ASTM F1005-91(2019)
(Practice)Standard Practice for HVAC Duct Shapes; Identification and Description of Design Configuration
Standard Practice for HVAC Duct Shapes; Identification and Description of Design Configuration
SIGNIFICANCE AND USE
3.1 Standard nomenclature shall be used to facilitate communication between designers, suppliers, and users of HVAC ventilation ductwork components.
3.2 Standard design parameters shall be used to define ventilation ductwork shapes.
3.3 Standard variables for design parameters (see 2.2) are useful in writing CAD/CAM software for automatic fabrication of ventilation ductwork shapes.
SCOPE
1.1 This practice covers the identification of design configurations and descriptive nomenclature for sheetmetal HVAC ductwork shapes frequently used in shipbuilding. This practice also covers parametric dimensions of these shapes. (See Table 1.)
1.2 This practice does not cover the location of seams or joints within a shape or the method of joining shapes together.
1.3 Since this practice is not measurement sensitive, it is applicable whether inch-pound or SI metric dimensions are used.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation:F1005 −91 (Reapproved 2019) An American National Standard
Standard Practice for
HVAC Duct Shapes; Identification and Description of Design
1
Configuration
This standard is issued under the fixed designation F1005; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2.1.5 offset, n—fitting that changes the location of the duct
with the line of the duct remaining parallel.
1.1 This practice covers the identification of design configu-
2.1.6 ogee, n—a smoothly curved type of offset. The inside
rations and descriptive nomenclature for sheetmetal HVAC
curve of each end is tangent to the outside curve of the other
ductwork shapes frequently used in shipbuilding. This practice
end.
also covers parametric dimensions of these shapes. (See Table
1.)
2.1.7 radius corner, n—cross section that is generally
rectangular, but with the corners softened to a radius.
1.2 This practice does not cover the location of seams or
joints within a shape or the method of joining shapes together. 2.1.8 rectangular, n—rectangular or square cross section.
2.1.9 reducer, n—a fitting that changes the size but not the
1.3 Since this practice is not measurement sensitive, it is
cross-section type of duct.
applicable whether inch-pound or SI metric dimensions are
used.
2.1.10 round, n—circular cross section.
1.4 This standard does not purport to address all of the
2.1.11 short axis of flat oval, n—curved so that the flat sides
safety concerns, if any, associated with its use. It is the
of the flat oval correspond to the curve.
responsibility of the user of this standard to establish appro-
2.1.12 splitter, n—internal part of some elbows and offsets;
priate safety, health, and environmental practices and deter-
sometimes required in diverging transitions. Used to provide
mine the applicability of regulatory limitations prior to use.
more uniform velocity and distribution of air flow.The number
1.5 This international standard was developed in accor-
and location of splitters is determined by calculation or from a
dance with internationally recognized principles on standard-
nomograph.
ization established in the Decision on Principles for the
2.1.13 straight, n—duct that remains constant in cross
Development of International Standards, Guides and Recom-
section and size throughout its length.
mendations issued by the World Trade Organization Technical
2.1.14 throat, n—wrapper around the inside of a fitting.
Barriers to Trade (TBT) Committee.
2.1.15 transition, n—fitting that changes the cross-section
2. Terminology
type of the duct.
2.1 Definitions of Terms Specific to This Standard:
2.1.16 vane, n—internal part of vaned turns. Used to pro-
2.1.1 branch, n—portion of a duct system connection to a vide more uniform velocity of air flow. Configuration, number,
main duct. and location of vanes is determined from drawing, NAVSHIPS
2
No. S3801-385260. The direction of airflow must be marked
2.1.2 elbow, n—a fitting used to change direction of air
on vaned turns.
flow.
2.1.17 vaned turn, n—a fitting containing vanes that is used
2.1.3 flat oval, n—cross section that has flat sides and
to change the direction of air flow.
semicircular ends.
2.2 Variables Specific to This Standard:
2.1.4 longaxisofflatoval,n—curvedsothattheflatsidesof
A—Angle. Included angle of an elbow, branch, vaned turn,
the flat oval remain in a plane.
or slant-top fitting.
AI—Air In indicates the length of the straight portion of a
vaned turn in the “air in-flow” side.
1
This practice is under the jurisdiction of ASTM Committee F25 on Ships and
Marine Technology and is the direct responsibility of Subcommittee F25.11 on
2
Machinery and Piping Systems. Drawing: Naval Sea Systems Command (NAVSEA) NAVSHIPS S3801-
Current edition approved Dec. 1, 2019. Published January 2020. Originally 385260 Vanes Channels Ventilation Vane, available from Commander, Portsmouth
approved in 1986. Last previous edition approved in 2013 as F1005 – 91 (2013). Naval Shipyard, Naval Engineering Drawing Support Activity, Code 202.2,
DOI: 10.1520/F1005-91R19. Portsmouth, NH 03804-5000.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
F1005−91 (2019)
TABLE 1 HVAC Standard Nomenclature and Numbering System
1.1—Major length of a Y branch.
1. Straight: 1.2—Minor length of a Y branch.
1.1 Straight-round
O—Offset in one direction.
1.2 Stra
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.