ASTM A1016/A1016M-11a
(Specification)Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
Standard Specification for General Requirements for Ferritic Alloy Steel, Austenitic Alloy Steel, and Stainless Steel Tubes
ABSTRACT
This specification covers general requirements for ferritic alloy steel, austenitic alloy steel, and stainless steel tubes. The steel shall made by any process. The material shall conform to the tensile property requirements prescribed in the individual product specification. Yield strength tests and elongation tests shall be made to conform to the requirements. Flattening test, reverse flattening test, reverse bend test, flaring test, flange test, hardness test, ultrasonic test, eddy current test, flux leakage test, and hydrostatic test shall be made to conform to the requirements specified.
SCOPE
1.1 This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A1016/A1016M −11a
StandardSpecification for
General Requirements for Ferritic Alloy Steel, Austenitic
1
Alloy Steel, and Stainless Steel Tubes
This standard is issued under the fixed designation A1016/A1016M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* SI units are shown in brackets. The values stated in each
system may not be exact equivalents; therefore, each system
1.1 This specification covers a group of requirements that,
shall be used independently of the other. Combining values
unless otherwise specified in an individual specification, shall
from the two systems may result in non-conformance with the
apply to the ASTM product specifications noted below.
standard. The inch-pound units shall apply unless the “M”
Title of Specification ASTM
designation (SI) of the product specification is specified in the
A
Designation
order.
Seamless Carbon-Molybdenum Alloy-Steel Boiler and A209/A209M
Superheater Tubes
2. Referenced Documents
Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, A213/A213M
and Heat-Exchanger Tubes 2
2.1 ASTM Standards:
Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, A249/A249M
A209/A209M Specification for Seamless Carbon-
and Condenser Tubes
Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and A250/A250M
Molybdenum Alloy-Steel Boiler and Superheater Tubes
Superheater Tubes
A213/A213M Specification for Seamless Ferritic and Aus-
Seamless and Welded Ferritic and Martensitic Stainless Steel A268/A268M
tenitic Alloy-Steel Boiler, Superheater, and Heat-
Tubing for General Service
Seamless and Welded Austenitic Stainless Steel Tubing for A269
Exchanger Tubes
General Service
A249/A249M Specification for Welded Austenitic Steel
Seamless and Welded Austenitic Stainless Steel Sanitary TubingA270
Boiler, Superheater, Heat-Exchanger, and Condenser
Seamless and Welded Carbon and Alloy-Steel Tubes for A334/A334M
Low-Temperature Service
Tubes
Welded Austenitic Stainless Steel Feedwater Heater Tubes A668/A668M
A250/A250M Specification for Electric-Resistance-Welded
Austenitic Stainless Steel Tubing for Breeder Reactor Core A771/A771M
Components Ferritic Alloy-Steel Boiler and Superheater Tubes
Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing A789/A789M
A268/A268M Specification for Seamless and Welded Fer-
for General Service
ritic and Martensitic Stainless Steel Tubing for General
Welded Ferritic Stainless Steel Feedwater Heater Tubes A803/A803M
Service
Austenitic and Ferritic Stainless Steel Duct Tubes for Breeder A826/A826M
Reactor Core Components
A269 Specification for Seamless and Welded Austenitic
High-Frequency Induction Welded, Unannealed Austenitic Steel A851
Stainless Steel Tubing for General Service
Condenser Tubes
A A270 Specification for Seamless and WeldedAustenitic and
These designations refer to the latest issue of the respective specifications.
Ferritic/Austenitic Stainless Steel Sanitary Tubing
1.2 In the case of conflict between a requirement of a
A334/A334M Specification for Seamless and Welded Car-
product specification and a requirement of this general require-
bon and Alloy-Steel Tubes for Low-Temperature Service
ments specification, the product specification shall prevail. In
A370 Test Methods and Definitions for Mechanical Testing
the case of conflict between a requirement of the product
of Steel Products
specification or a requirement of this general requirements
A530/A530M Specification for General Requirements for
specification and a more stringent requirement of the purchase
Specialized Carbon and Alloy Steel Pipe
order, the purchase order shall prevail.
A668/A668M Specification for Steel Forgings, Carbon and
1.3 The values stated in either SI units or inch-pound units
Alloy, for General Industrial Use
are to be regarded separately as standard. Within the text, the
A700 Practices for Packaging, Marking, and Loading Meth-
ods for Steel Products for Shipment
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee
2
A01.10 on Stainless and Alloy Steel Tubular Products. For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Current edition approved May 15, 2011. Published June 2011. Originally contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
approved in 2001. Last previous edition approved in 2011 as A1016/A1016M–11. Standards volume information, refer to the standard’s Document Summary page on
DOI: 10.1520/A1016_A1016M-11a. the ASTM website.
*A Summary of Changes section appears
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A1016/A1016M–11 Designation: A1016/A1016M – 11a
Standard Specification for
General Requirements for Ferritic Alloy Steel, Austenitic
1
Alloy Steel, and Stainless Steel Tubes
This standard is issued under the fixed designation A1016/A1016M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply
to the ASTM product specifications noted below.
