ASTM D3035-12e1

Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter

ABSTRACT
This specification covers polyethylene (PE) pipes made in thermoplastic pipe dimension ratios based on outside diameter, and pressure rated for water. All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents, slurries, municipal sewage, etc. Included are criteria for classifying PE plastic pipe materials and PE plastic pipe, and a system of nomenclature for PE plastic pipe. PE pipes shall be evaluated by the test procedures given herein, and shall conform to specified requirements for workmanship, dimensions, sustained pressure at ambient and elevated temperatures, hydrostatic burst pressure, tensile strength at yield, and environmental stress cracking.
SCOPE
1.1 This specification covers polyethylene (PE) pipe made in thermoplastic pipe dimension ratios based on outside diameter and pressure rated for water (see Appendix X1). Included are requirements for polyethylene compounds and PE plastic pipe, a system of nomenclature for PE plastic pipe, and requirements and test methods for materials, workmanship, dimensions, sustained pressure, and burst pressure. Methods of marking are also given.  
1.2 All pipes produced under this specification may be used for the transport of water, industrial process liquids, effluents, slurries, municipal sewage, etc. The user should consult the manufacturer to determine whether the material being transported is compatible with polyethylene pipe and will not affect the service life beyond limits acceptable to the user.  
1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.  
1.4 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

General Information

• Status: Historical
• Publication Date: 30-Jun-2012
• ICS: 23.040.20 - Plastics pipes
• Technical Committee: F17 - Plastic Piping Systems
• Drafting Committee: F17.26 - Olefin Based Pipe

Relations

• Replaces: ASTM D3035-12 - Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
• Effective Date: 01-Jul-2012
• Replaced By: ASTM D3035-12e2 - Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
• Effective Date: 01-Jul-2012
• Referred By: ASTM F714-22 - Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
• Effective Date: 01-Jul-2012
• Referred By: ASTM F2880-21 - Standard Specification for Lap-Joint Type Flange Adapters for Polyethylene Pressure Pipe in Nominal Pipe Sizes <fraction><num>3</num><den>4</den></fraction > in. to 65 in.
• Effective Date: 01-Jul-2012
• Referred By: ASTM D3350-21 - Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
• Effective Date: 01-Jul-2012
• Referred By: ASTM D2683-20 - Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
• Effective Date: 01-Jul-2012
• Referred By: ASTM F3632-23 - Standard Practice for Close Tolerance Pipe Slurrification (CTPS) Method to Replace, Rehabilitate, and Repair Existing Buried Asbestos Cement (AC) Pipe Systems
• Effective Date: 01-Jul-2012
• Referred By: ASTM F1759-97(2018) - Standard Practice for Design of High-Density Polyethylene (HDPE) Manholes for Subsurface Applications
• Effective Date: 01-Jul-2012
• Referred By: ASTM F3123-22 - Standard Specification for Metric Outside Diameter Polyethylene (PE) Plastic Pipe (DR-PN)
• Effective Date: 01-Jul-2012
• Referred By: ASTM F1056-18(2022) - Standard Specification for Socket Fusion Tools for Use in Socket Fusion Joining Polyethylene Pipe or Tubing and Fittings
• Effective Date: 01-Jul-2012
• Referred By: ASTM F3565-23 - Standard Practice for Electrofusion Joining Polyethylene (PE) Pipe and Fittings for Pressure Pipe Service
• Effective Date: 01-Jul-2012
• Referred By: ASTM F3508-21a - Standard Guide for In-Situ Pipeline Renovation As Dual-Wall Composite Pipeline by Push/Pull Installation of Compressed-Fit Shape-Memory-Polymer Tubular (SMPT)
• Effective Date: 01-Jul-2012
• Referred By: ASTM F3536-22 - Standard Specification for PE and PP Mechanical Fittings for use on NPS 3 or Smaller Cold-water Service Polyethylene (PE) or Crosslinked Polyethylene (PEX) Pipe or Tubing
• Effective Date: 01-Jul-2012
• Referred By: ASTM F2165-19 - Standard Specification for Flexible Pre-Insulated Plastic Piping
• Effective Date: 01-Jul-2012
• Referred By: ASTM F2206-19 - Standard Specification for Fabricated Fittings of Butt-Fused Polyethylene (PE)
• Effective Date: 01-Jul-2012

Standards Content (Sample)

NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
´1
Designation:D3035 −12 AnAmerican National Standard
Standard Specification for
Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled
1
Outside Diameter
This standard is issued under the fixed designation D3035; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1 E
ε NOTE—Editorially corrected Table 1. Removed blank footnote in November 2012.
1. Scope* D1238 Test Method for Melt Flow Rates of Thermoplastics
by Extrusion Plastometer
1.1 This specification covers polyethylene (PE) pipe made
D1598 Test Method for Time-to-Failure of Plastic Pipe
in thermoplastic pipe dimension ratios based on outside diam-
Under Constant Internal Pressure
eter and pressure rated for water (see Appendix X1). Included
D1599 Test Method for Resistance to Short-Time Hydraulic
are requirements for polyethylene compounds and PE plastic
Pressure of Plastic Pipe, Tubing, and Fittings
pipe, a system of nomenclature for PE plastic pipe, and
D1600 Terminology forAbbreviatedTerms Relating to Plas-
requirements and test methods for materials, workmanship,
tics
dimensions, sustained pressure, and burst pressure. Methods of
D1603 Test Method for Carbon Black Content in Olefin
marking are also given.
Plastics
1.2 All pipes produced under this specification may be used
D2122 Test Method for Determining Dimensions of Ther-
for the transport of water, industrial process liquids, effluents,
moplastic Pipe and Fittings
slurries, municipal sewage, etc. The user should consult the
D2290 Test Method for Apparent Hoop Tensile Strength of
manufacturer to determine whether the material being trans-
Plastic or Reinforced Plastic Pipe
ported is compatible with polyethylene pipe and will not affect
D2837 Test Method for Obtaining Hydrostatic Design Basis
the service life beyond limits acceptable to the user.
forThermoplasticPipeMaterialsorPressureDesignBasis
1.3 The values stated in inch-pound units are to be regarded for Thermoplastic Pipe Products
D3350 Specification for Polyethylene Plastics Pipe and Fit-
as standard. The values given in parentheses are mathematical
conversions to SI units that are provided for information only tings Materials
and are not considered standard. D4218 Test Method for Determination of Carbon Black
Content in Polyethylene Compounds By the Muffle-
1.4 The following safety hazards caveat pertains only to the
Furnace Technique
test methods portion, Section 7, of this specification:This
F412 Terminology Relating to Plastic Piping Systems
standard does not purport to address all of the safety concerns,
2.2 NSF International Standards:
if any, associated with its use. It is the responsibility of the user
NSF/ANSI Standard No. 14 for Plastic Piping Components
of this standard to establish appropriate safety and health
3
and Related Materials
practices and determine the applicability of regulatory limita-
NSF/ANSI Standard No. 61 for Drinking Water System
tions prior to use.
3
Components—Health Effects
2. Referenced Documents
2.3 Other Documents:
2
TR-4 Listing of Hydrostatic Design Bases (HDB), Strength
2.1 ASTM Standards:
Design Bases (SDB), Pressure Design Bases (PDB) and
D618 Practice for Conditioning Plastics for Testing
Minimum Required Strength (MRS) Ratings for Thermo-
4
plastic Piping Materials or Pipe
1 5
This specification is under the jurisdiction ofASTM Committee F17 on Plastic
APWA Uniform Color Code
Piping Systems and is the direct responsibility of Subcommittee F17.26 on Olefin
Based Pipe.
Current edition approved July 1, 2012. Published October 2012. Originally
3
approved in 1972. Last previous edition approved in 2010 as D3035 – 10. DOI: Available from the National Sanitation Foundation, P.O. Box 1468,AnnArbor,
10.1520/D3035-12. MI 48106.
2 4
For referenced ASTM standards, visit the ASTM website, www.astm.org, or .Available from Plastics Pipe Institute (PPI), 105 Decker Court, Suite 825,
contact ASTM Customer Service at [e-mail]. For Annual Book of ASTM Irving, TX 75062, http://www.plasticpipe.org.
5
Standards volume information, refer to the standard’s Document Summary page on APWA, 2345 Grand Boulevard, Suite 500, Kansas City, MO 64018-2641,
the ASTM website. http://www.apwa.net.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1

---------------------- Page: 1 ----------------------
´1
D3035−12
TABLE 1 Polyethylene Compound Requirements
Material
Designation
A B B B
Requirement PE1404 PE2708 PE360 PE4608 PE4710
Required
B
Value
HDB at 140ºF (60ºC), psi 400 (2.76) 800
...