ASTM A860/A860M-18

Standard Specification for Wrought High-Strength Ferritic Steel Butt-Welding Fittings

ABSTRACT
This specification covers wrought high-strength low-alloy butt-welding steel fittings of seamless and electric fusion-welded construction for applications in high-pressure gas and oil transmission and distribution systems. Starting materials shall consist of plate, sheet, forgings, forging quality bar, and seamless or fusion-welded tubular products with filler metal added. Materials shall be heat treated by normalizing, quenching, and tempering or stress relieving. Specimens shall conform to required values of chemical composition and mechanical properties, namely: yield strength, tensile strength, elongation, notch toughness, and hardness. This specification does not require hydrostatic testing.
SCOPE
1.1 This specification covers wrought high-strength ferritic steel butt-welding fittings of seamless and electric fusion-welded construction. Dimensions of the fittings are provided in the latest revisions of ASME B16.9 and MSS-SP-75. Butt-welding fittings differing from ASME B16.9 shall be furnished in accordance with Supplementary Requirement S58 of Specification A960/A960M. These fittings are for use in high-pressure gas and oil transmission and distribution systems.  
1.2 Optional supplementary requirements are provided for fittings when a greater degree of examination is desired. One or more of the supplementary requirements may be specified in the order.  
1.3 This specification does not cover cast-welding fittings or fittings machined from castings.  
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.  
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

General Information

• Status: Historical
• Publication Date: 30-Apr-2018
• ICS: 23.040.40 - Metal fittings
• Technical Committee: A01 - Steel, Stainless Steel and Related Alloys
• Drafting Committee: A01.22 - Steel Forgings and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:A860/A860M −18
Standard Specification for
1
Wrought High-Strength Ferritic Steel Butt-Welding Fittings
This standard is issued under the fixed designationA860/A860M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 2. Referenced Documents
2
2.1 ASTM Standards:
1.1 This specification covers wrought high-strength ferritic
A751Test Methods, Practices, and Terminology for Chemi-
steel butt-welding fittings of seamless and electric fusion-
cal Analysis of Steel Products
weldedconstruction.Dimensionsofthefittingsareprovidedin
A960/A960MSpecification for Common Requirements for
the latest revisions of ASME B16.9 and MSS-SP-75. Butt-
Wrought Steel Piping Fittings
welding fittings differing fromASME B16.9 shall be furnished
3
2.2 ASME Standards:
in accordance with Supplementary Requirement S58 of Speci-
B16.9Steel Butt-Welding Fittings
fication A960/A960M. These fittings are for use in high-
3
2.3 ASME Boiler and Pressure Vessel Code:
pressure gas and oil transmission and distribution systems.
Section V
1.2 Optional supplementary requirements are provided for
Section VIIIDivision 1
fittingswhenagreaterdegreeofexaminationisdesired.Oneor
Section IX
4
more of the supplementary requirements may be specified in
2.4 MSS Standards:
the order.
MSS SP-25 The Standard Marking System of Valves,
Fittings, Flanges and Unions
1.3 Thisspecificationdoesnotcovercast-weldingfittingsor
MSS-SP-75 Specification for High Test Wrought Butt-
fittings machined from castings.
Welding Fittings
1.4 The values stated in either SI units or inch-pound units 5
2.5 American Society of Nondestructive Testing:
are to be regarded separately as standard. Within the text, the
SNT-TC-1A Recommended Practice for Nondestructive
SI units are shown in brackets. The values stated in each
Testing Personnel Qualification and Certification
system may not be exact equivalents; therefore, each system
3. Ordering Information
shall be used independently of the other. Combining values
from the two systems may result in non-conformance with the
3.1 In addition to the requirements of Specification A960/
standard. Unless the order specifies the applicable “M” speci-
A960M, the following ordering information applies:
fication designation (SI units), the material shall be furnished
3.1.1 Grade Symbol,
to inch-pound units.
3.1.2 Requirements for certification of test report.
1.5 This international standard was developed in accor-
4. General Requirements
dance with internationally recognized principles on standard-
4.1 Product furnished to this specification shall conform to
ization established in the Decision on Principles for the
the requirements of Specification A960/A960M, including any
Development of International Standards, Guides and Recom-
mendations issued by the World Trade Organization Technical
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
Barriers to Trade (TBT) Committee.
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.
3
Available from American Society of Mechanical Engineers (ASME), ASME
1
This specification is under the jurisdiction ofASTM Committee A01 on Steel, International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee www.asme.org.
4
A01.22 on Steel Forgings andWrought Fittings for PipingApplications and Bolting AvailablefromManufacturersStandardizationSocietyoftheValveandFittings
Materials for Piping and Special Purpose Applications. Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http://www.mss-
Current edition approved May 1, 2018. Published May 2018. Originally hq.com.
5
approved in 1986. Last previous edition approved in 2014 as A860/A860M–14. AvailablefromAmericanSocietyforNondestructiveTesting(ASNT),P.O.Box
DOI: 10.1520/A0860_A0860M-18. 28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http://www.asnt.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A860/A860M−18
supplementary requirements that are indicated in the purchase 5.6.1 Made by welders, welding operators, and welding
order. Failure to comply with the general requirements of procedures qualified under the provisions ofASME Boiler and
Specification A960/A960M constitutes nonconformance with Pressure Vessel Code, Section IX.
this specifi
...

