ASTM D3052-17
(Practice)Standard Practice for Rating Water-Emulsion Floor Polishes
Standard Practice for Rating Water-Emulsion Floor Polishes
SIGNIFICANCE AND USE
3.1 When comparing different floor polishes for an actual field performance, it is important that all surfaces used be prepared in the same way. When this procedure is followed, variations in the test surfaces are minimized.
SCOPE
1.1 This practice covers the comparison of the performance of water-emulsion floor polishes on test floors against a reference material. It is applicable to the following types of polishes:
1.1.1 Wax emulsion polishes,
1.1.2 Nonbuffable emulsion polishes,
1.1.3 Detergent-resistant emulsion polishes, household type, and
1.1.4 Detergent-resistant emulsion polishes, industrial type.
1.2 Gloss, leveling, discoloration, traffic marking, slip resistance, and removal ease of these types of floor polishes is rated in comparison to a reference material. Where applicable, detergent resistance is also evaluated. This method is not to be considered as a recommended maintenance procedure.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D3052 − 17
Standard Practice for
1
Rating Water-Emulsion Floor Polishes
This standard is issued under the fixed designation D3052; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This practice covers the comparison of the performance
D523Test Method for Specular Gloss
of water-emulsion floor polishes on test floors against a
2.2 CSMA Bulletin:
reference material. It is applicable to the following types of
245-70Comparative Determination of Slip Resistance of
polishes:
3
Floor Polishes
1.1.1 Wax emulsion polishes,
1.1.2 Nonbuffable emulsion polishes,
3. Significance and Use
1.1.3 Detergent-resistantemulsionpolishes,householdtype,
3.1 When comparing different floor polishes for an actual
and
field performance, it is important that all surfaces used be
1.1.4 Detergent-resistant emulsion polishes, industrial type. prepared in the same way. When this procedure is followed,
variations in the test surfaces are minimized.
1.2 Gloss, leveling, discoloration, traffic marking, slip
resistance, and removal ease of these types of floor polishes is
4. Apparatus
rated in comparison to a reference material. Where applicable,
4
4.1 Test Tile, OVCT.
detergent resistance is also evaluated. This method is not to be
4.2 Glossmeter, 60°—The instrument and the reference
considered as a recommended maintenance procedure.
standards shall conform to the requirements prescribed in Test
1.3 The values stated in inch-pound units are to be regarded
Method D523, using an angle of reflection of 60°.
as the standard. The values given in parentheses are for
4.3 Floor Machine.
information only.
5. Procedure
1.4 The values stated in inch-pound units are to be regarded
as standard. The values given in parentheses are mathematical 5.1 The preferred substrate shall be Official Vinyl Compo-
conversions to SI units that are provided for information only sition Tile.
and are not considered standard.
5.2 The test floor shall include both dark (black) and light
(white) colored tiles laid out so that one half of the panel is all
1.5 This standard does not purport to address all of the
white and the other half is all black.
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appro-
5.3 Theminimumtestpanelsizeforeachpolishtestedshall
priate safety and health practices and determine the applica- be 3 ft (0.9 m) in width and 3 ft in length.
bility of regulatory limitations prior to use.
5.4 Prepare all of the test panels with scrub-cleaned new
1.6 This international standard was developed in accor-
tiles, or strip completely of dirt and old wax, rinse thoroughly
dance with internationally recognized principles on standard-
and dry before application of the test polishes. Under no
ization established in the Decision on Principles for the
Development of International Standards, Guides and Recom-
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
mendations issued by the World Trade Organization Technical
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Barriers to Trade (TBT) Committee.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
Available from the Chemical Specialties Manufacturers Association, 1001
Connecticut Avenue, NW, Washington, DC 20036.
1 4
This practice is under the jurisdiction of ASTM Committee D21 on Polishes OVCT tile may be obtained through Armstrong Flooring from various home
and is the direct responsibility of Subcommittee D21.04 on Performance Tests. improvement stores. The following Armstrong tile substrates have been found to
Current edition approved March 1, 2017. Published April 2017. Originally perform adequately for this test method: Armstrong Excelon Feature Tile: Black
approved in 1972. Last previous edition approved in 2010 as D3052–87 (2010). (56790), http://www.armstrong.com/commflooringna/product_details_toolbox_
DOI: 10.1520/D3052-17. magnify.jsp?item_id=47394.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3052 − 17
circumstancesshouldcomparativetestsbemadeonnewversus necessitate longer periods of drying time.) Again take gloss
old tiles. Similarly, where old tiles are employed, care should readings on the four
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D3052 − 87 (Reapproved 2010) D3052 − 17
Standard Practice for
1
Rating Water-Emulsion Floor Polishes
This standard is issued under the fixed designation D3052; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This practice covers the comparison of the performance of water-emulsion floor polishes on test floors against a reference
material. It is applicable to the following types of polishes:
1.1.1 Wax emulsion polishes,
1.1.2 Nonbuffable emulsion polishes,
1.1.3 Detergent-resistant emulsion polishes, household type, and
1.1.4 Detergent-resistant emulsion polishes, industrial type.
1.2 Gloss, leveling, discoloration, traffic marking, slip resistance, and removal ease of these types of floor polishes is rated in
comparison to a reference material. Where applicable, detergent resistance is also evaluated. This method is not to be considered
as a recommended maintenance procedure.
1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information
only.
1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only and are not considered standard.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory
limitations prior to use.
1.6 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
D523 Test Method for Specular Gloss
2.2 CSMA Bulletin:
3
245-70 Comparative Determination of Slip Resistance of Floor Polishes
3. Significance and Use
3.1 When comparing different floor polishes for an actual field performance, it is important that all surfaces used be prepared
in the same way. When this procedure is followed, variations in the test surfaces are minimized.
4. Apparatus
4
4.1 Test Tile, OVCT.
1
This practice is under the jurisdiction of ASTM Committee D21 on Polishes and is the direct responsibility of Subcommittee D21.04 on Performance Tests.
Current edition approved May 1, 2010March 1, 2017. Published May 2010April 2017. Originally approved in 1972. Last previous edition approved in 20032010 as
D3052 – 87 (2003).(2010). DOI: 10.1520/D3052-87R10.10.1520/D3052-17.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from the Chemical Specialties Manufacturers Association, 1001 Connecticut Avenue, NW, Washington, DC 20036.
4
Official Vinyl Composition Tile (OVCT) is available from the Chemical Specialties Manufacturers Association, 1001 Connecticut Avenue, NW, Wash- ington, DC
20036.OVCT tile may be obtained through Armstrong Flooring from various home improvement stores. The following Armstrong tile substrates have been found to perform
adequately for this test method: Armstrong Excelon Feature Tile: Black (56790), http://www.armstrong.com/commflooringna/product_details_toolbox_magnify.jsp?item_
id=47394.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D3052 − 17
4.2 Glossmeter, 60°—The instrument and the reference standards shall conform to the requirements prescribed in Test Method
D523, using an angle of reflection of 60°.
4.3 Floor Machine.
5. Procedure
5.1 The preferred substrate shall be Official Vinyl Composition Tile.
5.2 The test floor shall include both dark (black) and light (white) colored tiles laid out so that one half of the panel is all white
and the other half is all black.
5.3 The minimum test panel size for each polish tested shall be 3 ft (0.9 m) in width and 3 ft in length.
5.4 Prepa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.