U.S. Department of Energy,
personnel involved with NDA equipment setup, selection,
Quality Assurance Program Document
diagnosis, troubleshooting, or repair. Selection, training, and
TWCP-QAPP CAO-94–1010 TRU Waste Characterization
qualification programs based on this guide are intended to
Quality Assurance Program Plan
provide assurance that NDA personnel are qualified to perform
their jobs competently. This guide presents a series of options
3. Significance and Use
but does not recommend a specific course of action.
3.1 The process of selection, training and qualification of
2. Referenced Documents personnel involved with NDA measurements is one of the
quality assurance elements for an overall quality NDA mea-
2.1 ASTM Standards:
surement program.
C 1030 Test Method for Determination of Plutonium Isoto-
2
3.2 This guide describes an approach to selection, qualifi-
pic Composition by Gamma-Ray Spectrometry
cation, and training of personnel that is to be used in conjunc-
C 1133 Test Method for Nondestructive Assay of Special
tion with other NDA QA program elements. The selection,
Nuclear Material in Low-Density Scrap and Waste by
2
qualification and training processes can vary and this guide
Segmented Passive Gamma-Ray Scanning
provides one such approach.
C 1207 Test Method for Nondestructive Assay of Plutonium
3.3 The qualification activities described in this guide as-
in Scrap and Waste by Passive Neutron Coincidence
2
sume that NDA personnel are already proficient in general
Counting
facility operations and safety procedures. The training and
C 1221 Test Method for Nondestructive Analysis of Special
activities that developed this proficiency are not covered in this
Nuclear Materials in Homogeneous Solutions by Gamma-
2 guide.
Ray Spectrometry
3.4 This guide describes a basic approach and principles for
C 1268 Test Method for the Quantitative Determination of
the qualification of NDA professionals and technical specialists
Americium 241 in Plutonium by Gamma-Ray Spectrom-
2
and operators. A different approach may be adopted by the
etry
management organization based on its particular organization
C 1316 Test Method for Nondestructive Assay of Nuclear
and facility specifics. However, if a variation of the approach
Material in Scrap and Waste by Passive-Active Neutron
252 2
of this guide is applied, the resulting selection, training, and
Counting Using a Cf Shuffler
qualification programs must meet the requirements of the
C 1455 Guide for Nondestructive Assay of Special Nuclear
facility quality assurance program and should provide all the
Material Holdup Using Gamma-Ray Spectrometric Meth-
2
applicable functions of Section 4.
ods
3.5 This guide may be used as an aid in the preparation of
a Training Implementation Plan (TIP) for the Transuranic
1
Waste Characterization Program (TWCP). Requirements for
This guide is under the jurisdiction of ASTM Committee C26 on Nuclear Fuel
Cycle and is the direct responsibility of Subcommittee C26.10 on Non Destructive
Assay.
3
Current edition approved Jan. 10, 2001. Published March 2001. Available from the Superintendent of Documents, U.S. Government Printing
2
Annual Book of ASTM Standards, Vol 12.01. Office, Washington, DC 20402.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
C 1490
TWCP training include but are not limited to: 10 CFR 830.120, 4.2.2.3 Duties—Expert technical data review (ETR). NDA
DOE Order 5480.20A, DOE QAPD CAO-94-1012, TWCP- measurement oversight. Performs routine instrument qualifica-
QAPP CAO-94-1010, TWCP-QAPjP and the TUM. tion, calibration, and validation. Reviews, approves measure-
ment control data. Provides c
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.