Title of Specification ASTM
A
Designation
Seamless Carbon-Molybdenum Alloy-Steel Boiler and A209/A209M
Superheater Tubes
Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, A213/A213M
and Heat-Exchanger Tubes
Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, A249/A249M
and Condenser Tubes
Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and A250/A250M
Superheater Tubes
Seamless and Welded Ferritic and Martensitic Stainless Steel A268/A268M
Tubing for General Service
Seamless and Welded Austenitic Stainless Steel Tubing for A269
General Service
Seamless and Welded Austenitic Stainless Steel Sanitary Tubing A270
Seamless and Welded Carbon and Alloy-Steel Tubes for A334/A334M
Low-Temperature Service
Welded Austenitic Stainless Steel Feedwater Heater Tubes A668/A668M
Austenitic Stainless Steel Tubing for Breeder Reactor Core A771/A771M
Components
Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing A789/A789M
for General Service
Welded Ferritic Stainless Steel Feedwater Heater Tubes A803/A803M
Austenitic and Ferritic Stainless Steel Duct Tubes for Breeder A826/A826M
Reactor Core Components
High-Frequency Induction Welded, Unannealed Austenitic Steel A851
Condenser Tubes
A
These designations refer to the latest issue of the respective specifications.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this general requirements
specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or
a requirement of this general requirements specification and a more stringent requirement of the purchase order, the purchase order
shall prevail.
1.3 ThevaluesstatedineitherSIunitsorinch-poundunitsaretoberegardedseparatelyasstandard.Withinthetext,theSIunits
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard. The
inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
2. Referenced Documents
2
2.1 ASTM Standards:
A209/A209M Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes
A213/A213M Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.10
on Stainless and Alloy Steel Tubular Products.
Current edition approved April 1,May 15, 2011. Published AprilJune 2011. Originally approved in 2001. Last previous edition approved in 20102011 as
A1016/A1016M–101. DOI: 10.1520/A1016_A1016M-11a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A1016/A1016M – 11a
A249/A249M Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes
A250/A250M Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes
A268/A268M Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service
A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A270 Specification for Seamless and Welded Austen
...
This document is not anASTM standard and is intended only to provide the user of anASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation:A1016/A1016M–11 Designation: A1016/A1016M – 11a
Standard Specification for
General Requirements for Ferritic Alloy Steel, Austenitic
1
Alloy Steel, and Stainless Steel Tubes
This standard is issued under the fixed designation A1016/A1016M; the number immediately following the designation indicates the
year of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last
reapproval. A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers a group of requirements that, unless otherwise specified in an individual specification, shall apply
to the ASTM product specifications noted below.
Title of Specification ASTM
A
Designation
Seamless Carbon-Molybdenum Alloy-Steel Boiler and A209/A209M
Superheater Tubes
Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, A213/A213M
and Heat-Exchanger Tubes
Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, A249/A249M
and Condenser Tubes
Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and A250/A250M
Superheater Tubes
Seamless and Welded Ferritic and Martensitic Stainless Steel A268/A268M
Tubing for General Service
Seamless and Welded Austenitic Stainless Steel Tubing for A269
General Service
Seamless and Welded Austenitic Stainless Steel Sanitary Tubing A270
Seamless and Welded Carbon and Alloy-Steel Tubes for A334/A334M
Low-Temperature Service
Welded Austenitic Stainless Steel Feedwater Heater Tubes A668/A668M
Austenitic Stainless Steel Tubing for Breeder Reactor Core A771/A771M
Components
Seamless and Welded Ferritic/Austenitic Stainless Steel Tubing A789/A789M
for General Service
Welded Ferritic Stainless Steel Feedwater Heater Tubes A803/A803M
Austenitic and Ferritic Stainless Steel Duct Tubes for Breeder A826/A826M
Reactor Core Components
High-Frequency Induction Welded, Unannealed Austenitic Steel A851
Condenser Tubes
A
These designations refer to the latest issue of the respective specifications.
1.2 In the case of conflict between a requirement of a product specification and a requirement of this general requirements
specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or
a requirement of this general requirements specification and a more stringent requirement of the purchase order, the purchase order
shall prevail.
1.3 ThevaluesstatedineitherSIunitsorinch-poundunitsaretoberegardedseparatelyasstandard.Withinthetext,theSIunits
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard. The
inch-pound units shall apply unless the “M” designation (SI) of the product specification is specified in the order.
2. Referenced Documents
2
2.1 ASTM Standards:
A209/A209M Specification for Seamless Carbon-Molybdenum Alloy-Steel Boiler and Superheater Tubes
A213/A213M Specification for Seamless Ferritic and Austenitic Alloy-Steel Boiler, Superheater, and Heat-Exchanger Tubes
1
This specification is under the jurisdiction ofASTM CommitteeA01 on Steel, Stainless Steel and RelatedAlloys and is the direct responsibility of SubcommitteeA01.10
on Stainless and Alloy Steel Tubular Products.
Current edition approved April 1,May 15, 2011. Published AprilJune 2011. Originally approved in 2001. Last previous edition approved in 20102011 as
A1016/A1016M–101. DOI: 10.1520/A1016_A1016M-11a.
2
For referencedASTM standards, visit theASTM website, www.astm.org, or contactASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1
---------------------- Page: 1 ----------------------
A1016/A1016M – 11a
A249/A249M Specification for Welded Austenitic Steel Boiler, Superheater, Heat-Exchanger, and Condenser Tubes
A250/A250M Specification for Electric-Resistance-Welded Ferritic Alloy-Steel Boiler and Superheater Tubes
A268/A268M Specification for Seamless and Welded Ferritic and Martensitic Stainless Steel Tubing for General Service
A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service
A270 Specification for Seamless and Welded Austen
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.