ASTM C142/C142M-17(2023)
(Test Method)Standard Test Method for Clay Lumps and Friable Particles in Aggregates
Standard Test Method for Clay Lumps and Friable Particles in Aggregates
SIGNIFICANCE AND USE
4.1 This test method is of primary significance in determining the acceptability of aggregate with respect to the requirements of Specification C33/C33M.
SCOPE
1.1 This test method covers the approximate determination of clay lumps and friable particles in aggregates.
1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
Note 1: Sieve sizes openings are identified by their Specification E11 designation with their alternative Specification E11 designation given in parentheses for information only.
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: C142/C142M − 17 (Reapproved 2023) American Association of State
Highway and Transportation Officials Standard
AASHTO No. T112
Standard Test Method for
1
Clay Lumps and Friable Particles in Aggregates
This standard is issued under the fixed designation C142/C142M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Determining Mass and Volume for Use in Physical Testing
of Hydraulic Cements
1.1 This test method covers the approximate determination
E11 Specification for Woven Wire Test Sieve Cloth and Test
of clay lumps and friable particles in aggregates.
Sieves
1.2 The values stated in either SI units or inch-pound units
3. Terminology
are to be regarded separately as standard. The values stated in
each system may not be exact equivalents; therefore, each
3.1 Definitions:
system shall be used independently of the other. Combining
3.1.1 For definitions of terms used in this test method, refer
values from the two systems may result in non-conformance
to Terminology C125.
with the standard.
4. Significance and Use
NOTE 1—Sieve sizes openings are identified by their Specification E11
designation with their alternative Specification E11 designation given in 4.1 This test method is of primary significance in determin-
parentheses for information only.
ing the acceptability of aggregate with respect to the require-
1.3 This standard does not purport to address all of the ments of Specification C33/C33M.
safety concerns, if any, associated with its use. It is the
5. Apparatus
responsibility of the user of this standard to establish appro-
priate safety, health, and environmental practices and deter- 5.1 Balance—A balance or scale accurate to within 0.1 % of
mine the applicability of regulatory limitations prior to use. the mass of the test sample at any point within the range of use.
1.4 This international standard was developed in accor- Balances shall conform to the accuracy of the applicable
dance with internationally recognized principles on standard- sections of Specification C1005.
ization established in the Decision on Principles for the
5.2 Containers—Rust-resistant containers of a size and
Development of International Standards, Guides and Recom-
shape that will permit the spreading of the sample on the
mendations issued by the World Trade Organization Technical
bottom in a thin layer.
Barriers to Trade (TBT) Committee.
5.3 Sieves—Sieves conforming to Specification E11.
2. Referenced Documents
5.4 Drying Oven—An oven providing free circulation of air
2
and capable of maintaining a temperature of 110 °C 6 5 °C
2.1 ASTM Standards:
[230 °F 6 10 °F].
C33/C33M Specification for Concrete Aggregates
C117 Test Method for Materials Finer than 75-μm (No. 200)
6. Samples
Sieve in Mineral Aggregates by Washing
6.1 Aggregate for this test method shall consist of the
C125 Terminology Relating to Concrete and Concrete Ag-
material remaining after completion of testing in accordance
gregates
with Test Method C117. To provide the quantities designated in
C1005 Specification for Reference Masses and Devices for
6.3 and 6.4, it may be necessary to combine material from
more than one test by Test Method C117.
1
This test method is under the jurisdiction of ASTM Committee C09 on
6.2 Dry the aggregate to substantially constant mass at a
Concrete and Concrete Aggregatesand is the direct responsibility of Subcommittee
temperature of 110 °C 6 5 °C [230 °F 6 10 °F].
C09.20 on Aggregates.
Current edition approved Oct. 1, 2023. Published October 2023. Originally
6.3 Test samples of fine aggregate shall consist of the
approved in 1938. Last previous edition approved in 2017 as C142/C142M–17.
particles coarser than a 1.18 mm (No. 16) sieve and shall have
DOI: 10.1520/C0142_C0142M-17R23.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or a mass not less than 25 g.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
6.4 Separate the test samples of coarse aggregate into
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. different sizes, using the following sieves: 4.75 mm (No. 4),
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
C142/C142M − 17 (2023)
3 3 1
9.5 mm ( ⁄8 in.), 19.0 mm ( ⁄4 in.), and 37.5 mm (1 ⁄2 in.). The 8. Calculation
test sample shall ha
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.