ASTM D4730-13
(Specification)Standard Specification for Flooding Compounds for Telecommunications Wire and Cable
Standard Specification for Flooding Compounds for Telecommunications Wire and Cable
ABSTRACT
This specification covers a variety of compounds used for flooding the shields and armors of telecommunications wires and cables (both electrical and fiber optic) for the purpose of preventing water and other undesirable fluids from entering or migrating along or through the cable sheath. The material may be of any chemical composition suitable for the intended purpose and should meet the requirements specified. The flooding compound shall display adhesive properties to provide adhesion between metallic sheath elements and the outer jacket materials of wire and cable. All flooding compounds manufactured in conformance to this specification shall meet the following requirements: homogeneity and foreign material.
SCOPE
1.1 This specification covers a variety of compounds used for flooding the shields and armors of telecommunications wires and cables (both electrical and fiber optic) for the purpose of preventing water and other undesirable fluids from entering or migrating along or through the cable sheath. (For related standards see Specifications D4731 and D4732.)
General Information
Relations
Buy Standard
Standards Content (Sample)
NOTICE: This standard has either been superseded and replaced by a new version or withdrawn.
Contact ASTM International (www.astm.org) for the latest information
Designation:D4730 −13
Standard Specification for
Flooding Compounds for Telecommunications Wire and
1
Cable
This standard is issued under the fixed designation D4730; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Terminology
1.1 This specification covers a variety of compounds used 3.1 Definitions of Terms Specific to This Standard:
for flooding the shields and armors of telecommunications 3.1.1 flooding compounds—any of several materials used to
wires and cables (both electrical and fiber optic) for the fill the air spaces between the sheath elements of single and
purpose of preventing water and other undesirable fluids from multi-conductorinsulatedwiresandcablesoropticalcablesfor
entering or migrating along or through the cable sheath. (For the purpose of excluding water and other undesirable fluids;
related standards see Specifications D4731 and D4732.) especially with regard to telecommunications wire and cable,
including optical cable, intended for outside aerial or under-
2. Referenced Documents ground installations.
2
3.1.2 producer—the primary manufacturer of the material.
2.1 ASTM Standards:
D6 Test Method for Loss on Heating of Oil and Asphaltic
3.1.3 suppliers—jobbers and distributors as distinct from
Compounds
producers.
D92 Test Method for Flash and Fire Points by Cleveland
4. Ordering Information
Open Cup Tester
D482 Test Method for Ash from Petroleum Products
4.1 Orders for material under this specification shall include
D1321 Test Method for Needle Penetration of Petroleum
the following information:
Waxes
4.1.1 Quantity (mass or volume) of each item,
D3236 Test Method for Apparent Viscosity of Hot Melt
4.1.2 Generic name of the material, such as cable flooding
Adhesives and Coating Materials
compound,
D4565 Test Methods for Physical and Environmental Per-
4.1.3 How furnished (drums or barrels, blocks, etc.),
formance Properties of Insulations and Jackets for Tele-
4.1.4 Certification, if required (see Section 11).
communications Wire and Cable
4.1.5 This specification designation, and
D4568 Test Methods for Evaluating Compatibility Between
4.1.6 Any special requirements, as listed in 8.2 and 9.2, that
Cable Filling and Flooding Compounds And Polyolefin
apply.
Wire and Cable Materials
5. Materials and Manufacture
D4731 Specification for Hot-Application Filling Com-
pounds for Telecommunications Wire and Cable
5.1 The material and manufacturing methods used shall be
D4732 Specification for Cool-Application Filling Com- such that the resulting products conform to the properties and
pounds for Telecommunications Wire and Cable
characteristics prescribed in this specification.
E28 Test Methods for Softening Point of Resins Derived
6. Compatibility with Other Materials
from Pine Chemicals and Hydrocarbons, by Ring-and-
Ball Apparatus 6.1 It is the responsibility of the purchaser to ensure that the
flooding compound ordered is suitable for the intended appli-
cation and is compatible with any other components that may
1 come into contact with the flooding compound.
This specification is under the jurisdiction of ASTM Committee D09 on
Electrical and Electronic Insulating Materials and is under the direct responsibility
6.2 The purchaser shall specify the materials that the com-
of Subcommittee D09.07 on Electrical Insulating Materials.
poundmustbecompatiblewithwhentestedinaccordancewith
Current edition approved May 1, 2013. Published June 2013. Originally
approved in 1987. Last previous edition approved in 2008 as D4730 – 02 (2008). Test Method D4568.
