ASTM D6450-12
(Test Method)Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
Standard Test Method for Flash Point by Continuously Closed Cup (CCCFP) Tester
SIGNIFICANCE AND USE
5.1 The flash point temperature is one measure of the tendency of the test specimen to form a flammable mixture with air under controlled laboratory conditions. It is only one of a number of properties that must be considered in assessing the overall flammability hazard of a material.
5.2 Flash point is used in shipping and safety regulations to define flammable and combustible materials and classify them. This definition may vary from regulation to regulation. Consult the particular regulation involved for precise definitions of these classifications.
5.3 This test method can be used to measure and describe the properties of materials in response to heat and an ignition source under controlled laboratory conditions and shall not be used to describe or appraise the fire hazard or fire risk of materials under actual fire conditions. However, results of this test method may be used as elements of a fire risk assessment, which takes into account all of the factors that are pertinent to an assessment of the fire hazard of a particular end use.
5.4 Flash point can also indicate the possible presence of highly volatile and flammable materials in a relatively nonvolatile or nonflammable material, such as the contamination of lubricating oils by small amounts of diesel fuel or gasoline.
SCOPE
1.1 This flash point test method is a dynamic method and depends on definite rates of temperature increase. It is one of the many flash point test methods available, and every flash point test method, including this one, is an empirical method.Note 1—Flash point values are not a constant physical-chemical property of materials tested. They are a function of the apparatus design, the condition of the apparatus used, and the operational procedure carried out. Flash point can therefore only be defined in terms of a standard test method, and no general valid correlation can be guaranteed between results obtained by different test methods or with test apparatus different from that specified.
1.2 This test method covers the determination of the flash point of fuel oils, lube oils, solvents, and other liquids by a continuously closed cup tester. The measurement is made on a test specimen of 1 mL.
1.3 This test method utilizes a closed but unsealed cup with air injected into the test chamber.
1.4 This test method is suitable for testing samples with a flash point from 10 to 250°C.Note 2—Flash point determinations below 10°C and above 250°C can be performed; however, the precision has not been determined below and above these temperatures.
1.5 If the user's specification requires a defined flash point method other than this test method, neither this test method nor any other method should be substituted for the prescribed method without obtaining comparative data and an agreement from the specifier.
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. Temperatures are in degrees Celsius, and pressure is in kilo-pascals.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific warning statements appear throughout the standard.
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation: D6450 − 12
StandardTest Method for
1
Flash Point by Continuously Closed Cup (CCCFP) Tester
This standard is issued under the fixed designation D6450; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* bility of regulatory limitations prior to use. Specific warning
statements appear throughout the standard.
1.1 This flash point test method is a dynamic method and
depends on definite rates of temperature increase. It is one of
2. Referenced Documents
the many flash point test methods available, and every flash
2
point test method, including this one, is an empirical method.
2.1 ASTM Standards:
D4057 Practice for Manual Sampling of Petroleum and
NOTE 1—Flash point values are not a constant physical-chemical
Petroleum Products
property of materials tested. They are a function of the apparatus design,
the condition of the apparatus used, and the operational procedure carried
D4177 Practice for Automatic Sampling of Petroleum and
out. Flash point can therefore only be defined in terms of a standard test
Petroleum Products
method, and no general valid correlation can be guaranteed between
D6299 Practice for Applying Statistical Quality Assurance
results obtained by different test methods or with test apparatus different
and Control Charting Techniques to Evaluate Analytical
from that specified.
Measurement System Performance
1.2 This test method covers the determination of the flash
D6300 Practice for Determination of Precision and Bias
point of fuel oils, lube oils, solvents, and other liquids by a
Data for Use in Test Methods for Petroleum Products and
continuously closed cup tester. The measurement is made on a
Lubricants
test specimen of 1 mL.
E300 Practice for Sampling Industrial Chemicals
1.3 This test method utilizes a closed but unsealed cup with
3
2.2 ISO Standards:
air injected into the test chamber.
ISO Guide 34 Quality Systems Guidelines for the Produc-
1.4 This test method is suitable for testing samples with a
tion of Reference Materials
flash point from 10 to 250°C.
ISOGuide35 CertificationsofReferenceMaterial–General
and Statistical Principles
NOTE 2—Flash point determinations below 10°C and above 250°C can
be performed; however, the precision has not been determined below and
above these temperatures.
