ASTM D6155-19
(Specification)Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures
Standard Specification for Nontraditional Coarse Aggregates for Asphalt Paving Mixtures
ABSTRACT
This specification deals with the use of coarse aggregates not traditionally used in bituminous paving mixtures. The coarse aggregates shall consist of hard, strong, durable pieces, free of adherent coatings. The grading shall conform to the requirements prescribed herein. Physical properties such as degradation, expansion, and environmental stability shall also be tested.
SCOPE
1.1 This specification covers the use of coarse aggregates not traditionally used in asphalt paving mixtures. These nontraditional aggregates can be described as any aggregate other than those described in Specifications D692/D692M, D693, D1139/D1139M, and D5106 (crushed stone, crushed hydraulic-cement concrete, crushed blast-furnace slag, steel furnace slag, and crushed gravel) suitable for use in asphalt paving mixtures, as described in Specification D3515 or D4215.
1.2 The text of this specification references notes and footnotes that provides explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
Note 1: Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information only and does not represent a different standard sieve size.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
General Information
Relations
Buy Standard
Standards Content (Sample)
This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the
Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
Designation: D6155 −19
Standard Specification for
Nontraditional Coarse Aggregates for Asphalt Paving
1
Mixtures
This standard is issued under the fixed designation D6155; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope 2. Referenced Documents
2
1.1 This specification covers the use of coarse aggregates 2.1 ASTM Standards:
not traditionally used in asphalt paving mixtures. These non- C29/C29M Test Method for Bulk Density (“Unit Weight”)
traditional aggregates can be described as any aggregate other and Voids in Aggregate
than those described in Specifications D692/D692M, D693, C88/C88M Test Method for Soundness of Aggregates by
D1139/D1139M, and D5106 (crushed stone, crushed Use of Sodium Sulfate or Magnesium Sulfate
hydraulic-cement concrete, crushed blast-furnace slag, steel C125 Terminology Relating to Concrete and Concrete Ag-
furnace slag, and crushed gravel) suitable for use in asphalt gregates
paving mixtures, as described in Specification D3515 or C131/C131M Test Method for Resistance to Degradation of
D4215. Small-Size Coarse Aggregate by Abrasion and Impact in
the Los Angeles Machine
1.2 The text of this specification references notes and
C136/C136M Test Method for Sieve Analysis of Fine and
footnotes that provides explanatory material. These notes and
Coarse Aggregates
footnotes (excluding those in tables and figures) shall not be
C142/C142M Test Method for Clay Lumps and Friable
considered as requirements of the specification.
Particles in Aggregates
1.3 The values stated in SI units are to be regarded as
C294 Descriptive Nomenclature for Constituents of Con-
standard. No other units of measurement are included in this
crete Aggregates
standard.
D8 Terminology Relating to Materials for Roads and Pave-
ments
NOTE 1—Sieve size is identified by its standard designation in Speci-
fication E11. The alternative designation given in parentheses is for
D75/D75M Practice for Sampling Aggregates
information only and does not represent a different standard sieve size.
D448 Classification for Sizes of Aggregate for Road and
1.4 This standard does not purport to address all of the
Bridge Construction
safety concerns, if any, associated with its use. It is the D692/D692M Specification for Coarse Aggregate for Bitu-
responsibility of the user of this standard to establish appro-
minous Paving Mixtures
priate safety, health, and environmental practices and deter- D693 Specification for Crushed Aggregate for Macadam
3
mine the applicability of regulatory limitations prior to use.
Pavements (Withdrawn 2008)
1.5 This international standard was developed in accor- D1139/D1139M Specification for Aggregate for Single or
dance with internationally recognized principles on standard-
Multiple Bituminous Surface Treatments
ization established in the Decision on Principles for the D2489/D2489M Test Method for Estimating Degree of Par-
Development of International Standards, Guides and Recom-
ticle Coating of Asphalt Mixtures
mendations issued by the World Trade Organization Technical D3319 Practice for the Accelerated Polishing of Aggregates
Barriers to Trade (TBT) Committee.
