ASTM C443M-19a
(Specification)Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets (Metric)
Standard Specification for Joints for Concrete Pipe and Manholes, Using Rubber Gaskets (Metric)
ABSTRACT
This specification covers flexible watertight joints for concrete pipe and precast manhole sections, using rubber gaskets for sealing the joints, where infiltration or exfiltration is a factor in the design. The numerical values in this specification are not presented in inch-pound units, but rather, in metric or SI units only. All rubber gaskets shall meet the dimensions, tolerances, and physical requirements of both standard gasket and oil resistant gasket requirements. Assembled joints should pass the following performance test without leakage at the joints: pipes in straight alignment, and pipes in maximum deflected position.
SCOPE
1.1 This specification covers flexible leak-resistant joints for concrete pipe and precast manhole sections, using rubber gaskets for sealing the joints, where infiltration or exfiltration is a factor in the design. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specification C14M, Specification C76M, or Specification C507M and precast manhole section conforming in all other respects to Specification C478M, provided that if there is conflict in permissible variations in dimensions, the requirements of this specification for joints shall govern.
1.2 This specification is the metric counterpart of Specification C443.
Note 1: This specification covers the design and performance of the rubber gasket joint only. Joints covered by this specification are adequate for hydrostatic pressures up to 90 kPa (9 m), when tested per Section 9. Infiltration or exfiltration quantities for an installed pipeline are dependent upon many factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:C443M −19a
Standard Specification for
Joints for Concrete Pipe and Manholes, Using Rubber
1
Gaskets (Metric)
This standard is issued under the fixed designation C443M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope Storm Drain, and Culvert Pipe (Metric)
C76M Specification for Reinforced Concrete Culvert, Storm
1.1 Thisspecificationcoversflexibleleak-resistantjointsfor
Drain, and Sewer Pipe (Metric)
concrete pipe and precast manhole sections, using rubber
C478M Specification for Circular Precast Reinforced Con-
gasketsforsealingthejoints,whereinfiltrationorexfiltrationis
crete Manhole Sections (Metric)
a factor in the design. The specification covers the design of
C507M Specification for Reinforced Concrete Elliptical
joints and the requirements for rubber gaskets to be used
Culvert, Storm Drain, and Sewer Pipe (Metric)
therewith, for pipe conforming in all other respects to Speci-
C822 Terminology Relating to Concrete Pipe and Related
fication C14M, Specification C76M, or Specification C507M
Products
and precast manhole section conforming in all other respects to
C1619 Specification for Elastomeric Seals for Joining Con-
Specification C478M, provided that if there is conflict in
crete Structures
permissible variations in dimensions, the requirements of this
specification for joints shall govern.
3. Terminology
1.2 This specification is the metric counterpart of Specifi-
3.1 Definitions—Fordefinitionsoftermsrelatingtoconcrete
cation C443.
pipe, see Terminology C822.
NOTE 1—This specification covers the design and performance of the
4. Basis of Acceptance
rubber gasket joint only. Joints covered by this specification are adequate
for hydrostatic pressures up to 90 kPa (9 m), when tested per Section 9.
4.1 The acceptability of the pipe joints and gaskets shall be
Infiltration or exfiltration quantities for an installed pipeline are dependent
determinedbytheresultsofthephysicaltestsprescribedinthis
upon many factors other than the joints, and allowable quantities must be
specification, if and when required, and by inspection to
covered by other specifications and suitable testing of the installed
pipeline and system.
determine whether the pipe joints and gaskets conform to this
specification as to design and freedom from defects.
1.3 This international standard was developed in accor-
dance with internationally recognized principles on standard-
5. Materials and Manufacture for Gaskets
ization established in the Decision on Principles for the
5.1 All rubber gaskets shall comply with Specification
Development of International Standards, Guides and Recom-
C1619 in terms of materials and manufacture. The gaskets
mendations issued by the World Trade Organization Technical
shall be extruded or molded to the specified size within a
Barriers to Trade (TBT) Committee.
tolerance of 63 % on any dimension, measured at any cross
2. Referenced Documents section.
2
2.1 ASTM Standards:
6. Physical Requirements for Gaskets
C14M Specification for Nonreinforced Concrete Sewer,
6.1 Standard Gasket Requirements—All rubber gaskets
shall meet the dimensions, tolerances, and physical require-
ments of Specification C1619, Class C.
