ASTM F782-01

Standard Specification for Doors, Furniture, Marine

SCOPE
1.1 This specification covers the construction of furniture doors for use where invoked by other marine furniture specifications.  
1.2 This specification applies to all furniture doors for marine furniture, in items requiring hinged doors.  
1.3 Values stated in inch-pound units are to be regarded as the standard. The metric equivalents, given in parentheses, are for information only.

General Information

• Status: Historical
• Publication Date: 09-Jun-2001
• ICS: 47.020.80 - Accommodation spaces
• Technical Committee: F25 - Ships and Marine Technology
• Drafting Committee: F25.03 - Outfitting and Deck Machinery

Relations

• Replaces: ASTM F782-95 - Standard Specification for Doors, Furniture, Marine
• Effective Date: 10-Jun-2001
• Replaced By: ASTM F782-01(2007) - Standard Specification for Doors, Furniture, Marine
• Effective Date: 01-May-2007
• Referred By: ASTM F823-22 - Standard Specification for Desk, Log, Marine, Steel, with Cabinet
• Effective Date: 10-Jun-2001

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
An American National Standard
Designation: F 782 – 01
Standard Specification for
1
Doors, Furniture, Marine
This standard is issued under the fixed designation F 782; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
1. Scope in Decimals of an Inch, U.S. Standard Gage (USSG) for
Uncoated Hot and Cold-Rolled Sheets
1.1 This specification covers the construction of furniture
8
2.3 Federal Specifications:
doors for use where invoked by other marine furniture speci-
DD-G-1403 Glass, Plate (Float), Sheet Figured, and Span-
fications.
drel (Heat Strengthened and Fully Tempered)
1.2 This specification applies to all furniture doors for
LP-391 Plastic Sheets, Rods and Tubing, Rigid Cast, Meth-
marine furniture, in items requiring hinged doors.
acrylate (Multiapplication)
1.3 Values stated in inch-pound units are to be regarded as
QQ-C-320 Chromium Plating (Electrodeposited)
the standard. The metric equivalents, given in parentheses, are
QQ-Z-325 Zinc Coating, Electrodeposited
for information only.
9
2.4 American National Standard Institute Standards:
2. Referenced Documents
ANSI Z97.1-1975 Safety Performance Specifications and
Methods of Test for Safety Glazing Material Used in
2.1 ASTM Standards:
Buildings
A 240 Specification for Heat-Resisting Chromium and
Chromium-Nickel Stainless Steel Plate, Sheet, and Strip
3. Terminology
2
for Pressure Vessels
3.1 Definitions of Terms Specific to This Standard:
A 1008/A 1008M Specification for Steel, Sheet, Cold-
3.1.1 flush doors—metaldoorswithasmoothsurfaceonthe
Rolled, Carbon, Structural, High-Strength Low-Alloy and
2
exterior face.
High-Strength Low-Alloy with Improved Formability
3.1.2 hinged door—doorequippedwithhingesthatpermitit
A 582/A 582M Specification for Free-Machining Stainless
3
to swing about the vertical hinge axis, either right hand or left
Steel Bars
hand.
B 209 Specification for Aluminum and Aluminum-Alloy
4 3.1.2.1 right-hand door—door with hinges on the right side
Sheet and Plate
when viewed from the exterior of the furniture item containing
B 221 Specification for Aluminum and Aluminum-Alloy
4 the door.
Extruded Bars, Rods, Wire, Profiles, and Tubes
5
3.1.2.2 left-hand door—door with hinges on the left side
C 1036 Specification for Flat Glass
6 when viewed from the exterior of the furniture item containing
D 907 Terminology of Adhesives
7
the door.
2.2 American Institute of Steel Construction Manual:
3.1.3 panel doors—doors with metal stiles and rails that
AISC Wire and Sheet Metal Gages—Equivalent Thickness
supportapanelinsertoftransparentsafetyglazingorexpanded
aluminum.
1
This specification is under the jurisdiction of ASTM Committee F25 on Ships
3.1.3.1 stiles—the vertical members in the frame of a panel
and Marine Technology and is the direct responsibility of Subcommittee F25.03 on
door that support the central panel.
Outfitting.
3.1.3.2 rails—the horizontal members in the frame of a
Current edition approved June 10, 2001. Published September 2001. Originally
panel door that support the central panel.
published as F 782 – 82. Last previous revision F 782 – 94.
2
Annual Book of ASTM Standards, Vol 01.03.
3
Annual Book of ASTM Standards, Vol 01.05.
4
Annual Book of ASTM Standards, Vol 02.02.
5 8
Annual Book of ASTM Standards, Vol 15.02. AvailablefromStandardizationDocumentsOrderDesk,Bldg.4SectionD,700
6
Annual Book of ASTM Standards, Vol 15.06. Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.
7 9
Available from the American Institute of Steel Construction, 400 N. Michigan AvailablefromAmericanNationalStandardsInstitute,25W.43rdSt.,4thFloor,
Ave., Chicago, IL 60611. New York, NY 10036.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
1

---------------------- Page: 1 ----------------------
F 782
4. Classification 5.1.3.2 Manufacturer’s standard baked enamel will be fur-
nished unless otherwise required and indicated by the pur-
4.1 Doors shall be of the following types as required by the
chaser.
specifications for the item of furniture in which they are
5.1.4 For single-hinged doors, indicate hand if not obvious
installed and as indicated in ordering documents. See Fig. 1 for
or if a specific hand is required.
details.
5.1.5 Material for Type II (panel) doors may be either steel
4.1.1 Type I—Flush hinged door.
or aluminum. Material selected shall be the option of the
4.1.2 Type II—Panel hinged door.
furniture purchaser.
5. Ordering Information
6. Materials and Manufacture
5.1 Doors are included as part of
...