3. Terminology
1.5 If the user’s specification requires a defined flash point
3.1 Definitions:
methodotherthanthistestmethod,neitherthistestmethodnor
3.1.1 dynamic, adj—the condition in which the vapor above
any other method should be substituted for the prescribed
the test specimen and the test specimen are not in temperature
method without obtaining comparative data and an agreement
equilibrium at the time at which the ignition source is applied.
from the specifier.
3.1.2 flash point, n—the lowest temperature corrected to a
1.6 The values stated in SI units are to be regarded as
pressure of 101.3 kPa at which application of an ignition
standard. No other units of measurement are included in this
source causes the vapors of a specimen of the sample to ignite
standard. Temperatures are in degrees Celsius, and pressure is
momentarily under specified conditions of the test.
in kilo-pascals.
3.1.2.1 Discussion—For the purpose of this test method, the
1.7 This standard does not purport to address all of the
test specimen is deemed to have flashed when the hot flame of
safety concerns, if any, associated with its use. It is the
the ignited vapor causes an instantaneous pressure increase of
responsibility of the user of this standard to establish appro-
at least 20 kPa inside the closed measuring chamber.
priate safety and health practices and determine the applica-
1 2
This test method is under the jurisdiction of ASTM Committee D02 on For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Petroleum Products and Lubricants and is the direct responsibility of Subcommittee contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
D02.08 on Volatility. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Dec. 1, 2012. Published March 2013. Originally the ASTM website.
3
approved in 1999. Last previous edition approved in 2010 as D6450–05 (2010). Available fromAmerican National Standards Institute (ANSI), 25 W. 43rd St.,
DOI: 10.1520/D6450-12. 4th Floor, New York, NY 10036.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D645
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6450 − 05 (Reapproved 2010) D6450 − 12
Standard Test Method for
1
Flash Point by Continuously Closed Cup (CCCFP) Tester
This standard is issued under the fixed designation D6450; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This flash point test method is a dynamic method and depends on definite rates of temperature increase. It is one of the many
flash point test methods available, and every flash point test method, including this one, is an empirical method.
NOTE 1—Flash point values are not a constant physical-chemical property of materials tested. They are a function of the apparatus design, the condition
of the apparatus used, and the operational procedure carried out. Flash point can therefore only be defined in terms of a standard test method, and no
general valid correlation can be guaranteed between results obtained by different test methods or with test apparatus different from that specified.
1.2 This test method covers the determination of the flash point of fuel oils, lube oils, solvents, and other liquids by a
continuously closed cup tester. The measurement is made on a test specimen of 1 mL.
1.3 This test method utilizes a closed but unsealed cup with air injected into the test chamber.
1.4 This test method is suitable for testing samples with a flash point from 10 to 250°C.
NOTE 2—Flash point determinations below 10°C and above 250°C can be performed; however, the precision has not been determined below and above
these temperatures.
1.5 If the user’s specification requires a defined flash point method other than this test method, neither this test method nor any
other method should be substituted for the prescribed method without obtaining comparative data and an agreement from the
specifier.
1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Temperatures are in degrees Celsius, and pressure is in kilo-pascals.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use. Specific warning statements appear throughout the standard.
2. Referenced Documents
2
2.1 ASTM Standards:
D4057 Practice for Manual Sampling of Petroleum and Petroleum Products
D4177 Practice for Automatic Sampling of Petroleum and Petroleum Products
D6299 Practice for Applying Statistical Quality Assurance and Control Charting Techniques to Evaluate Analytical Measure-
ment System Performance
D6300 Practice for Determination of Precision and Bias Data for Use in Test Methods for Petroleum Products and Lubricants
E300 Practice for Sampling Industrial Chemicals
3
2.2 ISO Standards:
ISO Guide 34 Quality Systems Guidelines for the Production of Reference Materials
ISO Guide 35 Certifications of Reference Material – General and Statistical Principles
3. Terminology
3.1 Definitions:
1
This test method is under the jurisdiction of ASTM Committee D02 on Petroleum Products and Lubricants and is the direct responsibility of Subcommittee D02.08 on
Volatility.
Current edition approved Oct. 1, 2010Dec. 1, 2012. Published November 2010March 2013. Originally approved in 1999. Last previous edition approved in 20052010 as
D6450–05. –05 (2010). DOI: 10.1520/D6450-05R10.10.1520/D6450-12.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6450 − 12
3.1.1 dynamic, adj—the condition in which the vapor above the test specimen and the test specimen are not in temperature
equilibrium at the time at which the ignition source is applied.
3.1.2 flash point, n—the lowest temperature corrected to a pressure of 101.3
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.