This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: A860/A860M − 14 A860/A860M − 18
Standard Specification for
1
Wrought High-Strength Ferritic Steel Butt-Welding Fittings
This standard is issued under the fixed designation A860/A860M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope*
1.1 This specification covers wrought high-strength ferritic steel butt-welding fittings of seamless and electric fusion-welded
construction covered by the construction. Dimensions of the fittings are provided in the latest revisions of ASME B16.9 and
MSS-SP-75. Butt-welding fittings differing from these ASME and MSS standards ASME B16.9 shall be furnished in accordance
with Supplementary Requirement S58 of Specification A960/A960M. These fittings are for use in high-pressure gas and oil
transmission and distribution systems.
1.2 Optional supplementary requirements are provided for fittings when a greater degree of examination is desired. One or more
of the supplementary requirements may be specified in the order.
1.3 This specification does not cover cast-welding fittings or fittings machined from castings.
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units
are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used
independently of the other. Combining values from the two systems may result in non-conformance with the standard. Unless the
order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A960/A960M Specification for Common Requirements for Wrought Steel Piping Fittings
3
2.2 ASME Standards:
B16.9 Steel Butt-Welding Fittings
3
2.3 ASME Boiler and Pressure Vessel Code:
Section V
Section VIII Division 1
Section IX
4
2.4 MSS Standards:
MSS SP-25 The Standard Marking System of Valves, Fittings, Flanges and Unions
MSS-SP-75 Specification for High Test Wrought Butt-Welding Fittings
5
2.5 American Society of Nondestructive Testing:
SNT-TC-1A Recommended Practice for Nondestructive Testing Personnel Qualification and Certification
1
This specification is under the jurisdiction of ASTM Committee A01 on Steel, Stainless Steel and Related Alloysand is the direct responsibility of Subcommittee A01.22
on Steel Forgings and Wrought Fittings for Piping Applications and Bolting Materials for Piping and Special Purpose Applications.
Current edition approved Oct. 1, 2014May 1, 2018. Published October 2014May 2018. Originally approved in 1986. Last previous edition approved in 20132014 as
A860/A860MA860/A860M – 14.–13. DOI: 10.1520/A0860_A0860M-14.10.1520/A0860_A0860M-18.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Two Park Ave., New York, NY 10016-5990, http://
www.asme.org.
4
Available from Manufacturers Standardization Society of the Valve and Fittings Industry (MSS), 127 Park St., NE, Vienna, VA 22180-4602, http://www.mss-hq.com.
5
Available from American Society for Nondestructive Testing (ASNT), P.O. Box 28518, 1711 Arlingate Ln., Columbus, OH 43228-0518, http://www.asnt.org.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
A860/A860M − 18
3. Ordering Information
3.1 In addition to the requirements of Specification A960/A960M, the following ordering information applies:
3.1.1 Grade Symbol,
3.1.2 Requirements for certification of test report.
4. General Requir
...