ASTM F782-95
(Specification)Standard Specification for Doors, Furniture, Marine
Standard Specification for Doors, Furniture, Marine
SCOPE
1.1 This specification covers the construction of furniture doors for use where invoked by other marine furniture specifications.
1.2 This specification applies to all furniture doors for marine furniture, in items requiring hinged doors.
1.3 Values stated in inch-pound units are to be regarded as the standard. The metric equivalents, given in parentheses, are for information only.
General Information
Relations
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or
withdrawn. Contact ASTM International (www.astm.org) for the latest information.
Designation: F 782 – 95 An American National Standard
AMERICAN SOCIETY FOR TESTING AND MATERIALS
100 Barr Harbor Dr., West Conshohocken, PA 19428
Reprinted from the Annual Book of ASTM Standards. Copyright ASTM
Standard Specification for
1
Doors, Furniture, Marine
This standard is issued under the fixed designation F 782; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense. Consult the DoD Index of Specifications and
Standards for the specific year of issue which has been adopted by the Department of Defense.
1. Scope LP-391 Plastic Sheets, Rods and Tubing, Rigid Cast, Meth-
acrylate (Multiapplication)
1.1 This specification covers the construction of furniture
QQ-C-320 Chromium Plating (Electrodeposited)
doors for use where invoked by other marine furniture speci-
QQ-Z-325 Zinc Coating, Electrodeposited
fications.
9
2.4 American National Standard Institute Standards:
1.2 This specification applies to all furniture doors for
ANSI Z97.1-1975 Safety Performance Specifications and
marine furniture, in items requiring hinged doors.
Methods of Test for Safety Glazing Material Used in
1.3 Values stated in inch-pound units are to be regarded as
Buildings
the standard. The metric equivalents, given in parentheses, are
for information only.
3. Terminology
2. Referenced Documents 3.1 Descriptions of Terms Specific to This Standard:
3.1.1 flush doors—metal doors with a smooth surface on the
2.1 ASTM Standards:
exterior face.
A 240 Specification for Heat-Resisting Chromium and
3.1.2 hinged door—door equipped with hinges that permit it
Chromium-Nickel Stainless Steel Plate, Sheet, and Strip
2 to swing about the vertical hinge axis, either right hand or left
for Pressure Vessels
hand.
A 366/A 366M Specification for Steel, Sheet, Carbon,
2 3.1.2.1 right-hand door—door with hinges on the right side
Cold-Rolled, Commercial Quality
when viewed from the exterior of the furniture item containing
A 582 Specification for Free-Machining Stainless and Heat-
3
the door.
Resisting Steel Bars, Hot-Rolled or Cold-Finished
3.1.2.2 left-hand door—door with hinges on the left side
B 209 Specification for Aluminum and Aluminum-Alloy
4
when viewed from the exterior of the furniture item containing
Sheet and Plate
the door.
B 221 Specification for Aluminum and Aluminum-Alloy
4
3.1.3 panel doors—doors with metal stiles and rails that
Extruded Bars, Rods, Wire, Shapes, and Tubes
5
support a panel insert of transparent safety glazing or expanded
C 1036 Specification for Flat Glass
6
aluminum.
D 907 Terminology of Adhesives
7
3.1.3.1 stiles—the vertical members in the frame of a panel
2.2 American Institute of Steel Construction Manual:
door that support the central panel.
AISC Wire and Sheet Metal Gages—Equivalent Thickness
3.1.3.2 rails—the horizontal members in the frame of a
in Decimals of an Inch, U.S. Standard Gage (USSG) for
panel door that support the central panel.
Uncoated Hot and Cold-Rolled Sheets
8
2.3 Federal Specifications:
4. Classification
DD-G-1403 Glass, Plate (Float), Sheet Figured, and Span-
4.1 Doors shall be of the following types as required by the
drel (Heat Strengthened and Fully Tempered)
specifications for the item of furniture in which they are
installed and as indicated in ordering documents. See Fig. 1 for
1
This specification is under the jurisdiction of ASTM Committee F-25 on
details.
Shipbuilding and is the direct responsibility of Subcommittee F25.03 on Outfitting.
4.1.1 Type I—Flush hinged door.
Current edition approved Feb. 15, 1995. Published April 1995. Originally
published as F 782 – 82. Last previous revision F 782 – 94.
4.1.2 Type II—Panel hinged door.
2
Annual Book of ASTM Standards, Vol 01.03.
3
Annual Book of ASTM Standards, Vol 01.05.
5. Ordering Information
4
Annual Book of ASTM Standards, Vol 02.02.
5
5.1 Doors are included as part of the orders for items of
Annual Book of ASTM Standards, Vol 15.02.
6
Annual Book of ASTM Standards, Vol 15.06.
furniture requiring doors. To describe adequately the door or
7
Available from the American Institute of Steel Construction, 400 N. Michigan
Ave., Chicago, IL 60611.
8 9
Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Available from American National Standards Institute, 11 W. 42nd St., 13th
Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS. Floor, New York, NY 10036.
1
---------------------- Page: 1 ----------------------
F 782
TABLE 1 Table of Dimensions
Dimensions
Designation
in. mm
Door thickness A 1 max 25.4 max
Width of stile or height of rail B 3 ma
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.