DOI: 10.1520/D4730-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or 7. Chemical Composition
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM
7.1 The chemical composition of these materials is not
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website. specified. The material shall be of a chemical composition
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D4730−13
suitable for the intended purpose and which meets the require- 9.3 The purchaser (individual cable manufacturer or other)
ments of this specification as hereinafter stated. shall specify any other expected requirements needed to ensure
compliance with such end-product requirements as cable
7.2 Once established, the producer shall not change the
drip-out temperature and jacket slip.
composition of the compou
...
This document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Because
it may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editions as appropriate. In all cases only the current version
of the standard as published by ASTM is to be considered the official document.
Designation: D4730 − 02(Reapproved 2008) D4730 − 13 An American National Standard
Standard Specification for
Flooding Compounds for Telecommunications Wire and
1
Cable
This standard is issued under the fixed designation D4730; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope Scope*
1.1 This specification covers a variety of compounds used for flooding the shields and armors of telecommunications wires and
cables (both electrical and fiber optic) for the purpose of preventing water and other undesirable fluids from entering or migrating
along or through the cable sheath. (For related standards see Specifications D4731 and D4732.)
2. Referenced Documents
2
2.1 ASTM Standards:
D6 Test Method for Loss on Heating of Oil and Asphaltic Compounds
D92 Test Method for Flash and Fire Points by Cleveland Open Cup Tester
D482 Test Method for Ash from Petroleum Products
D1321 Test Method for Needle Penetration of Petroleum Waxes
D3236 Test Method for Apparent Viscosity of Hot Melt Adhesives and Coating Materials
D4565 Test Methods for Physical and Environmental Performance Properties of Insulations and Jackets for Telecommunications
Wire and Cable
D4568 Test Methods for Evaluating Compatibility Between Cable Filling and Flooding Compounds And Polyolefin Wire and
Cable Materials
D4731 Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable
D4732 Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable
E28 Test Methods for Softening Point of Resins Derived from Naval Stores by Ring-and-Ball Apparatus
3. Terminology
3.1 Definitions of Terms Specific to This Standard:
3.1.1 flooding compounds—any of several materials used to fill the air spaces between the sheath elements of single and
multi-conductor insulated wires and cables or optical cables for the purpose of excluding water and other undesirable fluids;
especially with regard to telecommunications wire and cable, including optical cable, intended for outside aerial or underground
installations.
3.1.2 producer—the primary manufacturer of the material.
3.1.3 suppliers—jobbers and distributors as distinct from producers.
4. Ordering Information
4.1 Orders for material under this specification shall include the following information:
4.1.1 Quantity (mass or volume) of each item,
4.1.2 Generic name of the material, such as cable flooding compound,
4.1.3 How furnished (drums or barrels, blocks, etc.),
4.1.4 Certification, if required (see Section 11).
4.1.5 This specification designation, and
1
This specification is under the jurisdiction of ASTM Committee D09 on Electrical and Electronic Insulating Materials and is under the direct responsibility of
Subcommittee D09.18 on Solid Insulations, Non-Metallic Shieldings and Coverings for Electrical and Telecommunication Wires and Cables.
Current edition approved May 1, 2008May 1, 2013. Published June 2008June 2013. Originally approved in 1987. Last previous edition approved in 20022008 as
D4730 – 02.D4730 – 02 (2008). DOI: 10.1520/D4730-02R08.10.1520/D4730-13.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM Standards
volume information, refer to the standard’s Document Summary page on the ASTM website.
*A Summary of Changes section appears at the end of this standard
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
1
---------------------- Page: 1 ----------------------
D4730 − 13
4.1.6 Any special requirements, as listed in 8.2 and 9.2, that apply.
5. Materials and Manufacture
5.1 The material and manufacturing methods used shall be such that the resulting products will conform to the properties and
characteristics prescribed in this specification.
6. Compatibility with Other Materials
6.1 It is the responsibility of the purchaser to ensure that the flooding compound ordered is suitable for the intended application
and is compatible with any other components that may come into contact with the flooding compound.
6.2 The purchaser shall specify the materials that the compound must be compatible with when tested in accordance with Test
Method D4568.
7. Chemical Composition
7.1 The chemical composition of these materials is not
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.