1
This specification is under the jurisdiction of ASTM Committee C13 on
Concrete Pipe and is the direct responsibility of Subcommittee C13.08 on Joints for
6.2 Oil Resistant Gasket Requirements—All rubber gaskets
Precast Concrete Structures.
shall meet the dimensions, tolerances, and physical require-
Current edition approved July 1, 2019. Published July 2019. Originally approved
ments of Specification C1619, Class D.
in 1980. Last previous edition approved in 2019 as C433M – 19. DOI: 10.1520/
C0443M-19A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 7. Design of Joints
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
7.1 The manufacturer shall furnish the owner with the
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. detailed design of the joint or joints including design and
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C443M−19a
durometer hardness of the rubber gasket proposed to be acceptable provided the designs are approved by the owner
furnished under this specification. prior to manufacture and provided the test pipe comply with
the specified tests.
7.1.1 The joint design shall consist of
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: C443M − 19 C443M − 19a
Standard Specification for
Joints for Concrete Pipe and Manholes, Using Rubber
1
Gaskets (Metric)
This standard is issued under the fixed designation C443M; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the U.S. Department of Defense.
1. Scope
1.1 This specification covers flexible leak-resistant joints for concrete pipe and precast manhole sections, using rubber gaskets
for sealing the joints, where infiltration or exfiltration is a factor in the design. The specification covers the design of joints and
the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specification C14M,
Specification C76M, or Specification C507M and precast manhole section conforming in all other respects to Specification
C478M, provided that if there is conflict in permissible variations in dimensions, the requirements of this specification for joints
shall govern.
1.2 This specification is the metric counterpart of Specification C443.
NOTE 1—This specification covers the design and performance of the rubber gasket joint only. Joints covered by this specification are adequate for
hydrostatic pressures up to 90 kPa (9 m), when tested per Section 9. Infiltration or exfiltration quantities for an installed pipeline are dependent upon many
factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system.
1.3 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C14M Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe (Metric)
C76M Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)
C478M Specification for Circular Precast Reinforced Concrete Manhole Sections (Metric)
C507M Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)
C822 Terminology Relating to Concrete Pipe and Related Products
C1619 Specification for Elastomeric Seals for Joining Concrete Structures
3. Terminology
3.1 Definitions—For definitions of terms relating to concrete pipe, see Terminology C822.
4. Basis of Acceptance
4.1 The acceptability of the pipe joints and gaskets shall be determined by the results of the physical tests prescribed in this
specification, if and when required, and by inspection to determine whether the pipe joints and gaskets conform to this specification
as to design and freedom from defects.
5. Materials and Manufacture for Gaskets
5.1 All rubber gaskets shall comply with Specification C1619 in terms of materials and manufacture. The gaskets shall be
extruded or molded to the specified size within a tolerance of 63 % on any dimension, measured at any cross section.
1
This specification is under the jurisdiction of ASTM Committee C13 on Concrete Pipe and is the direct responsibility of Subcommittee C13.08 on Joints for Precast
Concrete Structures.
Current edition approved May 1, 2019July 1, 2019. Published June 2019July 2019. Originally approved in 1980. Last previous edition approved in 20172019 as
C433M – 11C433M – 19.(2017). DOI: 10.1520/C0443M-19.10.1520/C0443M-19A.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C443M − 19a
6. Physical Requirements for Gaskets
6.1 Standard Gasket Requirements—All rubber gaskets shall meet the dimensions, tolerances, and physical requirements of
Specification C1619, Class C.
6.2 Oil Resistant Gasket Requirements—All rubber gaskets shall meet the dimensions, tolerances, and physical requirements of
Specification C1619, Class D.
7. Design of Joints
7.1 The manufactu
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.