Using the British Wheel
1 2
This specification is under the jurisdiction of ASTM Committee D04 on Road For referenced ASTM standards, visit the ASTM website, www.astm.org, or
and Paving Materials and is the direct responsibility of Subcommittee D04.50 on contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
Aggregate Specifications. Standards volume information, refer to the standard’s Document Summary page on
Current edition approved Nov. 1, 2019. Published November 2019. Originally the ASTM website.
3
approved in 1997. Last previous edition approved in 2015 as D6155 – 15. DOI: The last approved version of this historical standard is referenced on
10.1520/D6155-19. www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6155 − 19
D3515 Specification for Hot-Mixed, Hot-Laid Bituminous used is dependent upon the desired composition of the paving
3
Paving Mixtures (Withdrawn 2009) mixture and shall be determined by the purchaser.
D3665 Practice for Random Sampling of Construction Ma-
5.3 Fractured Particles in Coarse Aggregate—Orders for
terials
material under this specification shall state the appropriate
D4215 Specification for Cold-Mixed, Col
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D6155 − 15 D6155 − 19
Standard Specification for
Nontraditional Coarse Aggregates for BituminousAsphalt
1
Paving Mixtures
This standard is issued under the fixed designation D6155; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope
1.1 This specification covers the use of coarse aggregates not traditionally used in bituminousasphalt paving mixtures. These
nontraditional aggregates can be described as any aggregate other than those described in Specifications D692D692/D692M, D693,
D1139D1139/D1139M, and D5106, (crushed stone, crushed hydraulic-cement concrete, crushed blast-furnace slag, steel furnace
slag, and crushed gravel) suitable for use in bituminousasphalt paving mixtures, as described in SpecificationsSpecification D3515
or D4215.
1.2 The text of this specification references notes and footnotes that provides explanatory material. These notes and footnotes
(excluding those in tables and figures) shall not be considered as requirements of the specification.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
NOTE 1—Sieve size is identified by its standard designation in Specification E11. The alternative designation given in parentheses is for information
only and does not represent a different standard sieve size.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety safety, health, and healthenvironmental practices and determine the
applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization
established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued
by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
2. Referenced Documents
2
2.1 ASTM Standards:
C29/C29M Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate
C88C88/C88M Test Method for Soundness of Aggregates by Use of Sodium Sulfate or Magnesium Sulfate
C125 Terminology Relating to Concrete and Concrete Aggregates
C131C131/C131M Test Method for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the
Los Angeles Machine
C136C136/C136M Test Method for Sieve Analysis of Fine and Coarse Aggregates
C142C142/C142M Test Method for Clay Lumps and Friable Particles in Aggregates
C294 Descriptive Nomenclature for Constituents of Concrete Aggregates
D8 Terminology Relating to Materials for Roads and Pavements
D75D75/D75M Practice for Sampling Aggregates
D448 Classification for Sizes of Aggregate for Road and Bridge Construction
D692D692/D692M Specification for Coarse Aggregate for Bituminous Paving Mixtures
3
D693 Specification for Crushed Aggregate for Macadam Pavements (Withdrawn 2008)
D1139D1139/D1139M Specification for Aggregate for Single or Multiple Bituminous Surface Treatments
D2489D2489/D2489M Test Method for Estimating Degree of Particle Coating of Asphalt Mixtures
1
This specification is under the jurisdiction of ASTM Committee D04 on Road and Paving Materials and is the direct responsibility of Subcommittee D04.50 on Aggregate
Specifications.
Current edition approved June 1, 2015Nov. 1, 2019. Published July 2015November 2019. Originally approved in 1997. Last previous edition approved in 20132015 as
D6155 – 13.D6155 – 15. DOI: 10.1520/D6155-15.10.1520/D6155-19.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
3
The last approved version of this historical standard is referenced on www.astm.org.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D6155 − 19
D3319 Practice for the Accelerated Polishing of Aggregates Using the British Wheel
3
D3515 Specification for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures (Withdrawn 2009)
D3665 Practice for Random Sampling of Construction Materials
D4215
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.